**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**[Have you noticed that Bony Basilisk has a NEW FRIEND?](https://than.gs/m/964165)**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873
**Loose Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942878

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:

**Tight Tolerance Frostbite:**
https://than.gs/m/964164
**Medium Tolerance Frostbite:**
https://than.gs/m/964165
**Loose Tolerance Frostbite:**
https://than.gs/m/964166


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

Print-In-Place, No Supports, Articulating Fidget Toy

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each SNAP will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

Tolerance:
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the Tight tolerance model.  For the other tolerances, please check out the other versions of the model below:

Tight Tolerance Extra Long Bony Basilisk:
Coming Soon
Loose Tolerance Long Bony Basilisk:
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

Print Settings:
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Oogie Boogie from The Nightmare Before Christmas.

Will print with no supports at this size for FDM!


OogieBoogie.stl

**Gift Box #7**

This is the seventh version in a series gift boxes that may look the same on the outside but they each have a secret way of opening. This one uses a planetary gear stage! Turning the bow rotates the sun gear which results in the ring gear turning at a 3:1 ratio. There are external threads on the ring gear which engage with female threads on the box. The planetary gears are aesthetically pleasing but they actually work against you as it takes three more turns to unthread. It’s easy to cross thread, make sure the top is on flat before tightening.

This box is the same as [Gift Box #7]( https://social.thangs.com/m/513748) but the top and bottom print entirely as one piece, so you don’t have to glue the bows and ribbons on.

**Gift Boxes**
**Season 1**
[Gift box #1]( https://thangs.com/3dprintingworld/Gift-Box-37907)
[Gift box #1 Quantum Addition]( https://thangs.com/3dprintingworld/Gift-Box-1-Quantum-Addition--40583)
[Gift box #1 Print-In-Place]( https://thangs.com/3dprintingworld/Gift-Box-1--PrintInPlace--38940)
[Gift Box #2](https://thangs.com/3dprintingworld/Gift-Box-2-39845)
[Gift Box #3](https://thangs.com/3dprintingworld/Gift-Box-3-39372)
[Gift Box #4](https://thangs.com/3dprintingworld/Gift-Box-4-39976)
[Gift Box #5](https://thangs.com/3dprintingworld/Gift-Box-5-40117)
**Season 2**
[Gift Box #6]( https://social.thangs.com/m/505224)
[Gift Box #6 Print-in-Place](https://social.thangs.com/m/505938)
[Gift Box #7]( https://social.thangs.com/m/513748)
[Gift Box #7 Print-in-Place]( 
https://social.thangs.com/m/518615)
[Gift Box #9]( 
hhttps://social.thangs.com/m/533662)
[Gift Box #10]( 
https://social.thangs.com/m/556228)
[Gift Box #11 Print-in-Place]( 
https://social.thangs.com/m/547371)

Its roughly 100mm x 100m x 80mm tall. The top prints in place as one part, none of the parts require supports. I printed all the parts in the orientation the stl’s are provided in. 

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.

_Note: Assembly model for reference only._
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models by joining my [Patreon](https://www.patreon.com/3dprintingworld)

Valentines Day, Birthday, Xmas, Christmas, Holiday, print in place



Gift Box #7 Print-in-Place

GIFT BOX 7_ASSY_REF ONLY.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Loose Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942878

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Tightness Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Loose Tolerance Extra Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

A  screw together lantern bauble that will hold an led tealight. Can be hung on your Christmas tree or on my Display tree.

Prints without supports.

There are four tree and two base options for my Christmas Bauble Display Tree, download links below.

Starry tree: https://social.thangs.com/m/523430
Minimalist tree: https://social.thangs.com/m/523482
Tree with filled star: https://social.thangs.com/m/523504
Standard tree: https://social.thangs.com/m/37472

Pot Base: https://social.thangs.com/m/523467
Hill Base: https://social.thangs.com/m/523452

Scroll down to 'geometrically related' to see other baubles to hang on my tree

Lantern Bauble

DISPLAY ONLY.stl

A snowflake bauble to hang on my Christmas bauble display tree display.

Prints without supports
Can be attached using the provided hook stl or with cotton

There are four tree and two base options for my Christmas Bauble Display Tree, download links below.

Starry tree: https://social.thangs.com/m/523430
Minimalist tree: https://social.thangs.com/m/523482
Tree with filled star: https://social.thangs.com/m/523504
Standard tree: https://social.thangs.com/m/37472

Pot Base: https://social.thangs.com/m/523467
Hill Base: https://social.thangs.com/m/523452

Snowflake bauble

Snowflake DISPLAY ONLY.stl

Halloween Nightmare Before Christmas Candle- Halloween Decoration

Halloween Nightmare Before Christmas Candle

Nightmare A.stl


**Gift Box Series**
This is the first gift box in a series of boxes that I’m designing for Christmas this year. All the boxes are similar in size and shape but each one opens differently. If you print one I would love to see it,  be sure to post it here or tag me on your socials. 

I hope everyone enjoys printing them as much their loved ones will enjoy receiving them! 🎅🎁

**Gift Boxes**
**Season 1**
[Gift box #1]( https://thangs.com/3dprintingworld/Gift-Box-37907)
[Gift box #1 Quantum Addition]( https://thangs.com/3dprintingworld/Gift-Box-1-Quantum-Addition--40583)
[Gift box #1 Print-In-Place]( https://thangs.com/3dprintingworld/Gift-Box-1--PrintInPlace--38940)
[Gift Box #2](https://thangs.com/3dprintingworld/Gift-Box-2-39845)
[Gift Box #3](https://thangs.com/3dprintingworld/Gift-Box-3-39372)
[Gift Box #4](https://thangs.com/3dprintingworld/Gift-Box-4-39976)
[Gift Box #5](https://thangs.com/3dprintingworld/Gift-Box-5-40117)
**Season 2**
[Gift Box #6]( https://social.thangs.com/m/505224)
[Gift Box #6 Print-in-Place](https://social.thangs.com/m/505938)
[Gift Box #7]( https://social.thangs.com/m/513748)
[Gift Box #7 Print-in-Place]( 
https://social.thangs.com/m/518615)
[Gift Box #9]( 
hhttps://social.thangs.com/m/533662)
[Gift Box #10]( 
https://social.thangs.com/m/556228)
[Gift Box #11 Print-in-Place]( 
https://social.thangs.com/m/547371)
___

This gift box is similar to the original but it prints all in one color in two pieces so no assembly required for those who want it to be ready right off the printer.

The gift box has a little twist! I wanted to design something for Christmas this year that everyone could print for their loved ones to show the amazing ability's of a 3D printer. This is the first in a set of boxes that all have a little trick to open. 

To open it just turn the bow, the bow rotates a spur gear which pulls back the catches and unlocks it.  The catches are spring loaded so you don’t have to worry about the box opening when you don’t want it to. There is a stop so the bow cannot be over rotated. 

Its roughly 100mm x 100m x 80mm tall. The top prints in place as one part, none of the parts require supports. I printed all the parts in the orientation provided at .2 layer heights but the box could definitely be printed at a larger layer height without issue. 

I used [Gorilla Glue](https://amzn.to/3rQpTXw)(aff.) for gluing on the ribbons.  Put the glue in the middle and let it naturally spread out. 
If you don’t already own as set of these [clamps]( https://amzn.to/3lYOqpJ )(aff.) you should pick them up, they really help with gluing the ribbons on.  
___
Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer with [Polyalchemy Elixir](https://www.printedsolid.com/) 

_Note: Assembly model for reference only._
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models by joining my [Patreon](https://www.patreon.com/3dprintingworld)

_Valentines Day, Birthday, Holiday_

Gift Box #1  Print-In-Place 

GIFT BOX-ASSY.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

**Tight Tolerance Long Bony Basilisk:** 
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052


Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Tight Tolerance Short Bony Basilisk: 
https://than.gs/m/936954
Loose Tolerance Short Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

Tight Tolerance Long Bony Basilisk: 
https://than.gs/m/936921
Medium Tolerance Long Bony Basilisk: Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

A screw together Voronoi style egg bunny box

Perfect for Easter egg hunts or as a gift.

Prints without supports

Like my Egg Bunnies? Find my Egg Piggies here: https://than.gs/m/817881

Egg Bunny Gift Pot

Discover a unique 3D printed Skull Bowl, one of the standout pieces in the Arts & Entertainment category on thangs.com. This spooky yet fascinating Halloween decoration is the perfect addition to any haunting collection. Designed by Printed Obsession, the Skull Bowl brings a blend of artistic creativity and utility, offering an eerie bowl disguised as a realistic human skull. Ideal as a Halloween decoration, it takes Halloween-themed party essentials to a new level, providing an excellent talking point for your guests while doubling as serving bowls for sweet treats or fruits. Dip into the detailed images provided to get an up-close glimpse into the fantastic details of this 3D model before you bring it to life. With all aspects, from the hollowed-out cranium to the detailed facial features, it's clear this model was meticulously crafted by experts. Dive into our expanding library for more amazing Halloween models!

Skull Bowl - Halloween Decoration

Bulbasaw - halloween - Pokemon - Fan art
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Bulbasaw - halloween - Pokemon - Fan art

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.


This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk: **
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk: **
https://than.gs/m/937047

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

**Tight Tolerance Long Bony Basilisk: **
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk: **
Coming Soon
**Loose Tolerance Long Bony Basilisk: **
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Please "like" this thing to help it rise in the search results, especially if you download it or add it to a collection.

It's a threaded dragon egg, great for Easter egg hunts, gifts, and Game of Thrones fans.

The whole egg measures 63mm tall by 45mm wide. I will soon add large and extra large versions.

This is a remix of my own threaded Easter egg. I made every bit of this from scratch, including the scales. I made the scales by importing a custom texture into a Blender brush and placing every scale one at a time, adjusting the size as I went. I designed it with Sketchup, Blender, and Meshmixer. (And Gimp for the scale alpha.)

If you like this design and want to show your support, you can share your make, leave a review, or buy me a coffee (via [Paypal](https://www.paypal.me/tonyyoungblood), [Venmo](https://www.venmo.com/u/Tony-Youngblood), or [CashApp](https://cash.app/$TonySYoungblood)). I appreciate 
you.

Instructions:

1. Print the bottom and top pieces as oriented in the files. Supports are not required. I recommend a layer height of 0.2mm or smaller, wall thickness of 1.2mm, a bottom thickness of 0.6mm, and a top thickness of 0.8mm. Infill density of 12 percent or higher. I tried to allow for horizontal expansion in the design, so first try printing it without adjusting horizontal expansion, slicing tolerance,  or x/y compensation. If it prints too tight or too loose, then you can use one of those slicing features to compensate. Threads are notorious for being the hardest item to print, so please be patient. If you want to save time while testing, you can print the included calibration test instead of the full model. 
2. Once printed, screw the threads in and out repeatedly to remove any stray particles. It may feel too tight on the first threading but should screw easily after ten seconds of doing this.    
3. Note the small nubs near the threads. Refer to the pictures to see what I'm talking about.  When the two nubs are parallel, you know you've got the proper alignment.

Licensed under Creative Commons Attribution Share Alike. If you sell prints of this file, please respect the license and credit me on the sales page with a link to this page.

Threaded Dragon Egg, Great for Easter and Gifts

DragonEggStandardBottom.stl

An Angel bauble to hang on my Christmas bauble display tree display.

Prints without supports
Can be attached using the provided hook stl or with cotton

There are four tree and two base options for my Christmas Bauble Display Tree, download links below.

Starry tree: https://social.thangs.com/m/523430
Minimalist tree: https://social.thangs.com/m/523482
Tree with filled star: https://social.thangs.com/m/523504
Standard tree: https://social.thangs.com/m/37472

Pot Base: https://social.thangs.com/m/523467
Hill Base: https://social.thangs.com/m/523452

Angel bauble

Angel DISPLAY ONLY.stl

If you're a fan of pop culture and love Halloween, this 3D model of "Bluey - Halloween Costume - Fan Art" found on Thangs.com is perfect for you! This expertly designed and realistic model brings Bluey, the popular animated dog character, to life in a fun and festive Halloween costume. Made with incredible detail and precision, this 3D model is a great choice for any fan of the show or anyone seeking to add to their collection of pop culture 3D models. Ideal for 3D printing or digital projects, the Bluey Halloween Costume model showcases the craftsmanship you can find at Thangs.com. View the images and further details on the Thangs.com page to fully appreciate the intricate details that make this 3D model a must

If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Bluey - Halloween Costume - Fan Art

Stash your treats in these decorative Easter Eggshells! Contents are secured inside with a threaded insert on the bottom. 
See here for video: https://youtu.be/bnmHGWe-gvg 
This design is part of a set of ten decorative Easter Eggshells entered into the Spring 2022 Thangs #MakerMadness design competition. 
The latticing and surfaces were designed using nTopology. Here’s a bit more information on each model:
Eggshell 1: Surface derived from the gyroid TPMS
Eggshell 2: Lattice derived from the Kelvin graph
Eggshell 3: Rotated Square Honeycomb
Eggshell 4: Surface derived from the SplitP TPMS
Eggshell 5: Surface derived from the gyroid TPMS (different orientation then Eggshell 1)
Eggshell 6: Lattice derived from a cluster of columns
Eggshell 7: Surface derived from the Schwarz diamond TPMS
Eggshell 8: Surface derived from the Fischer-Koch S TPMS
Eggshell 9: Hexagonal Honeycomb
Eggshell 10: Surface derived from the Schoen F-RD TPMS


Seasonal

Categories

Popular

Personalize

Trending