The Monstera leaf is so iconic, who wouldn't want one on their fridge? This is a simple print that would be great for plant people.

This can be a one or two color print. The top layer is .2mm thick, so if using Bumbu Studio/OrcaSlicer, all you have to do is paint the veins with a one click fill of the top layer.

I've included two sizes — small (4" - pictured) and large (5")

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the 10x2.3mm magnets.

**Orientation**
Print with the vein side up, magnet side down.

**Print Settings**
*I've included the 3MF if you want to use my settings.
- .2mm layer height
- 15% grid infill
- 2 walls

**Links (some may be affiliate links)**
Filament I used for this print: [Hatchbox Forest Green PLA](https://amzn.to/3T7aeAJ) & [Overture Matte White PLA](https://amzn.to/3sQqvzz)
Magnets: [10x2.3mm Small Round Fridge Magnets](https://amzn.to/3Svx4C2)

Monstera Leaf Magnet

Monstera Leaf Magnet Small.stl

Another lamp! This is a pretty lengthy print, but worth it in my opinion. It uses the same shades and pendant light kits as my previous lamps.

The pendant light includes a locking ring that secures it to the base. To install, just insert the socket up through the bottom of the base, and screw on the locking ring to clamp it in place.

Note that you must **only use LED bulbs (9 watts max)** as traditional bulbs can get pretty hot and could cause damage to the plastic. I like these [multi color smart bulbs](https://amzn.to/47h8BVk) that I can control with my phone, but any standard 9W LED bulb will do.

**Supports**
Supports are needed on the base for the shoulder that holds the pendant light socket in place, as well as the opening for the cord. I used normal snug supports.

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the pendant light socket. 

**Orientation**
The base and shade should be right side up.

**Print Settings**
*I've included the 3MF if you want to use my settings.

Base
.2mm layer height
15% grid infill
2 walls

Shade
.2mm layer height
10% concentric infill on the shade. If you use a concentric infill pattern on the whole shade, the supports that attach to the base will print without any infill. So I added a cylindrical modifier for the shade supports that uses a 15% grid infill pattern.
2 walls

**Links (some may be affiliate links)**
Filament I used for this print: [Overture Matt Black PLA](https://amzn.to/3szwvMV) & [Overture Matte White PLA ](https://amzn.to/3QJDSZZ)
[Pendant Light Cord Lamp Kit](https://amzn.to/3G2xmst)

Cleo Lamp

Cleo Lamp Body.stl

Vase Mode Shade 1.stl

Vase Mode Shade 2.stl

Vase Mode Shade Support.stl

Vase Mode Shade.3mf

Ring Shade Support.stl

Vase Mode Shade 3.stl

This is how I originally designed the Poppy, and I'm bringing it back! It uses the same mounts as all my other wall mounted planters.

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the command strips and the screw holes are designed specifically for #10-12 x 1-1/4 in anchors and screws.

**Orientation**
The planter and tray should have their bottoms on the build plate. All mounts should have the sliding dovetail facing up.

**Print Settings**
.2mm layer height
15% grid infill. I've been using gyroid for the 4.5" command mount and it's much cleaner.
2 walls

**Links (some may be affiliate links)**
Filament I used for this print: [Polymaker Matte Marble PLA ](https://amzn.to/3MDJ14M)
Hardware: [#10-12 x 1-1/4 in screws](https://amzn.to/3QrqTwf)

Big Bubbles Planter

Big Bubbles Pot 4.5.stl

Another mini magnetic vase for flowers, pens, pencils, etc.! This one has a slightly larger hole. For reference — the hole is large enough to hold a standard size Sharpie. Magnets on the back allow you to stick it to your fridge or any magnetic surface.

**Supports**
None needed!

**Scaling**
This one should not be scaled since the holes on the back are sized to fit 10x2.3mm magnets.

**Orientation**
The vase should print right side up.

**Print Settings**
.2mm layer height
15% grid infill
2 walls
Wall/infill print order - outer/inner/infill

**Links (some may be affiliate links)**
Filament I used for this print: [Overture Matte Light Brown PLA](https://amzn.to/47fGCVC)
Magnets: [10x2.3mm Small Round Fridge Magnets](https://amzn.to/3Svx4C2)

Mini Magnetic Vase No. 2

A mini magnetic version of the Wave Vase! Magnets on the back allow you to stick it to your fridge or any magnetic surface.

I have a bunch of different designs for these that I'll be releasing soon so keep an eye out for those!

**Supports**
None needed!

**Scaling**
This one should not be scaled since the holes on the back are sized to fit 10x2.3mm magnets.

**Orientation**
The vase should print right side up.

**Print Settings**
.2mm layer height
15% grid infill
2 walls
Wall/infill print order - outer/inner/infill

**Links (some may be affiliate links)**
Filament I used for this print: [Overture Matte PLA](https://amzn.to/47fGCVC) & [Polymaker Matte Marble PLA](https://amzn.to/3FQ0F1r)
Magnets: [10x2.3mm Small Round Fridge Magnets ](https://amzn.to/3Svx4C2)

Mini Magnetic Vase No. 1

Mini Magnetic Vase No. 1.stl

This is the exact same planter as the Grid, just without the texture so it prints much faster. I really like the simplicity of this one and have put up a bunch of these around my house. It's a pretty neutral design that could blend in to almost any aesthetic.

**Supports**
The only version of this that I've been using supports on is Wall Simple Cup Pot 4.5. All other versions do not need supports.

For Wall Simple Cup Pot 4.5, I use supports under the sliding dovetail on the pot.

The slicer is going to want to add supports underneath the pot as well, which is unnecessary, so I added a support blocker to the whole pot and a support enforcer under the dovetail.

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the command strips and the screw holes are designed specifically for #10-12 x 1-1/4 in anchors and screws.

**Orientation**
The planter and tray should have their bottoms on the build plate. All mounts should have the sliding dovetail facing up.

**Print Settings**
.2mm layer height
15% grid infill. I've been using gyroid for the 4.5" command mount and it's much cleaner.
2 walls

**Links (some may be affiliate links)**
Filament I used for this print: [HATCHBOX Magic Stone PLA ](https://amzn.to/40p03JK)
Hardware: [#10-12 x 1-1/4 in screws](https://amzn.to/3QrqTwf)

Simple Cup Planter

Wall Simple Cup Pot 2.75.stl

A planter for people who like plants but can't keep them alive! And maybe they also have something to hide...

This is a super easy print. It prints in 3 parts - the pot, the lid, and the plant. There is a square hole in the lid that the plant stem pressure fits into.

I'm planning on releasing a bunch more plants (and maybe other non-plant designs) that will be interchangeable so you can swap them out whenever you want. Thinking this will be fun for holidays (Christmas trees, hearts, flags, pumpkins, etc).

**Supports**
None needed!

**Scaling**
This one should be able to be scaled up or down without any issues. I haven't tried it, so if you do and run into any fit problems, let me know and I'll put out some other sizes.

**Orientation**
The pot should be right side up, the lid should have the side with the square hole facing down, and the plant prints flat (doesn't matter which side is on the build plate).

**Print Settings**
.2mm layer height
15% grid infill
2 walls

**Links (some may be affiliate links)**
Filament I used for this print: [Overture Matte Black PLA](https://amzn.to/40e1SsF) & [Hatchbox Forest Green PLA ](https://amzn.to/3SgsabR)

2D Planter with Hidden Storage

2D Plant.stl

It was highly requested to release the files for this one so here it is! I've included both sizes - 2.75" and 4.5". I've also included a tabletop version in both sizes that does not have the sliding dovetail.

You'll also notice a modified version of the 2.75" command strip mount. It fits the command strips better and leaves no question as to which way you should attach it.

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the command strips and the screw holes are designed specifically for #10-12 x 1-1/4 in anchors and screws.

**Orientation**
The planter and tray should have their bottoms on the build plate. All mounts should have the sliding dovetail facing up.

**Print Settings**
.2mm layer height
15% grid infill
2 walls

**Links (some may be affiliate links)**
Filament I used for this print: [Overture Matte Light Brown PLA](https://amzn.to/3rMLiUd) & [Polymaker Matte Marble PLA ](https://amzn.to/46UUzYU)
[Command Medium Picture Hanging Strips ](https://amzn.to/3S4DFTG)
Hardware: [#10-12 x 1-1/4 in screws](https://amzn.to/3QrqTwf)

Grid Planter

Wall Grid Pot 4.5.stl

An inverted version of the test tube propagation mount.

**3 different versions:**
1. Small (screw mounted)
2. Full length (screw mounted)
3. Full length (command strip mounted)

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the test tube, the screw holes are designed specifically for #8-10 x 1 in anchors and screws, and the command strip mount is the exact size of a regular large command strip.

**Orientation**
The mounts should be upside down and the cleat should have the longer side facing down.

**Print Settings**
.2mm layer height
15% grid infill
2 walls
Monotonic top and bottom surface pattern

**Links (some may be affiliate links)**
Filament I used for this print: [Hatchbox Matte Ash Gray PLA](https://amzn.to/3F5LDUN)
[Overture Matte Light Brown PLA](https://amzn.to/3rMLiUd)
[Test tubes](https://amzn.to/48GuX3F)
Hardware: [#8-10 x 1 in anchors and screws](https://amzn.to/48HAdUP)
[Command Strips](https://amzn.to/46RlGnV)

Test Tube Propagation Mount - Inverted

Test Tube Mount Command Strip.stl

I've started propagating a lot of my plants so I made this little mount that holds a test tube! These propagation stations are super popular among plant people and sell really well. It's a quick and easy print at around 35 minutes. These smaller prints are usually big money makers as the profit margins are crazy high.

**Supports**
None needed!

**Scaling**
I wouldn't recommend scaling this one since it perfectly fits the test tube and the screw holes are designed specifically for #8-10 x 1 in anchors and screws.

**Orientation**
The mount should be upright and the cleat should have the longer side facing down.

**Print Settings**

- .2mm layer height

- 15% grid infill

- 2 walls

- Monotonic top and bottom surface pattern

**Links (some may be affiliate links)**
Filament I used for this print: [Overture PLA Matte Light Brown](https://amzn.to/45ir6XY)
[Test tubes](https://amzn.to/48GuX3F)
Hardware: [#8-10 x 1 in anchors and screws](https://amzn.to/48HAdUP)

Test Tube Propagation Mount

Test Tube Mount.stl

A shelf! It mounts to the wall using a french cleat.

I tested its load capacity with an 8 pound dumbbell and it didn't budge. It's very sturdy but I'd still recommend displaying lighter items on it. For reference, the heaviest ceramic vase I have is 1lb 10oz, so most items that will fit on this shelf should be fine.

**Supports**
None needed! You could use supports on the back of the shelf on the bottom of the french cleat opening, but they're not necessary. That area will bridge just fine. It might not be the cleanest bridge, but it's the back and won't be seen once the shelf is mounted.

**Scaling**
I wouldn't recommend scaling this one since the screw holes are designed specifically for #10-12 x 1-1/4 in screws.

**Orientation**
The shelf prints upside down and the cleat should be printed with the wider side facing down.

**Print Settings**
.2mm layer height
10% grid infill
4 walls
Monotonic top and bottom surface pattern

**Other Info**
I've also included the mirror image of this shelf. Would be great to use both versions on a display wall.

**Links (some may be affiliate links)**
Filament I used for this print: [Overture PLA Matte Light Brown](https://amzn.to/3PuQHIn)
Hardware: [#10-12 x 1-1/4 in screws](https://amzn.to/45ZW73w)

I've also included the 3MF file for this one. Let me know if that's helpful!

Asymmetric Shelf

Asymmetric Shelf.stl

Ya'll know I like designing things that you can mount on your wall so I sliced off the back of this bad boy and added a french cleat.

**Supports**
None needed! You could put a support on the back of the vase where the angle of the french cleat starts, but it bridges really easily. I didn't use supports and it turned out super clean as you can see in the photo above.

**Scaling**
I wouldn't recommend scaling this one since the screw holes are designed specifically for #10-12 x 1-1/4 in screws. You may be able to scale it up slightly, just make sure you leave enough material for the head of the screw to grab onto.

**Orientation**
The vase sits upright and the cleat should have the longer side facing down.

**Links (some may be affiliate links)**

- Filament I used for this print: [Overture PLA Matte Light Brown](https://amzn.to/3PuQHIn)

- Hardware: [#10-12 x 1-1/4 in screws](https://amzn.to/45ZW73w)

Wave Vase - Wall Mounted

Wave Vase - Wall Mounted.stl

The second in a series of vases! This one with a more mid century form.

No supports needed. Easy print. Can be scaled up or down however you like.

MCM Vase

The first of a series of vases I've been working on!

No supports needed. Easy print. Can be scaled up or down however you like.

Wave Vase.stl

Similar to the connected planter, but smooshed together.

No supports needed. Very easy print. If you're printing in one color, all three objects can be printed at once.

Overlapping Planter

Overlapping Short Pot.stl

I've been wanting to design planters that house multiple plants for a while now so here's the first one!

It prints in 3 parts: the base, short planter, and tall planter.

The base has little pass throughs that allow you to see when water is draining and give it open air to evaporate into.

No supports needed. Very easy print. If you're printing in one color, all three objects can be printed at once.

Connected Planter

Connected Base.stl

I've heard a lot of people are using these as a place to hide keys, valuables, etc. So I figured I'd design a version that is more suited for hiding stuff! If you're using a fake plant, the pot doesn't need to be nearly as deep, leaving more room for hidden objects.

Print settings are exactly the same as the regular Poppy. No supports needed.

Secret Stash Planter - The Poppy

Secret Stash Poppy Pot 2.5.stl

Here's the wall mounted version of the Square Wall Poppy!

Two sizes included - 2.75" and 4.75" (same sizes as the tabletop version)

I made the Command Strip mount for the 4.75" size square to match the shape of the planter. The circular mount from the round version fits too.

The 4.75" size is fairly large, so the pot, tray, and command strip mount need to be printed separately unless you have an extra large bed.

Prints without supports.

Square Wall Planter - The Poppy

Square Wall Poppy Pot 4.75.stl

This is probably the most simple shape I've designed but it's one of my favorites so far! It's pretty safe, meaning it could blend in to any home's decor, but the twist lock drip tray sets it apart.

It prints in 2 parts, the pot and the base. No supports needed.

Simple Vase with Removable Drip Tray

Simple Vase Base.stl

A square, tabletop version of the Poppy! It uses the same twist lock drip tray design as the original.

Prints without supports.

Square Poppy Planter

Square Poppy Pot 2.75.stl

A smaller version of the Tilt Lamp!

This size is great for bedside tables or bookcases and should fit on smaller printer beds.

Dimensions:

Base - 4.5"w x 5.25"h

Shade - 7"w x 6"h

Two important notes that are in the original post but I'll reiterate them here:

1. I highly recommend printing the shade using a concentric infill pattern. This will hide the infill when the light shines through it.

2. Note that you must only use LED bulbs (9 watts max) as traditional bulbs can get pretty hot and could cause damage to the plastic. I like these multi color smart bulbs that I can control with my phone, but any standard 9W LED bulb will do.

Tilt Lamp - Small

Small Tilt Lamp Base.stl

My first foray into lighting! This was a fun one.

The lamp prints in two parts, the lamp base and the shade. Supports are needed on the base for the shoulder that holds the pendant light socket in place, as well as the opening for the cord.

Important! I highly recommend printing the shade using a concentric infill pattern. This will hide the infill when the light shines through it.

The pendant light can be found on Amazon here: https://www.amazon.com/gp/product/B07ZW13PJX/

You can also find them on Alibaba in bulk for cheaper.

The pendant light includes a locking ring that secures it to the base. To install, just insert the socket up through the bottom of the base, and screw on the locking ring to clamp it in place.

Note that you must only use LED bulbs (9 watts max) as traditional bulbs can get pretty hot and could cause damage to the plastic. I like these multi color smart bulbs that I can control with my phone, but any standard 9W LED bulb will do.

Tilt Lamp

Large Tilt Lamp Base.stl

I got lots of requests for a version of this planter that was renter friendly so this is what I came up with!

It attaches to the wall using a medium 3M Command Strip and a sliding dovetail. There's a screw mounted sliding dovetail in the files as well.

Another huge improvement - I ditched the threads on the drip tray and went a twist lock design, similar to the way reusable filament spools lock together. This method will hold up better over time, is more secure, and doesn't leave any gaps between the drip tray and the pot.

I've included a 4.5 inch version as well and will be adding a 6.5 inch size soon. Note that the only the 2.75 inch size includes that 3M Command Strip mount.

The screw mounts were designed to mount to the wall using #10-12 x 1-1/4 in screws with plastic anchors. These can be found at any hardware store or online.

Wall Planter with Sliding Dovetail - The Poppy

Twist Lock Poppy Pot 2.5.stl

This planter has a hidden drip tray that twists off. It prints fast and without supports. In order for this to print without supports, the pot needs to be printed upside down.

There are 3 sizes included: 2.5", 4.5", and 6.5"

Planter with Twist-Off Drip Tray - Bubbles

Bubbles Pot 4.5.stl

Prints with no supports.

The legs need to be glued in to the base. I typically use Weld-On and a syringe to attached the legs but super glue works too!

Planter with Legs - The Nelson

Nelson Pot 2.5.stl

This is a square version of the original Poppy. The drip tray is secured to the pot with magnets! Glue the magnets in however you like, I use a little drop of super glue and a few drops of Weld-On.

Use 10 x 2.6mm magnets (2.3mm thick works too. The recess is 2.794mm deep). You can find the magnets on Amazon here: https://a.co/d/6vz5nuU

Magnetic Drip Tray Planter - Square Poppy

Square Poppy Pot 2.5.stl

Prints with no supports. I recommend using brims for the legs.

3 sizes included — 2.5", 4.5", and 6.5"

The legs need to be glued in to the base. I typically use Weld-On and a syringe to attached the legs but super glue works too!

Planter with Legs - The Ellwood

Ellwood Pot 4.5.stl

Planter with Legs - The Lloyd

Lloyd Pot 4.5.stl

Prints with no supports

3 sizes included — 2.5", 4.5" and 6.5"

Planter with Drip Tray - The Clifton

Clifton Pot 2.5.stl

Prints with no supports.

Two versions available: One for wall mounting and the other is for macrame.

Note: This was designed to mount to the wall using #8-10 x 1 in screws with plastic anchors. These can be found at any hardware store or online.

Wall Mounted Planter - The Ira

Ira.stl

A mini version of a classic mid century plant stand.
Prints fast with no supports.
4 sizes included: 1.25". 2.5" 4.5", and 6.5"

Classic Planter with Drip Tray and Stand

Classic Pot 2.5.stl

A planter with a hidden, twist off drip tray.
No supports needed.

Planter with Hidden Drip Tray - The Poppy

Prints with no supports.

This was designed to mount to the wall using #10-12 x 1-1/4 in screws with plastic anchors. These can be found at any hardware store or online.

Wall Mounted Planter - The Heywood

Heywood Pot 4.5 No Drainage.stl

Heywood 6.5 Drainage.stl

Heywood 6.5 No Drainage.stl

Heywood Wall Mount 6.5.stl

Ira for Macrame.stl

Command Strip Wall Mount 2.5 Looser Fit.stl

Command Strip Wall Mount 2.5.stl

Sliding Dovetail Wall Mount 2.5 Looser Fit.stl

Sliding Dovetail Wall Mount 2.5.stl

Twist Lock Poppy Tray 2.5.stl

Twist Lock Wall Poppy Pot 2.5.stl

Command Strip Wall Mount 4.5.stl

Sliding Dovetail Wall Mount 4.5.stl

Twist Lock Poppy Pot 4.5.stl

Twist Lock Poppy Tray 4.5 v2.stl

Twist Lock Poppy Tray 4.5.stl

Twist Lock Wall Poppy Pot 4.5.stl

Hi! My name is Brian and I design home goods and other objects for 3D printing. I started designing physical things in 2016 when I opened a custom furniture studio here in Cleveland, Ohio. I love woodworking, but through this experience, I learned what I'm really passionate about is designing products. So in 2018, I bought my first 3D printer and quickly became infatuated with it.

I like designing things that people are willing to proudly display in their homes. Most of my designs tend to fall under mid century modern, contemporary, and bohemian styles.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

HendricksDesign

Pinned models

Wall Mounted Planter - The Ira

Wall Planter with Sliding Dovetail - The Poppy

MCM Vase

Monstera Leaf Magnet

Cleo Lamp

Big Bubbles Planter

Mini Magnetic Vase No. 2

Mini Magnetic Vase No. 1

Simple Cup Planter

2D Planter with Hidden Storage

Grid Planter

Test Tube Propagation Mount - Inverted

Test Tube Propagation Mount

Asymmetric Shelf

Wave Vase - Wall Mounted

MCM Vase

Wave Vase.stl

Overlapping Planter

Connected Planter

Secret Stash Planter - The Poppy

Square Wall Planter - The Poppy

Simple Vase with Removable Drip Tray

Square Poppy Planter

Tilt Lamp - Small

Tilt Lamp

Wall Planter with Sliding Dovetail - The Poppy

Planter with Twist-Off Drip Tray - Bubbles

Planter with Legs - The Nelson

Magnetic Drip Tray Planter - Square Poppy

Planter with Legs - The Ellwood

Planter with Legs - The Lloyd

Planter with Drip Tray - The Clifton

Wall Mounted Planter - The Ira

Classic Planter with Drip Tray and Stand

Planter with Hidden Drip Tray - The Poppy

Wall Mounted Planter - The Heywood