Straighten out your workshop with Gridfinity modular storage - deploy these plates anywhere you need some order!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Frame: https://a360.co/3ccHbsg
- Weighted Plate: https://a360.co/3uCJ2gR

The foundation of every Gridfinity setup is a baseplate, and these let you drop storage where you need it most.

**Frame**: The absolutely minimal no-frills baseplate. No room for screws or magnets, but saves filament and headroom. If your storage unit is on a steel surface, you can still put magnets in the storage blocks to keep them from sliding.

**Weighted**: Heavy, sturdy baseplate perfect for desktops, shelves, and other places where knocking stuff over is a big problem. 

Secure blocks permanently with [M3 screws,](https://amzn.to/37IaXTg) or temporarily with [6x2mm magnets](https://amzn.to/37Ihopq). Add [rubber feet](https://amzn.to/3LZv4v5) to keep the whole shebang from sliding, and [metal tire weights ](https://amzn.to/3uAzH9f)to drop the center of gravity and prevent wipeouts. You don't need to install every magnet, foot, and weight! Just use enough for your needs.

A Prusa i3 Mk3 can print up to a 5x5 grid. No matter what you use, make sure your bed adhesion and release is dialed in - these love to curl, and their high surface area can make them challenging to remove.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider plates can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Baseplates

Weighted Baseplate 3x2.stl

Frame 1x4.stl

Frame 1x5.stl

Frame 1x6.stl

Frame 1x7.stl

Frame 2x2.stl

Frame 2x3.stl

Frame 1x2.stl

Frame 1x3.stl

Frame 2x7.stl

Frame 3x3.stl

Frame 3x4.stl

Frame 3x5.stl

Frame 3x6.stl

Frame 3x7.stl

Frame 4x4.stl

Frame 4x5.stl

Frame 4x6.stl

Frame 4x7.stl

Frame 5x5.stl

Frame 5x6.stl

Frame 5x7.stl

Frame 6x6.stl

Frame 6x7.stl

Frame 2x5.stl

Frame 2x6.stl

Weighted Baseplate 1x3.stl

Weighted Baseplate 1x4.stl

Weighted Baseplate 1x5.stl

Weighted Baseplate 1x6.stl

Weighted Baseplate 1x7.stl

Weighted Baseplate 2x2.stl

Weighted Baseplate 1x1 (super cute).stl

Weighted Baseplate 1x2.stl

Weighted Baseplate 2x4.stl

Weighted Baseplate 2x5.stl

Weighted Baseplate 3x6.stl

Weighted Baseplate 3x7.stl

Weighted Baseplate 4x4.stl

Weighted Baseplate 4x5.stl

Weighted Baseplate 4x6.stl

Weighted Baseplate 4x7.stl

Weighted Baseplate 5x5.stl

Weighted Baseplate 5x6.stl

Weighted Baseplate 5x7.stl

Weighted Baseplate 6x6.stl

Weighted Baseplate 6x7.stl

Weighted Baseplate 7x7.stl

Weighted Baseplate 2x7.stl

Weighted Baseplate 3x3.stl

Weighted Baseplate 3x4.stl

Weighted Baseplate 3x5.stl

Versatile open-top storage blocks for the Gridfinity modular workshop storage system - multiple sizes for infinite options!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: https://a360.co/3vbu9B5

These are perfect for storing small parts and long, thin objects like needle files, and you can stack them as high as you want! The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different sizes and divider counts, to give you OPTIONS! Note that none of the compartment sizes overlap - there isn't a two-compartment 4x1 bin because you can just use two one-compartment 2x1 bins.

Dimensions in file names are Width x Depth x Height. Width and Depth units are 42mm grid slots, Height is in 7mm units. A Prusa i3 Mk3S can fit a five-unit-wide bin on its plate.

Note that two-unit-high bins don't have labels - they would cut too far into the usable storage area.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. Wider bins can curl, so maximize your bed adhesion if you're going big!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Divider Bins

Divider Box 2x1x6 5-Compartment.stl

Safely grab the right tool with the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at https://www.youtube.com/watch?v=ra_9zU-mnl8
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Nipper Holder: https://a360.co/37jchw3
- Stripper Holder: https://a360.co/3Erq2oV

These racks pack tons of hand tools into a small area, positioned so you can safely see and grab the business ends. These work great for nippers, flush cutters, wire strippers, pliers, scissors, crimpers, nibblers, cutters, and punch-down tools.

*These storage blocks are extra-big and tend to curl! Use a brim and ensure good bed adhesion.* 

**Nipper Holder**: Holds six tools about 80mm from handle to handle. If the tool is spring-loaded, the undercut will keep it from falling out. This can be mounted sideways to store five tools.

**Stripper Holder**: Holds two wire strippers or other long, slim hand tools up to 18mm thicc. I've prepared two sizes - 200mm is your usual multi-hole wire stripper, and 160mm fits many crimpers and termination tools. Both should fit on most printers.

**Gridfinity Tips!**
- Use any filament with an 0.6mm or smaller nozzle. 
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Nippers + Strippers + Pliers Racks

Nipper Holder x6.stl

Pointy boi storage for the Gridfinity modular workshop storage system - saves space and delicate fingies!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Pick Rack: https://a360.co/3JCOrIS
- Chonk Rack: https://a360.co/3xgYhO9
- Tweezer Rack: https://a360.co/3uxC0dd

These racks store long, pointy objects at an angle... but angle the business ends away from pokey fingers.

These are all two-part models. Print an Upper and a Lower and glue 'em together.

- The Pick Rack is perfect for slender tools like picks and files.
- The Chonk Rack is for thiccer tools (hey-o) like scrapers, forceps, and spring tweezers.
-  The Twizzles Rack holds tweezers. I call them twizzles because I think it's funny.

The Twizzles Rack Upper is the only piece that needs support.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Pick + Tweezer Racks

Illustration! Don't print!!

3D printing accessories for the Gridfinity modular workshop system - store tools, nozzles, and more!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Caddy: https://a360.co/3KzVx2a
- Bottle Holder: https://a360.co/3LVjAsC
- Magigoo Holder: https://a360.co/3KzVEe6
- Nozzle Holder: https://a360.co/3KxGS7y
- Volcano Nozzle Holder: https://a360.co/3JLhKJz
- Revo Nozzlebreak Holder: https://a360.co/3xmVPpk
- Glue Sticc Holder: https://a360.co/3vapCiq

This assortment of 3D printer organizers is perfect for printing what you love to print - accessories for your printer!

**3D Printer Caddy**: Puts emergency supplies within reach! Holds scraper, nippers, tweezers, acupuncture needles, brass brush, adjustable wrench, and nozzle wrench

**Bottle Holder**: Designed to hold Nano Polymer high-temperature bed treatment, but also fits many small spray bottles. Bottles should not shake loose.

**Dual Bulk Nozzle Holder**: Holds eight copies of two different nozzle sizes. Can stack when loaded with E3D or Creality-style nozzles.

**Quad Revo Holder**: Holds four E3D RapidChange Revo nozzle-heatbreak nozzlebreaks. Can stack.

**Triple Volcano Holder**: Holds three extended E3D-style holders, like those included with the Anycubic Vyper and Kobra. Can stack.

**Glue Stick Holder**: Holds multiple sizes of icky sticky horsey bois, particularly Elmer's small and regular, and Kores.

**Magigoo Holder**: Holds four-piece Magigoo bed treatment assortment pack, and should not allow them to jiggle loose.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity 3D Printing Bundle for Nerds

3D Printer Caddy.stl

Pen, pencil, and marker storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Regular Version: https://a360.co/37EP2we
- Chisel Version: https://a360.co/3E49liU
- EXTRA THICCCCCC: https://a360.co/3jqmzx4

These holders were designed to securely store Sharpie markers, but should fit many other brands of markers and other roughly marker-shaped objects. I won't judge, you do you.

These are tall enough to keep the pens from falling out, but securing with magnets or screws is **strongly** recommended!

**Regular version**: Fits standard Sharpie markers and other round, slim objects with a diameter of 12mm or less, like brushes and test tubes.

**Chisel version**: Fits chisel-tip Sharpies, paint pens, and other stuff with a cross-section that fits a 16x22mm ellipse.

**Magnum version**: Fits the girthiest of Sharpies and other extra-thicc 27mm rods. Careful where you point that thing.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Pen, Pencil, and Marker Holders

Sharpie Holder, Chisel.stl

Stash your measuring bois on your Gridfinity modular workshop storage system, Excalibur style.

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3KZAXs6

This holder stores a Mitutoyo Absolute Digimatic Series 500 caliper and a pair of SR44 batteries in a bare minimum of desk space. By sticking the caliper straight up, the contoured socket protects the jaws from damage and fits 6", 12", and all sizes.

This block has a high center of gravity, so I strongly recommend mounting it to [a weighted baseplate](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%20Baseplates-60925?manualModelView=true) using magnets or screws!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Caliper Holder

Glass-front open-top storage blocks for the Gridfinity modular workshop storage system - yes, real glass!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3v8mtzG

These modified divider bins have one wall replaced with a glass microscope slide! Glass is more scratch-resistant than acrylic, and microscope slides come pre-cut to size. 

Each bin is made of two parts, the Compartment and the Faceplate. You'll also need:
- 1x3" Microscope slides: https://amzn.to/3O6qjBO
- 2mm Repair Tape: https://amzn.to/3M1D9zF

How to assemble:
1. Apply two strips of tape to the microscope slides, touching the short edges.
2. Stick that slide to the faceplate.
3. Apply two strips of tape down the short sides of the faceplate, over the glass.
4. Apply a third strip along the bottom. It will curl a little around the bottom.
5. Slap that crap onto the divider bins. Press hard.

These are perfect for storing small parts, especially if you plan to stack 'em up. The big window makes it easy to check what's inside and monitor your supply levels.

The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different divider counts, to give you OPTIONS! Because microscope slides are only available in one size, only 2-unit-wide bins are possible.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. 

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Window Divider Bin

Window Box 2x1x6 3-Compartment.stl

Socket organizers and ratchet holders for the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- 1/4" Imperial holder: https://a360.co/37cdZPW
- 1/4" Metric holder: https://a360.co/3vgUAFq
- Mulwark ratchet holder: https://a360.co/3OiHhNJ

These holders store your socket sets and ratchet drivers. They orient the tools to make them easier to find and grab the bit you need!

**1/4" Imperial and Metric Holders**: Designed for Harbor Freight 10-piece 1/4"-socket kits, but should fit many others.

**1/4" Universal Holder**: Has ten 20mm-diameter slots. Note that this is five slots wide, while the Imperial and Metric versions are four slots wide.

**Mulwark Holder**: Fits the [Mulwark-brand low-profile ratchet driver](https://amzn.to/3v6BPEw), the 20pc bit kit, and has slots for 13 more hex bits. I strongly recommend buying the bit kit - a low-profile ratchet needs low-profile bits!

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners!

Gridfinity Ratchet + Socket Holders

Socket Holder, Metric, Non-Stackable.stl

Socket Holder, 0.25in, Universal, Non-Stackable.stl

Maker-favorite screwdriver storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- ES121 Holder: https://a360.co/3KLQziI
- Gen 1 Holder: https://a360.co/3rj30Li
- Gen 2 Holder: https://a360.co/3jxCNVb

These holders store the popular, high-quality iFixit Mako screwdriver kit, the old-skool iFixit screwdriver set, and the ES121 open-hardware electric screwdriver. Open-source screwdriver, what a time to be alive.

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity iFixit Mako + ES121 Screwdriver Holders

iFixit Driver Set Gen 2 Holder.stl

__3D printed filament dry box__


An enclosure for one spool of filament featuring desiccant cages and hygrometer for reducing and monitoring moisture on hygroscopic filament. Rewind system with locking mechanism for when the spool is not in use. Check out [the videos](https://www.youtube.com/watch?v=rsfHs_I52mk&list=LLMvNnP9oAQl5IApL8XBQIkQ)!

Make sure to check the advantages and disadvantages first, and follow instructions on [the project page](https://mihaidesigns.com/drybox/).

__Printing:__
>* Print one base (filename starting with "print one base.")
>* Print one lid (filename starting with "print one lid.")
>* Print all 40 shared files (some are identical)


DXF files included for laser cutting windows.


See the [BOM list](https://docs.google.com/spreadsheets/d/1ia3ImaCrxpdLvES7OI8j2lGvnmtfEvpncn1Ds7_c1f0/edit#gid=0) for required parts.

Licensed under CC https://creativecommons.org/licenses/by-nc-sa/4.0/


If you like my projects, you can support my work on [Patreon](https://www.patreon.com/mihaidesigns)! 😎

No supports needed, supportless, FDM.

Mihai's DryBox

pick one base. front and side angled windows (default).stl

front_panel.dxf

side_panel.dxf

__This is the new version V3, of Marsgizmo Filament Bunker__

This is a solution to keep your 3D Printing Filaments dry.
It is designed for 3D Printing.

Please ignore the wrong part names (currently not possible to rename them). 
After download, you'll get the correct parts and names.


This new version is compatible with both containers (Narrow and Wide).

__Check the added pictures for more details__


See the quick assembly in [my video](https://youtu.be/Es-HM-d71WA)
Here's also the [previous video] (https://youtu.be/w2T6HxC_8cE)

____________________________

__What do you need to make it?__

For each individual Filament Bunker, you need (more details below):
> 1 x cereal container
> 4 x bearings
> 1 x about 50cm (20”) of PTFE tube
> 1 x PTFE connector (for 4mm OD PTFE tube)
> 50 grams (1/2 cup) of Silica beads
>  1 x Hygrometer
> 3D Printed Parts (1 x Main Body, 1 x Silica Lid, 1 x Cylinder 1 and 1 x Cylinder 2). No supports needed for printing.


____________________________

__Where to buy the additional parts?__
The following are my affiliate links.

There are 2 cereal containers (Narrow and Wide), check the above video to distinguish the differences:
> Narrow Container: with big handgrips can hold Spools of 60mm width and 200mm in diameter (usually 750g Spools) 
Get them from here (not available in all countries): [link] (https://geni.us/pSLAo)


> Wide Container: can hold Spools of 68mm width and 200mm in diamerter (usually 1Kg Spools, e.g. Prusament, etc.).
Get them from here (not available in all countries): [link] ( https://geni.us/nrcXpYG)


The volume of both containers is 4 liters (16.9 Cups, 135.3oz).
DO NOT GET the smaller versions!


Using regular 608 ZZ (or 2RS) skateboard bearings: 
> pack of 10: [link] (https://geni.us/uLMvbQ)
> or pack of 100: [link] (https://geni.us/OiChoH)



PTFE tube and connectors. I recommend 3mm ID / 4mm OD, but you can also use regular 2mm ID / 4mm OD
(ID - Inner Diameter, OD - Outer Diameter)
> 3mm ID / 4mm OD: [link] (https://geni.us/NIfXBG4)
> 2mm ID / 4mm OD: [link] (https://geni.us/4YjDen)
> PTFE M10 Connector: [link](https://geni.us/JQRSNXl)

Silica Beads: 
> the best are Molecular Sieve beads [link] (https://amzn.to/3jljvU9)
More details about [which method is the best](https://www.sorbentsystems.com/desiccants_charts.html)
> silica beads with no markers: [link] (https://geni.us/ktHdsU)
I recommend using silica with no color markers, the ones which are blue or orange are [slightly toxic](https://en.wikipedia.org/wiki/Silica_gel)

Hygrometer (the square version, not round): [link] (https://geni.us/gAhF3)
Dimensions: 46mm x 27mm / 1.81 x 1.06 inch.



____________________________
__Printing details:__

> - no supports needed!
> - can easily be printed from PLA (try to use quality PLA), otherwise go with PETG.
> - 0.2mm layer height for better quality, but also 0.3mm layer height works fine (lower quality)
> - 3 perimeters (for strength)
> - 100% infill (there’s a very tiny difference in overall quantity)
> - you need in Total around 67 grams on PLA, for one complete set.
> - you can print is on small beds like Prusa Mini 18x18cm (you only need to rotate the Main Body 45 degrees)
____________________________

__Check my other videos:__

[my Youtube channel] (http://youtube.com/marsgizmo)
[my Instagram channel](https://www.instagram.com/marsgizmo)



____________________________
License Type = CC BY-NC-SA 
(CC Attribution-NonCommercial-ShareAlike)
[marsgizmo](https://www.marsgizmo.com)

marsgizmo Filament Bunker V3

__ This is the Main Body for the marsgizmo Filament Bunker__
It is designed for 3D Printing.

> 👉 [check it here in my video]()

[my Youtube channel] (https://www.marsgizmo.com)
[my Instagram channel](https://www.instagram.com/marsgizmo)

____________________________
__3D Print Settings:__


____________________________
License Type = CC BY-NC-SA 
(CC Attribution-NonCommercial-ShareAlike)
[marsgizmo](https://www.marsgizmo.com)


Main Body v5.stl

Marsgizmo Filament Bunker v3 - Cylinder 2.stl

This Lightsaber has a removable collapsing blade that can be printed separately in a different color. The hilt is designed with a screw on cap which allows the blade to be inserted after its printed. The hilt is 209mm long with the cap installed but it expands to over 950mm in total length with the collapsing blade installed! 

Its designed to be printed with a ,4mm nozzle, with a line thickness of .43, so the blade will be two shells thick. The test print can be found [here.](https://thangs.com/3dprintingworld/SwordSaber-Test-Print-23601)

**Links to the filament I used(aff):**
[Galaxy Black](https://amzn.to/3Cu2xKt)
[Lipstick Red](https://amzn.to/3jH1Fti)

**Video**
[Intro](https://youtu.be/xN0H9npkkP4)
[Troubleshooting](https://youtu.be/YQV4PYJPhx0)


**Collapsing Lightsabers**
[ROTJ Single Extrusion]( https://thangs.com/3dprintingworld/Collapsing-LightsaberPNP-23596)
[ROTJ Dual Extrusion]( https://thangs.com/3dprintingworld/Collapsing-Lightsaber-Dual-Extrusion--34803)
[Vader’s Dual Extrusion]( https://thangs.com/3dprintingworld/Collapsing-Sith-Lightsaber-dual-extrusion-28319)
[Leia’s Dual and Single](https://thangs.com/3dprintingworld/Leias-Dual-Extrusion-Collapsing-Lightsaber--25509)
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models, consider joining my [Patreon](https://www.patreon.com/3dprintingworld)


Collapsing Sith Lightsaber

COLLAPSING-LIGHTSABER-SITH.stl

Mount storage right to your printer with the Gridfinity modular workshop storage system - whatever machine you use!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Anycubic Sidecar: https://a360.co/3xonYw4
- Anycubic Top: https://a360.co/3jy22GN
- Lulzbot: https://a360.co/3xobNzx
- Prusa: https://a360.co/3Jzfp47
- Snapmaker: https://a360.co/37Om65m
- E3D Toolchanger: https://a360.co/3rlmn6K

These brackets mount to your 3D printer and allow you to put Gridfinity storage blocks right where you need them! These work especially well for the [Gridfinity 3D-printer accessory kit](https://bit.ly/3jtTfWu).

If you need more adjacent slots, just print multiple baseplates and butt them up against each other. *I STRONGLY recommend magnets or screws so you don't knock stuff into your printer!*

**Anycubic Vyper/Kobra**: Also fits any printer made of extrusion with 6mm slots. Mount to your printer's frame with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD!

The **sidecar** baseplate mounts to the base frame, parallel with the floor, a lot like the included filament holder. The **top-mount** baseplate mounts on the Z axis crossbeam or base frame. *Make sure the gantry, extruder, and plate don't collide with your Gridfinity!*

**Lulzbot**: Fits the upward-facing edges of the top crossbars. This one is a real pain in the butt to install.

**Prusa**: Slides on over the steel frame, no fasteners required. *THE BASEPLATE AND EXTRUDER MUST BE ON OPPOSITE SIDES OF THE FRAME!*

**Snapmaker**: Mount to the optional enclosure with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD! I didn't make one for the printer itself, sorry!

**Toolchanger**: Mount to the top of the printer with three button head M3x5 screws. *Don't use longer screws! They won't fit!*

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Printer-Mounted Baseplates

Anycubic Baseplate, Sidecar.stl

It's the Torture Toaster!  The guys at Edge of Tech challenged me to make a torture test that would be fun and interesting, and this ridiculous thing is where I ended up :)  This will test your print tolerances, overhang handling, and most of all, your bed adhesion!  No supports required, though!  It's not as torturous as it sounds, though, and with a little perseverence you'll get it printed! :D

Find more of my stuff (and support me!❤) at https://www.patreon.com/clockspring3D

Find Edge of Tech at:  https://youtube.com/theedgeoftech


Clockspring3D Torture Toaster

I designed my own 20mm x 20The Images are from a print on my Ender 3.
mm x 20mm Calibration Cube in Tinkercad so I had my own test print for reference.
I call it the CHEP Cube.
It’s become a popular print for many people and it’s fun to see where it turns up.

CHEP Cube

CHEPCube.stl

Mechanic? Auto Tech? Car Enthusiast? Well I FOUND THE **10MM**! It was hiding in my 3D Printer!  

This 12oz Can Cup design is inspired by a 10mm Shallow socket.  The Handle equipped version is designed to mimic a **10mm** Combination wrench with open and Box ends (that actually measure 10mm).  The cup body features a hex design in the can opening, a square "Drive" hole in the bottom for can removal, and a #10 inset into the side.  

Perfect for the Car / Tool Enthusiast in your or your life! Thanks to TikTok Live chat for the idea on this one!

Designed for cans with a 66mm Diamater. Cup measures 111mm tall.

-------------------------------------------------------------------

- **INCLUDED FILES:**
  - CAD STEP File to learn how I designed these.
  - 10mm Can Cup with Wrench Handle
  - 10mm Can Cup without Handle

-------------------------------------------------------------------

- **PRINT PARAMETERS:** 
  - Supports Required between bottom and top of handle.
  - 3 Perimeters Recommended.
  - 15%+ Infill Recommended (I Prefer Rectilinear)

Mine was printed in Inland Grey PLA+.

-------------------------------------------------------------------

Check out my other novelty Can Cup designs and more here on Thangs!

Want to Support what I do? Check out my social medias please!

**LinkTree:** http://www.HotRodHippie.com/links

--------------------------------------------------------------

**All of my Designs are covered by a Creative Commons Non-Commercial LIcense.**  Sale of prints using my designs are the sole right of myself, the designer, and those I license to do so. Please understand every design is hours of work and multiple prototype prints to ensure quality.  Unauthorized sales will result in new designs not being made public.

PLEASE Credit any and all Remixes of my designs: MandicReally

10mm Shallow Can Cups - 12oz Soda Pop Can Cups

CAD STEP File of the Designs for Educational Purposes.

PLEASE Credit any Remixes: MandicReally

10mm Cups.step

CNC bit storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Jewel Case: https://a360.co/3Jw4Bnd
- Bulk Holder: https://a360.co/37IQCgV
- Tubes: https://a360.co/3rFWH4X

These holders securely store CNC tools, drill bits, and other things with 1/8", 1/4", and 3mm shanks.

The 1/8" and 1/4" Bulk versions hold up to 77 and 21 bits, respectively. These point the bits straight up, so you can't stack on top! Be careful not to hurt yourself!

The Tube version holds 12 bits in their protective packages. You can stack other blocks on top of this.

The Jewel Insert version holds four detachable sleeves from snap-together jewel case packaging. These usually hold 10 bits. You can stack other blocks on top of this.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity CNC Tool Holders

CNC Tool Holder, Tubes.stl

HT-FRT adapted for milspec lowers.  Every part has been updated.

For a basic milspec lower with the sear block hump above the standard safety, print these files:
    1_block - wide - remix.stl
    2_plate - remix.stl
    3_safety - mirrored_2x_wide - remix.stl
    4_pin.stl
    
If your lower does not have the sear block hump and you want a bit more engagement, print these instead of their reciprocal above:
    1.1_block_wide - remix.stl
    3.1_safety - wide - remix.stl
    4.1_pin.stl
 
Use a spare Bolt Catch Spring.

This requires a milspec lower, a "milspec" semi-auto FCG, and a 'standard' full-auto BCG.  The 'plate' file will replace the disconnector and disco spring.

I printed these with eSun PLA Pro, but any quality PLA+/Pro should be fine.  Use a high number of perimeters, and high percentage of infil (grid, lines, rectilinear, or similar).  I used 6 perims and 60% line infil.

If your BCG is stiff to pull back, it is dragging on the hammer because the plate is slightly too tall, and doesn't allow the hammer to retract far enough.  Referencing [plate_adjust.png](https://i.imgur.com/OLunfE5.png), file or sand a *little* bit off in the red area, test fit, and repeat until the BCG doesn't drag.


CC BY-SA

HT-FRT milspec remix

1_Block - wide - remix.STL

1.1_Block_-_wide_-_remix.STL

3.1_Safety_-_wide_-_remix.STL

1.1_Block_wide_remix.step

3.1_Safety_wide_remix.STEP

3_Safety_-_mirrored_2x_wide_-_remix.STL

3_Safety_mirrored_2x_wide_remix.STEP

Designed to work with storage modules from the Gridfinity system by Zack Freedman.

These racks are stackable, with small tabs to aid in both horizontal and vertical alignment.

I had these windowed divider bins in mind when i was designing this: https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Window%2520Divider%2520Bin-60754


Gridfinity Wall Rack

rack.step

Functional

Categories

Popular

Personalize

Trending