Straighten out your workshop with Gridfinity modular storage - deploy these plates anywhere you need some order!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Frame: https://a360.co/3ccHbsg
- Weighted Plate: https://a360.co/3uCJ2gR

The foundation of every Gridfinity setup is a baseplate, and these let you drop storage where you need it most.

**Frame**: The absolutely minimal no-frills baseplate. No room for screws or magnets, but saves filament and headroom. If your storage unit is on a steel surface, you can still put magnets in the storage blocks to keep them from sliding.

**Weighted**: Heavy, sturdy baseplate perfect for desktops, shelves, and other places where knocking stuff over is a big problem. 

Secure blocks permanently with [M3 screws,](https://amzn.to/37IaXTg) or temporarily with [6x2mm magnets](https://amzn.to/37Ihopq). Add [rubber feet](https://amzn.to/3LZv4v5) to keep the whole shebang from sliding, and [metal tire weights ](https://amzn.to/3uAzH9f)to drop the center of gravity and prevent wipeouts. You don't need to install every magnet, foot, and weight! Just use enough for your needs.

A Prusa i3 Mk3 can print up to a 5x5 grid. No matter what you use, make sure your bed adhesion and release is dialed in - these love to curl, and their high surface area can make them challenging to remove.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider plates can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Baseplates

Weighted Baseplate 3x2.stl

Frame 1x4.stl

Frame 1x5.stl

Frame 1x6.stl

Frame 1x7.stl

Frame 2x2.stl

Frame 2x3.stl

Frame 1x2.stl

Frame 1x3.stl

Frame 2x7.stl

Frame 3x3.stl

Frame 3x4.stl

Frame 3x5.stl

Frame 3x6.stl

Frame 3x7.stl

Frame 4x4.stl

Frame 4x5.stl

Frame 4x6.stl

Frame 4x7.stl

Frame 5x5.stl

Frame 5x6.stl

Frame 5x7.stl

Frame 6x6.stl

Frame 6x7.stl

Frame 2x5.stl

Frame 2x6.stl

Weighted Baseplate 1x3.stl

Weighted Baseplate 1x4.stl

Weighted Baseplate 1x5.stl

Weighted Baseplate 1x6.stl

Weighted Baseplate 1x7.stl

Weighted Baseplate 2x2.stl

Weighted Baseplate 1x1 (super cute).stl

Weighted Baseplate 1x2.stl

Weighted Baseplate 2x4.stl

Weighted Baseplate 2x5.stl

Weighted Baseplate 3x6.stl

Weighted Baseplate 3x7.stl

Weighted Baseplate 4x4.stl

Weighted Baseplate 4x5.stl

Weighted Baseplate 4x6.stl

Weighted Baseplate 4x7.stl

Weighted Baseplate 5x5.stl

Weighted Baseplate 5x6.stl

Weighted Baseplate 5x7.stl

Weighted Baseplate 6x6.stl

Weighted Baseplate 6x7.stl

Weighted Baseplate 7x7.stl

Weighted Baseplate 2x7.stl

Weighted Baseplate 3x3.stl

Weighted Baseplate 3x4.stl

Weighted Baseplate 3x5.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**[Have you noticed that Bony Basilisk has a NEW FRIEND?](https://than.gs/m/964165)**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873
**Loose Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942878

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:

**Tight Tolerance Frostbite:**
https://than.gs/m/964164
**Medium Tolerance Frostbite:**
https://than.gs/m/964165
**Loose Tolerance Frostbite:**
https://than.gs/m/964166


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

Print-In-Place, No Supports, Articulating Fidget Toy

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each SNAP will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

Tolerance:
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the Tight tolerance model.  For the other tolerances, please check out the other versions of the model below:

Tight Tolerance Extra Long Bony Basilisk:
Coming Soon
Loose Tolerance Long Bony Basilisk:
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

Print Settings:
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Snow Globe Votive Ornament - Winter Cabin

Insert an LED tea light candle (<38mm dia) in the base to light up the cabin.

Print in place with no supports needed. Brim build plate support recommended.

Updated V2. - Fixed deer antlers and smoke.
Updated V3. - Fixed Cabin

Creative Commons License BY-NC-ND 4.0

Snow Globe Votive Ornament - Winter Cabin

Snow Globe Votive Ornament - Winter Cabin

Insert an LED votive candle in the base to light up the cabin.

Print in place with no supports needed. Brim build plate support recommended.

Creative Commons License BY-NC-ND 4.0

Mount storage right to your printer with the Gridfinity modular workshop storage system - whatever machine you use!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Anycubic Sidecar: https://a360.co/3xonYw4
- Anycubic Top: https://a360.co/3jy22GN
- Lulzbot: https://a360.co/3xobNzx
- Prusa: https://a360.co/3Jzfp47
- Snapmaker: https://a360.co/37Om65m
- E3D Toolchanger: https://a360.co/3rlmn6K

These brackets mount to your 3D printer and allow you to put Gridfinity storage blocks right where you need them! These work especially well for the [Gridfinity 3D-printer accessory kit](https://bit.ly/3jtTfWu).

If you need more adjacent slots, just print multiple baseplates and butt them up against each other. *I STRONGLY recommend magnets or screws so you don't knock stuff into your printer!*

**Anycubic Vyper/Kobra**: Also fits any printer made of extrusion with 6mm slots. Mount to your printer's frame with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD!

The **sidecar** baseplate mounts to the base frame, parallel with the floor, a lot like the included filament holder. The **top-mount** baseplate mounts on the Z axis crossbeam or base frame. *Make sure the gantry, extruder, and plate don't collide with your Gridfinity!*

**Lulzbot**: Fits the upward-facing edges of the top crossbars. This one is a real pain in the butt to install.

**Prusa**: Slides on over the steel frame, no fasteners required. *THE BASEPLATE AND EXTRUDER MUST BE ON OPPOSITE SIDES OF THE FRAME!*

**Snapmaker**: Mount to the optional enclosure with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD! I didn't make one for the printer itself, sorry!

**Toolchanger**: Mount to the top of the printer with three button head M3x5 screws. *Don't use longer screws! They won't fit!*

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Printer-Mounted Baseplates

Anycubic Baseplate, Sidecar.stl

**UPDATE: V6 is here!**  This version is deprecated, go get the latest release here: [https://social.thangs.com/m/637070](url)


------------------------------------------------------------------

- **INCLUDED FILES:**
  - CAD STEP File to learn how I designed these.
  - Right Handed Cup version 5
  - Left Handed Cup version 5
  - Handle-Less Cup
  - Blank Cup (No Logo)

------------------------------------------------------------------

- **PRINT PARAMETERS:** 
  - Requires support under the handle.  The rest of the model should print without support. 
  - Recommend a minimum of 2 perimeters
  - 15%+ infill ratio (rectilinear is my preferred infill)

Check out my other novelty Can Cup designs and more here on Thangs!

-----------------------------------------------------------------

Want to Support what I do? Check out my social medias please!

**Link Tree:** [http://www.MandicReally.com/links](url)

-----------------------------------------------------------------

**This Design Features a Trademarked Logo (Monster Energy) and I make no claims of ownership to that logo.  The Design is covered by a Creative Commons Non-Commercial license and should not be sold commercially by ANYONE.**  No licenses to the design will be granted.  Anyone selling this design is doing so against my wishes and license. The Monster Logo is solely owned, trademarked, and copyrighted by Monster Energy.

PLEASE Credit any and all Remixes of my designs: MandicReally

Kyle Cup V5 - NEW DESIGN - Chad Chalice - Stimulant Stein - Monster Energy Drink Can Cup

CAD STEP File of designs. 

PLEASE CREDIT ANY REMIXES: MandicReally - Alan Mandic

Covered by Creative Commons - Non-Commercial License.

Kyle Cup v5.step

Mechanic? Auto Tech? Car Enthusiast? Well I FOUND THE **10MM**! It was hiding in my 3D Printer!  

This 12oz Can Cup design is inspired by a 10mm Shallow socket.  The Handle equipped version is designed to mimic a **10mm** Combination wrench with open and Box ends (that actually measure 10mm).  The cup body features a hex design in the can opening, a square "Drive" hole in the bottom for can removal, and a #10 inset into the side.  

Perfect for the Car / Tool Enthusiast in your or your life! Thanks to TikTok Live chat for the idea on this one!

Designed for cans with a 66mm Diamater. Cup measures 111mm tall.

-------------------------------------------------------------------

- **INCLUDED FILES:**
  - CAD STEP File to learn how I designed these.
  - 10mm Can Cup with Wrench Handle
  - 10mm Can Cup without Handle

-------------------------------------------------------------------

- **PRINT PARAMETERS:** 
  - Supports Required between bottom and top of handle.
  - 3 Perimeters Recommended.
  - 15%+ Infill Recommended (I Prefer Rectilinear)

Mine was printed in Inland Grey PLA+.

-------------------------------------------------------------------

Check out my other novelty Can Cup designs and more here on Thangs!

Want to Support what I do? Check out my social medias please!

**LinkTree:** http://www.HotRodHippie.com/links

--------------------------------------------------------------

**All of my Designs are covered by a Creative Commons Non-Commercial LIcense.**  Sale of prints using my designs are the sole right of myself, the designer, and those I license to do so. Please understand every design is hours of work and multiple prototype prints to ensure quality.  Unauthorized sales will result in new designs not being made public.

PLEASE Credit any and all Remixes of my designs: MandicReally

10mm Shallow Can Cups - 12oz Soda Pop Can Cups

CAD STEP File of the Designs for Educational Purposes.

PLEASE Credit any Remixes: MandicReally

10mm Cups.step

A decorative sailing boat model which can be printed without supports.

Prints in two halves and slots together

** I have also designed a stand for the model which you can download here: https://social.thangs.com/m/106179

For the sail print at 0.3mm layer height.

If you are using Prusaslicer check the 'detect thin walls' box and make sure the 'wipe while retracting' is unchecked on your printer settings.

Sailboat - no supports

Sailboat DISPLAY ONLY.stl

Miniature milk crates for your decorating and storage needs!

No supports necessary and easily fits on most entry level 3D printers. No supports needed*  and can be scaled small or big!
* - slot handle may require support based on your printer and size

LxWxH
(1) 3 3/4" x 3 3/4" x 3 3/4"
(1) 3" x 3" x 3"
(1) 2 1/4" x 2 1/4" x 2 1/4"

Support Free Milk Crate

Crate Sizes.sat

This is one of my 12oz Can "Cup" designs.  Intended to be a fun and "stylish" way to enjoy your 12oz canned beverages.  Simple slide your can into the coozie, and enjoy.

Design is meant to mimic that of an old wood barrel. Complete with a cork in the side. Fits standard 66mm 12oz cans.  Also features holes to allow air to escape on insertion, as well as a bottom hole to help push the empty can out.

- **UPDATES (05/30/2021):**
  - Modified design to have the proper bottom hole design to be used with the new "Can Cup Ejector" tool for can removal.

------------------------------------------------------------------

- **INCLUDED FILES:**
  - Handle Version
  - No Handle Version (Barrel Only)
  - CAD STEP file for both designs. 

-----------------------------------------------------------------

- **PRINT PARAMETERS:** 
  - Requires support under the handle and between the top/bottom portions of the handle.  
  - No Handle version doesn't require supports.
  - 3 Perimeters Recommended (Walls / Shells)
  - Minimum 15% Infill Recommended

I printed with Eeryone Silk "Dark Gold" PLA. 

------------------------------------------------------

Want to Support what I do? Check out my social medias please!

**LinkTree:** http://www.HotRodHippie.com/links

--------------------------------------------------------

**All of my Designs are covered by a Creative Commons Non-Commercial License.**  Sale of prints using my designs are the sole right of myself, the designer, and those I license to do so. Please understand every design is hours of work and multiple prototype prints to ensure quality.  Unauthorized sales will result in new designs not being made public.

PLEASE Credit any and all Remixes of my designs: MandicReally

Root Beer Barrel - 12oz Can Coozie aka Stein for your Soda Pop Cans!

CAD STEP File of the Root Beer Barrels so you can see a bit of how I designed them.  If you use Remix my design please provide credits to me, MandicReally aka The HotRodHippie!

Barrel Can V2.step

Dragon Head 1 - Fan Art - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Dragon Head 1 - Fan Art - Decoration

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Loose Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942878

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Tightness Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Loose Tolerance Extra Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

This design is inspired by the Mini Nukes from Fallout 4 and is a fun way to hold your 12oz Beverages! A fun and silly can koozie for your soda, pop, soda pop, seltzers, and beer enjoyment!  NOW INCLUDING A NOSE CONE! The new add-on turns the Mini-Nuke into a display model or storage box! (Plug and Nose Cone are available separately for those who already downloaded this design previously.)

This design is LARGE as the design required to really get the full effect. The handled version is 166.80mm wide by 140mm wide by 159.50mm Tall. **Make sure your print volume can fit it!** The diameter of the main body is 116mm so the Handle-Less version isn't for small hands.

Fits standard 66mm 12oz cans.  Also features a bottom hole to help push the empty can out and allow air to escape while installing the can.

- **UPDATES (05/30/2021):**
  - Added "Nose Cone" file so you can use the design as a more complete display!
  - Added a "Plug" to cover the hole in the bottom so it can be used as a storage box.

------------------------------------------------------------------

- **INCLUDED FILES:**
  - Handled Version
  - Handle-Less Version 
  - CAD STEP File to see the designs and learn.

------------------------------------------------------------------

- **PRINT PARAMETERS:**
  - No Supports Required for the Cup.
  - "Nose Cone" requires support on outer brim edge, but not in the middle.
  - 3 Perimeters minimum Recommended
  - 15-25% Infill Recommended

Mine was printed in "Army Green" Jessie PLA from Printed Solid.

--------------------------------------------------------------

Want to Support what I do? Check out my social medias please!

**LinkTree:** http://www.HotRodHippie.com/links

--------------------------------------------------------------

**All of my Designs are covered by a Creative Commons Non-Commercial License.**  Sale of prints using my designs are the sole right of myself, the designer, and those I license to do so. Please understand every design is hours of work and multiple prototype prints to ensure quality.  Unauthorized sales will result in new designs not being made public.

PLEASE Credit any and all Remixes of my designs: MandicReally


12oz Mini Nuke - Fallout 4 Can Cup!

CAD STEP Files of the designs.  Just provided so you can see how I made the designs or make tweaks if you need.

PLEASE CREDIT any Remixes: MandicReally

Nuke Cups STEPS v1.step

Nose Cone add-on for the Mini-Nuke Can Cups.  Turn your Can Koozie into a display model with this Nose Cone inspired by the Fallout 4 Mini Nukes.  Combine with the "plug" to convert the cup into a storage box. 

Mini Nuke Cup 

A cover plate for the hole in the bottom of the Mini Nuke Can Cup.  This add-on covers the bottom of hole of the cup so you can now use your Can Koozie as a Storage box.  Combine with the new Nose Cone to close up the box.

Mini Nuke Hole Plug

Demon Skull - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.


Demon Skull - Decoration

It is a CAN GRENADE, obviously...  This is a 12oz Can "Cup" to hold whatever 12oz beverages you may enjoy.  Whether it be soda pop, seltzer, or beer you can have a fun holder with (or without) a handle for it! 

This is one of my 12oz Can "Cup" designs.  Intended to be a fun and "stylish" way to enjoy your 12oz canned beverages.  Simple slide your can into the koozie, and enjoy.

Fits standard 66mm 12oz cans.  Also features holes to allow air to escape on insertion, as well as a bottom hole to help push the empty can out.

---------------------------------------------------------------

- **INCLUDED FILES:**
  - "Free Floating" Handle Version
  - Handle-Less Version
  - "Bed Adhesion" Version with Handle attached at bottom.
  - "Pin" to complete the look.
  - CAD STEP File to see the designs and learn.

---------------------------------------------------------------

- **PRINT PARAMETERS:** 
  - No support required
  - 3 Perimeters Recommended (Walls / Shells)
  - 10%+ Infill Recommended
  - The "GrenadeCanV2" file is a challenging print if you have bed adhesion issues.  That is why the file has an included Raft on the handle.  
  - If you are concerned about that print the "GrenadeCanBedAdhesionV2" file as it has a brace attaching the handle to the main body for better bed adhesion / handle support.

I printed with Eeryone Silk "Bronze" PLA. 

--------------------------------------------------------------

Want to Support what I do? Check out my social medias please!

**Link Tree:** http://www.HotRodHippie.com/links

--------------------------------------------------------

**All of my Designs are covered by a Creative Commons Non-Commercial License.**  Sale of prints using my designs are the sole right of myself, the designer, and those I license to do so. Please understand every design is hours of work and multiple prototype prints to ensure quality.  Unauthorized sales will result in new designs not being made public.

PLEASE Credit any and all Remixes of my designs: MandicReally

CAN GRENADE! - 12oz Can Cup 

THE CAN GRENADE!  CAD STEP File so you can see how I designed these or tweak them if you want/need. 

Please credit any Remixes of my designs to me: MandicReally

GrenadeCansV2.step

Elevate your home decor with a fusion of style and functionality with our Skull Phone Holder 3D model at Thangs.com. The creativity imbibed in this unique design makes it a great accessory and an absolute stand-out in our "Home & Garden" category. Intricately designed by printedobsession, this striking skull-shaped phone holder is not just visually engaging, but it also promises utility and convenience. With this innovative design, you'll never have to worry about misplacing your phone ever again. The detailed images from various angles allow you to visualize how the model would add an edge to your living space, making it an instant conversation starter. The skull phone holder is not just appealing but also a testament to striking details crafted to perfection. For more insights into this 3D model, you can visit our website. Remember, your space speaks about you. Make it loud

Skull Phone Holder - Home Decoration

Eastern Dragon - Dragon head - Decoration

If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Eastern Dragon - Dragon head - Decoration

To see more projects like this one follow :
https://www.instagram.com/Concretize_3d/

Veja aqui como surgiu a ideia para esse modelo:

https://youtu.be/DRB0SRgHDY4

Este é um suporte "Print in Place" com regulagem de inclinação para apoiar celulares, tablets, Ipads, Iphones, inclusive controles de videogames.

Super prático e fácil de ajustar, sai da impressora pronto para o uso, você ajusta na inclinação que deseja para apoiar seu celular, tablet ou controle!


Baixe e compartilhe com seus amigos para que todos aproveitem !!

Print in Place - Suporte Articulado Celular Tablet com Porta Caneta.stl

Este é um suporte "Print in Place" com regulação de inclinação para apoiar celulares, tablets, Ipads, Iphones, inclusive controles de videogames.

Super prático e fácil de ajustar, sai da impressora pronto para o uso, você ajusta na inclinação que deseja para apoiar seu celular, tablet ou controle!

Baixe e compartilhe com seus amigos para que todos aproveite !!

Print in Place - Suporte Articulado Celular Tablet e Controle Gamer.stl

Vampire Skull - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Vampire Skull - Decoration

A 3D Printable organizer for your desk or workbench. Store your calipers, tape measurer, flash drives, SD cards (both full size and micro), and your writing utensils. A phone stand is integrated into the organizer, which is compatible with Mag Safe for wireless charging. Underneath the phone stand are three drawers for storing cables or small parts that would otherwise get lost. 

There are a couple different versions of this model. You can choose to have the cutout for the Mag Safe, but Android users may prefer to go without this feature. The other option is to print the organizer with accents or without. 

If you choose the model with the accents, then please note this model was NOT designed to be printed with dual extrusion. The accents need to be attached with super glue or a similar adhesive. The reasoning for this is because most people do not have access to dual extrusion or a printer with two extruders that can print a 120 mm x 235 mm x 120 mm (LxWxH) part. Examine the accents before gluing them down. The accent on the left side should match the radius on the back of the organizer and come to a point a with the accent that runs along the front.

My favorite filament for printing this model:
- [Grey marble PLA](https://www.matterhackers.com/store/l/pro-series-pla/sk/MHW2R5AY?aff=7480)
- [Silky PLA](https://www.matterhackers.com/store/c/mh-build-series/mh-build-series-silky-pla?aff=7480)


**Print Settings**
0.4mm Nozzle
0.2mm Layer Height
Support: Print Support for overhangs less than 55 degrees. 

**Socials:**
[Youtube](https://www.youtube.com/c/drdflo)
[Instagram](https://www.instagram.com/dr.dflo)

Please note that affiliate links are present to support the creation of these models.


Home

Categories

Popular

Personalize

Trending