A small bundle featuring both the Raccoon Flexi and Happy Dumpster!

Raccoon and Dumpster

Its an 8 bit axolotl or a Bloxlotl!

I have included a tadpole version as well as prepainted 3MF files!

These guys make great end of roll savers, I also print them as purge objects ( 50% rectilinear works best to eat up the most waste using bambu slicer)

Tested down to 80%

The big green yellow guy is 220%, the purple teal are 100% and the yellow spruce tads are 80%

Make sure you have good amount of infill to supports the top layers! I personally use 15% grid on the bambu slicer!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
No supports! I only used supports on the 220% one just so the eyes don’t droop! I used the normal default supports in bambu slicer, make sure you enable “on buildplate only”

Bloxlotl Flexi

Bloxltol_Flexi_v3.stl

A happy little dumpster! 

There are two versions:
A complete print-in-place version and a print face features seperatly version! 
This model is easy to print in multi color without having a multi color printer! The dumpster can be printed in two colors by manualy switching the filament just after the lids are done printing to get different color lids! 

The inside the the dumpster is beveled so that it can be printed in place and without supports! 

Tested down to 50% as pictured with the teal and brown lid mini dumpster

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon patreon.com/Layersingreen

Happy Dumpster

dumpster_Complete.stl

Silly little raccoon friends!

These little guys make fun fidgets just make sure you keep them out of your trash 🦝

3MF Prepainted file is included!!

No supports!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
Tested down to as little as 40% and was still fully functional! but my favorite scale which you can see in the picture of the 3 coonies is 70%

If you are having adhesion issues, the raccoon prints great with a brim!

Raccoon Flexi

Raccoon_Flexi_v2.stl

Ginger bread cookies that can be baked right on your 3D printer, no oven or cooking required

Just joking dont eat them!

They are a cute little holiday set of two ginger bread cookies (with butts) They come with a sweet holiday mug to float in!

In this pack you'll find:

❄️ Ginger Bread Tushie with bow - Ornament, Sculpt, Prepainted 3MF
❄️ Ginger Bread Tushie with Hat - Ornament, Sculpt, Prepainted 3MF
❄️ Holiday Mug - Sculpt and Prepainted 3MF

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
Recommended settings:

For the Ginger breads I recommend adding a brim especially so if you are printing them in multicolor. Their build bed contact area is small compared to how tall they are which makes them susceptible to being knocked out of place by the nozzle. Adding a brim gap of 0.1-0.2 mm will make it easier to remove.

100% ginger bread fits in a 100% Mug

No supports for any of the files

GingerBread Tushie

GingerBreadTushie_Bow.stl

The all seeing Arcadia is perched on the rock to watch over the tumbling dice!

This dice tower prints without supports, and is compatible with D20 dice!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
I recommend 3 walls, Tested to print well with as little as 5% gyroid infill.

Arcadia Dice Tower

arcadia-dicetower.stl

What Does the fox say? HueHueHueHueehuHue

Maybe not.

A little fox flexi! She prints without supports, she can even stand up, but most of all she can swipe your heart!

The fox has been tested from 60% to 150%
the painted fox in the pictures is 85% scale which was my preferred scale

I have also added a keychain version!
This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
No supports! If you are having adhesion problems she prints great with a brim!

Fox Flexi

Fox_Flexi_v2.stl

I am so very excited to share these little friends with you! This release includes 3 unique forest pixies: Mushroom Pixie, Deer Pixie, and Moth pixie

They print without supports, they are small at 100% and I don't recommend scaling them down further, but they scale up well and I particularly love them in 150% scale which is the bigger size in the pictures

Although they print well with the standard 0.2 layer height I highly recommend printing them in a lower layer height like 0.16, as this will help improve the top surfaces and the overall look! For the Z seam I had set them to print with their feet pointing towards the front of the plate and the z seam set to "back right" in cura, this keeps the z seam minimally visible,  if you are using prusa slicer you can paint the z seam up the chin or along the top curve of the eye, increasing top layers to 6 will also ensure that the top surface prints well

Forest Pixies

A little deer pixie! He carries a little leaf for goodluck!

Prints without supports! He can even stand up on his own if he gets a little help balancing his head!

Bonus Keychain and Magnet versions!

Keep him in your pocket or return him to the forest for another to find, but forever a friend you'll have!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
No supports!

I recommend printing with 0.16 Layer Height for a nicer top finish

I dont recommend printing smaller than 100% but he scales up wonderfully! 100% and 150% are displayed in the pictures.

Deer Pixie

Deer_Pixie_Magnet_5x3.stl

A moth Pixie! She is a little shy but full of magic!

Prints without supports! He can even stand up on his own if he gets a little help balancing his head!

Bonus Keychain and Magnet versions!

Keep him in your pocket or return him to the forest for another to find, but forever a friend you'll have!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
No supports!

I recommend printing with 0.16 Layer Height for a nicer top finish

I dont recommend printing smaller than 100% but he scales up wonderfully! 100% and 150% are displayed in the pictures.

Moth Pixie

Moth_Pixie_Magnet_5x3.stl

A little mushroom friend appears! He has a wiggly head, and little wiggly arms!

Prints without supports! He can even stand up on his own if he gets a little help balancing his head!

Bonus Keychain and Magnet versions!

Keep him in your pocket or return him to the forest for another to find, but forever a friend you'll have!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
No supports!

I recommend printing with 0.16 Layer Height for a nicer top finish

I dont recommend printing smaller than 100% but he scales up wonderfully! 100% and 150% are displayed in the pictures.

Mushroom Pixie

mushroom_Pixie.stl

its a spooky little skelly crab! Just in time for spooky season! This little friend is often found on the lower levels of magical dungeons in groups of two or three, or in a water cave off the coast of spooky island!

Ive included two versions - one is print in place, the other is split up into two parts for an easy way to produce a multi color print!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
Skelly crab: print in place, no supports crab! tested from 60% to 150% the purple crab is 150% the black and white one is 100% and the little pink orange guys are 75%

Skelly crab split up: You'll find two files in this one. the body and the skull section.
You will need supports to print the skull part I used default cura normal supports for mine! and it only needed very minor clean up, I then used superglue to glue to skull onto the body. The black and white crab in the pictures is printed on my ender 3 pro using the split up version!

Skelly Crab

skelly_crab.stl

This is a bat!

A bat with a bobbly head!

This pack comes with the following files:

Bat bobble head section (two variants)
Bat body section
3D printable spring for extra bobblness
Batty sculpts ( two variants)
Batty keychain

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
All of the models in this pack print without supports!

There are 3 parts, the head, the body, and the spring which should fit snuggly without needing glue! The tolerance for the spring fit into the body section will depend on your filament and printer, if you feel that it is too loose try reprinting the spring scaled 1% higher, or if you are having trouble fitting the spring in then scaled it down 1%

The spring should sit all the way into both of the spring sockets!

Important: Pulling or bending the spring will result in it being crooked and not sitting straight, when inserting the spring insert it into the head piece first I used a small screw driver to help push it snuggly into its spot (see gif), then insert the spring with the head into the body piece using a tool like a little screwdriver or anything slender that will fit in the gap to push the spring into the body slot.

Bat Bobblehead

bonus-bat-sculpt-starryeyes.stl

Meet Mizu!

This water element dragon has an awesome wing design that makes it so fun!

The wing design features fan style wings with clip on fins! this allows you to print the fins separately which gives the dragon a pop of color! It is super simple assembly with adding the extra fins on the posts and then the star fish caps just pop in place securely

The fins print horizontally which greatly decreases the risk of losing adhesion and the whole plate
This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
Important Information:

The clip on fins were made to have a tight tolerance, you must be careful when adding them to the post without using excessive force. They were made to be tight so that they can be posable. if you find yourself struggling with getting them on you can do a few things:
Using a deburring tool on the inside of the hole to increase the diameter slightly

Reprinting the fins that didn’t fit and scaling them up by 2%
Please double check the fins to make sure they were added on correctly as once the caps are on it will be difficult or impossible to get them off without damaging the posts.
The bottom fins can be distinguished by a small dot near the bottom of the fin
The top fins should go in the order of big fin first and then small fin on top
when adding the caps it is best to place them directly on top of the posts and using your palm to push them in

Scaling:
Mizu was tested down to 80% and up to 125%
I don’t recommend printing her smaller than 80%
If you found the tolerances to be too tight I recommend printing the clip on fins at 82% for an 80% Mizu

When scaling 125% and above the fins and caps should be printed 2% smaller in order to combat the increase in tolerances. This means for a 125% Mizu print the fins and caps at 123%

Water Element Dragon: Mizu

Mizu.stl

This is an Octopus but it isn't an ordinary octopus! It can spin its tentacles round and round!

The octo spinner is a small quick easy print that you can fidget with all day! And just when you though it could not get any more fun, Surprise! This little dude comes equipped with a little witchy hat, and a cauldron that it sits on top as a lid!

At 100% scale the cauldron comfortably fits a full set of D20 dice!

In this pack you will get:

Octo spinner
Octo spinner keychain
Octo spinner witchy hat
Octo spinner Cauldron

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
The octo spinner was tested to still spin as little as 80%
I don't recommend scaling higher then 200% due to the head becoming very loose and wobbly if going any higher

100% Octo spinner fits an 100% hat and 100% Cauldron, so if you are scaling them make sure you scale all of them together!

If you are having adhesion issues this little dude prints great with a brim!

Octo Spinner

octo_spinner.stl

Frogs with tushies!

Some are happy, and some are not!

In this pack you'll receive the following files:

Happy and frowny frog
Frog with mushroom cap
Frog with cranky snail friend
Happy and frowny frog keychain
Frog pot with and without drainage hole

Rest assured they absolutely all have tushies

These models are for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
There are no special settings required! All of the files in the pack print without supports!

Butt Frog Pack

Butt_Frog.stl

A fun mini dice tower! Its mossy, little mushrooms sprout from its trunk, and a hollow in which dice may roll onto a small rocky platform.

at 100% you can roll D20 dice, can be scaled down to 90% with dice still fitting

Important to note that at 100% scale the platform that catches the dice is not large enough to roll all of the dice one after the other as it s meant to be a mini dice tower for single rolls. There is however room to scale it up some

This dice tower is part of a bigger pack released on patreon, follow the link below to check out the rest of the pack!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
Prints without supports!

Wood Stump Dice Tower

TreeStump_Dicetower.stl

Meet Kosha! She is a curious mix between an axolotl and a dragon! and she is dressed in her best spring attire!

She is print in place, and without supports!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
Super easy print! No supports! Tested down to 80% I Recommend having making sure you have good bed adhesion and printing with at minimum of 3 walls.

Kosha

Kosha_short_V4.stl

They are backk!! A brand new set of butt goblins! These three come from the Magical forest and are super butty! If they don't make you sing "I like big butts" then you are definingly lying!

This pack includes:

- Blossom Butt Goblin
- Mushroom Butt Goblin
- Moth Butt Goblin
They are easy to print, fun to look at, and will be happy to be your desk mates! Yaay!!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
No special printing instructions! No supports required!

Butt Goblin Pack

Blossom_Buttgoblin.stl

A wild pug footling has appeared!

This fun little chonky dude has little feet that pop in and out! He can also stand up on his feet!

You will receive 3 files in this pack:

Pug footling
Pug footling with bow collar
Pug footling with spikey collar

The collar versions can be scaled down to 60% and be used as keychains!

no supports required!
Tested down to 60%

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon

3D printing settings
I recommend printing these models with at least 3 walls to ensure durability! Please take your time taking the prints off the build, if too much force is applied too quickly the feet could risk snapping! If using a flex sheet always flex outward, peeling the print off slowly and gently is always best!

To make the feet stick, you must pull them down and while pulling them down giving them a gentle twist will make them stick on place and keep the pupper on his feet.

Pug Footling

pug_footling.stl

Have you ever wanted a pet raven? One to sit on your shoulder? This is your chance! If you print a bunch of them you can even have an unkindness (which is what you call a group of ravens) Yaay!! who doesn't want an unkindness?

You will receive two versions of the friendly raven fidget, one of which can even hold your shiny things like rings!

The feet can pop in and out, the raven is also able to stand on its feet by giving the feet a pull and a gentle twist!

Tested down to 60% and no supports required!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

3D printing settings
I recommend printing these models with at least 3 walls to ensure durability! Please take your time taking the prints off the build, if too much force is applied too quickly the feet could risk snapping! If using a flex sheet always flex outward, peeling the print off slowly and gently is always best!

Tested down to 60% with great results! No supports are needed for either model! The beak is set at a higher angle good cooling is required for a smooth print, you can face the model with the beak towards the cooling fans to help with the incline.

Raven Footling

Raven_Footling.stl

Did you know that Axolotls go through a stage where they only have two front feet? I didn't either, so I designed one and now you can print your own Axolotl baby tadpole!

This little guy is curious and is so fun to handle! He makes a great keychain as well!

This bundle contains two files, you will get the tadpole flexi as well as the keychain!

Tested down to 60% and up to 120%

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

Axolotl Tadpole Flexi

Axolotl_Tadpole_Flexi.stl

axolotl-tadpole-flexi-keychain.stl

A wild chonky seal appeared! Will you catch it?

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

Seal Flexi

seal_flexi.stl

Hi I'm a turtle!

I want to be your friend! My legs and head they wiggle, and I can stand, sit, and sploot on my way to win your heart!

I print easy, no fuss, and after I'm done printing I'll fit perfectly into the palm of your hand!

So pick me, and together we shall be!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

Turtle Flexi

Turtle_Flexi_V3.stl

Its a smol ladybug! Keep her in your pocket, or hide her in your house! She can be a plant buddy, or she can help you study!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

Ladybug Flexi

ladybug_Flexi.stl

Ladybug_Flexi_3MF.3mf

A simple geometric heart shelf!

In this package youll get:

Heart shelf for hanger
Heart shelf with blank back
3 kinds of hangers, one for small nails, one for a big nail, and a blank one for tape.

Tested down to 70%

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

The heart prints without supports, and does not require much infill 5-8% on most infill types.

The hooks can print standing up or laying down, printing them standing up will increase their strength I recommend using a brim to ensure adhesion, but if you are having issues printing them this way you can route them to have them print flat on the print build, this will result in a weaker hook.

Heart Shelf

heartshelf_Heart.stl

A new species of the layersingeenerus crab has been discovered on the cults3d islands! This one seems to have to ability to grow crystals on his back!

Test printed from 120% to 60%

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon https://www.patreon.com/Layersingreen

Crystal Gem Crab

CrystalGemCrab.stl

A magical mashup between a mermaid and a bunny! Super poseable, print in place and without supports! What can be better?

Comes in two files, one with antlers and one without!

2023 is the year of the rabbit, make sure to print this adorable bunny to bring you the best luck in the new year!

This model is for PERSONAL USE ONLY! commercial license available on my patreon https://www.patreon.com/Layersingreen

**3D printing settings**
No supports! I recommend to print with minimum 3 walls, and ensure that you have proper bed adhesion. Tested to scale down to 60% and up to 120%

Merbunny

MerJackalope.stl

A snake planter to keep your plants happy. Comes with two versions; One with a hole and one without.

Can be scaled! Prints without Supports!

This model is for PERSONAL USE ONLY! commercial license available on my patreon https://www.patreon.com/Layersingreen

3D printing settings
The bottom of the planter can be made thicker or thinner by sinking the model into the print bed in the slicer. Please make sure you have at least 4 bottom layers!

Nozzle: 0.4
Layer Height: 0.2
Infill: ZigZag 10%
Supports: No

Snake Pot

snakepotremake.stl

**This release includes:**

🐉 RubiKuro dragon
🐉 2 Prepainted RubiKuro 3MF files
🐉 Rubi Egg

RubiKuro was tested down to as little as 50%, however I dont recommend going below 60% scale. Prints without supports. The large gradient Rubi in the pictures is approx 135% scale. I recommend using minimum 3 walls, and if you sometimes have adhesion issues I recommend using a brim with a brim gap between 0.3-0.6 mm, especially when printing in multicolor.

**Egg**
I have heard and took into consideration the concerns that were brought to my attention with Kaida's egg. I have made a few changes to this egg design, the egg is wider at the base which allows a dragon to fit much more comfortably! I have also made the tabs on the top a bit shorter to allow for easier opening and closing. Having a looser fitting top introduces a chance of the top coming off when shaking the egg upside down hard enough, it should however stay closed when flipped upside down, and with regular use. The Egg and Rubi are 1:1 scale, this means that 100% Rubi will fit into 100% egg. Egg prints without supports.

If you are using Bambu slicer I recommend using Arachne for your wall generator, this will ensure that there is an even number of walls on the egg.

When placing Rubi into the egg: It doesn't particularly matter which end you place in first, as long as you coil her up, then place the top over in line with the tabs and give a gentle shake, the top should snap in place easily. You can also place Rubi into the top of the egg, and bring the top down into the bottom. I have made a short clip of how to place Rubi into her egg, linked below

**Filaments used:**
Blue and Pink Rubi: Polymaker PLA Ice, Ziro Matte Pink, Polylite PLA Pro Metallic Magenta, Ziro PLA pro Snow white

Black, blue, red Rubi:  Ziro Gradient Twinkling PLA, Cookiecad Pale Blue Elixir PLA, Cookiecad Ruby Red Elixir PLA, Cookiecad Sloar Flare PLA.

Grey and pink Rubi: Polyterra PLA Fossil Grey, Cookiecad Pixie Dust PLA, Hatchbox sparkling grey.

Yellow pink gradient Rubi: Ziro Matte gradient sunlit Petal, Polylite PLA Starlight Mercury.

Large gradient Rubi: Eryone Matte Marcron Rainbow

I think that's all! If you have any questions please let me know!! 
----------------------

Rubikuro and Egg

Rubikuro.stl

Its a woody dice stand! It comes with a space to put a full set of dice, and the middle stump opens up for more space!!

The snail functions as a lid, but can also be sunk into the bed in the slicer to cut off the platform and then it becomes just a snail friend!

This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon

https://www.patreon.com/Layersingreen

🐌🐌🐌

Woody Dice Stand

WoodyDiceStand_Stand.stl

Rubikuro_3mf_3color.3mf

Rubikuro_3mf.3mf

Rubi_Egg_Bottom.stl

Rubi_Egg_Top.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Layersingreen

Achievements

Sapling

Pinned models

Rubikuro and Egg

Raccoon and Dumpster

Bloxlotl Flexi

Happy Dumpster

Raccoon Flexi

GingerBread Tushie

Arcadia Dice Tower

Fox Flexi

Forest Pixies

Deer Pixie

Moth Pixie

Mushroom Pixie

Skelly Crab

Bat Bobblehead

Water Element Dragon: Mizu

Octo Spinner

Butt Frog Pack

Wood Stump Dice Tower

Kosha

Butt Goblin Pack

Pug Footling

Raven Footling

Axolotl Tadpole Flexi

Seal Flexi

Turtle Flexi

Ladybug Flexi

Heart Shelf

Crystal Gem Crab

Merbunny

Snake Pot

Rubikuro and Egg

Woody Dice Stand