Introducing the PEA SHOOTER SLINGSHOT!

This is a throwback to an awesome toy I used to have as a Kid that would make me spend countless afternoons playing with in the garden.
Back in the day, the original design was just a piece of wood in a Y shape attached to a rubber band in order to "shoot" little stones you found along the way in order to test your aim.

Since I have been messing around with 3d printed spirals lately, I came up with this amazing design that actually works like a charm.

This pea shooter actually works perfectly and It can shoot quite far for a 3d print.

The also very cool thing is that the spiral and handle is print in place so you will not have to worry of parts snapping. If you print it with a good infill it should holt its own.

This print consists of 3 different parts:
- Spiral and handle
- Pea accommodation site
- Pea
The design has been created so that the part fits perfectly and does not come off when shooting so you would not have to worry abut that either!

I hope you like it and if you do be sure to drop a like and a follow.✨

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!
**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**IMPORTANT:** This piece is not design to be shot at people since it could be harming for the eyes. This is something to test your aim against something like a target of others. BE SAFE OUT THERE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**Recommended printing settings:**
For the settings I would not change the ones that come as standard. 
You can also fiddle around and add a bit more infill % if you really want to make it indestructible but it should not need it.

You could also scale it up but REMEMBER TO SCALE ALL THE PARTS THE SAME! While scaling I have seen that the perfect fitment of the Pea accommodation can vary due to the change of layers so be aware of this!

PRINT IN PLACE SLINGSHOT (Pea shooter)

1.-Slingshot_Pea_shooter_complete.3mf

THIS IS THE LAST PART OF THE HALLOWEEN DECORATION SERIES FOR 2024!
As Halloween is in a few days, I thought it would be a great idea to offer the opportunity to buy all my Halloween models in a bundle pack so... here it is!

This bundle will include the following models:

-Halloween jack o' Lantern
-Skeleton hand decoration
-Halloween skull bone mask
-Rest in print Halloween coasters

Personally this is a great opportunity if you liked any of my previous models and you were not sure if to buy it or not. Well, I hope that with the extra models you will receive you make up your mind and end up getting it!

All models are carefully designed and printed in order to meet quality criteria (as always with all of my models) so just hit print and you will have them soon enough!

If you want to see the designs in action Click the link ▶️: https://www.instagram.com/printplay.3d/?hl=en

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

                                               **3D printing settings for all models:**
**MODEL: JACK O' LANTERN**

MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES WITH THE MAGNETS!

Layer height:
-0.2 mm is perfect

-SUPPORTS ARE NEEDED FOR ALL OF THE MODELS. I used the basic Bambulab tree supports and has all turned out to be perfect.

-No extra adhesion to the bed is needed

-Infill: 10% in order to end up with a rigid piece. Less could break the piece when adding the magnets.

POST PRINT:

The magnets do not need to be glued in, just press them with the pointy end of the pliers that came with your printer!

**MODEL: SKELETON HAND DECORATION**

-MODEL SCALABLE! Current Scale works very good to hold the Jack-o-Lantern so keep that in mind!

Layer height:
-0.2 mm is perfect

-SUPPORTS ARE NOT NEEDED FOR ANY OF THE MODELS

-No extra adhesion to the bed is needed

-Infill: 10% in order to end up with a rigid piece

**MODEL: SKULL BONE HALLOWEEN MASK**
All the files are scaled for a "standard adult head" but in case you need to scale there is still space on the buildplate to make it a big bigger.

Layer height:
-0.2 mm is perfect. You could go for lower layers for extreme detail or use the Adaptative layers from bambulab to have best of both worlds

-SUPPORTS ARE NEEDED. They are already ready for all files but you can check and optimize as I used the Standard Tree support (that, in my opinion, work amazingly good)

-Adhesion is needed to print the teeth but, as the support, is already coded in the STLs

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

**MODEL: REST IN PRINT COASTERS**
Layer height:

-0.2 mm is perfect for this print.

-SUPPORTS ARE NOT NEEDED.

-Adhesion is also not needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

In case of stringing due to a lot of filament change you can use a blowtorch post print to eliminate the residue of plastic and enhance the final look!


Halloween Bundle Printplay3d (4 models)

2.-Horns_Long_Version.3mf

WELCOME TO HALLOWEEN DECORATION PART 4!

🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃🎃

Today I bring another Coaster upgrade, the REST IN PRINT COASTER COLLECTION!

This print will ensure a great look for the coasters that you can use during your Halloween events happening soon!

The print contains 8 different designs that will give the extra touch. My personal favorites are the pumpkin ones, they are amazing😍

In terms of printing this is a super simple print that will need assembly. You just have to glue the tomb to the storage container.

This was printed using the following polymaker filaments:

-Lava red
-Sunrise Orange
-Charcoal Black
-Cotton White
-Fossil Grey

As always, amazing results with this filament. You can't go wrong when using them! If you have not tried them you have to, you will not be disappointed!🫶🏽

I hope you like it and if you do be sure to drop a like and a follow. More models coming out later on this week!✨
Do not hesitate to drop a follow because A LOT MORE MODELS ARE COMING SOON!!

If you want to see this design in action Click the link ▶️:

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**RECOMMENDED SETTINGS**

Layer height:

-0.2 mm is perfect for this print.

-SUPPORTS ARE NOT NEEDED. 

-Adhesion is also not needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

In case of stringing due to a lot of filament change you can use a blowtorch post print to eliminate the residue of plastic and enhance the final look!


REST IN PRINT HALLOWEEN COASTER COLLECTION

Coasters_1_2_3_6_7_painted.3mf

WELCOME TO HALLOWEEN DECORATION PART 3!

Since Halloween is SUPER near I have prepared a series of models in order to have an amazing PINTING OCTOBER!

To start continue with the series I have the honor to present the SCARY SKULL BONE MASK!

I have prepared this amazing high detailed mask to enhance the looks on your Halloween parties or when going door to door for the trick or treat!

The fitment is on top but still scalable in order to make it bigger or smaller! Also the mask is designed to be able to have small foam parts on the inside in order to adjust it to your face if you do not want to have it super close to the face when wearing it for a long time! It also has some holes on both sides in order to add a cord or some Velcro to fix it super easy to the head.

My personal recommendation is to wear it with a dark "Balaclava" underneath that covers your face in order to have the best look possible.

I used polymaker_3d filaments as always for that amazing final result! I used the Glow in the dark green for the bone part, Charcoal Black for the black parts and Gold for the Tusks to give a bit of detail.

With the model you will also have available as a SURPRISE:

-Longer horns that are my absolutely favorite
-Broken horns. In order to add a broken horn for the side that you prefer if you want to opt for that look.
-Broken Tusks in order to go with the broken horn look if you want

Do not hesitate to drop a follow because A LOT MORE MODELS ARE COMING SOON!!

If you want to see this design in action Click the link ▶️:

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!
**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

Let's see how this amazing mask does for the contest with ELEGOO :) #ThangsLovesELEGOO

**3D printing settings**
All the files are scaled for a "standard adult head" but in case you need to scale there is still space on the buildplate to make it a big bigger.

Layer height:
-0.2 mm is perfect. You could go for lower layers for extreme detail or use the Adaptative layers from bambulab to have best of both worlds

-SUPPORTS ARE NEEDED. They are already ready for all files but you can check and optimize as I used the Standard Tree support (that, in my opinion, work amazingly good)

-Adhesion is needed to print the teeth but, as the support, is already coded in the STLs

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

SCARY SKULL BONE MASK

1.-Bone_Mask_V2.3mf

**WELCOME TO HALLOWEEN DECORATION PART 2!**

This time, this second part of the mini-series is about a skeleton/mummy hand that can be used as a holder for the previous print or for various items like controllers or even your phone!

I have prepared both hands (left and right) for this one in order to bring your decorations up! Works SUPER good to grab the previous design (Jack-o-lantern) and others.

This print is perfect to give a little touch to other parts of the house in order to be Halloween ready.

For this print there are no other materials needed but let me know if you want me to add some holes for magnets somewhere (full custom ;) ) if you need it!

I used polymaker_3d filaments as always for that amazing final result! I used Cotton white and Glow in the Dark green, my new favorite filament to use!

Do not hesitate to drop a follow because A LOT MORE MODELS ARE COMING SOON!!
Drop a like💜 really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

**Recommended settings:**

-MODEL SCALABLE! Current Scale works very good to hold the Jack-o-Lantern so keep that in mind!

Layer height:
-0.2 mm is perfect

-SUPPORTS ARE NOT NEEDED FOR ANY OF THE MODELS

-No extra adhesion to the bed is needed

-Infill: 10% in order to end up with a rigid piece
-Infill: between 5 - 10% is more than enough. I printed mine with 5%

SKELETON HAND DECORATION

Hand_1.stl

Magnetic flowers for kids designed as an activity. The idea is for the kid to match the color of the plate with the correct flower.

This activity is created for the kid to understand and match the colors of the flower with the undertray without any explanation. This is very important because the kid can explore the activity and how the magnets work.

Although it seems very easy, the shape of the pot (round bottom which makes it kind of "unstable") makes it a challenge for them so they will have to control in a very precise way the movements they do when joining the 2 parts together. This is done totally on purpose so do not be surprised if it takes a minute for them, it is not that easy!

This prints uses 10 x 4 mm Magnets that you can buy off Temu or Amazon in order to join the different parts of the print. Post process will require to glue the magnets to the print in order to ensure that they stay in place.

The idea of the magnets is for it to be easier to join the 2 different parts as well as adding the flowers to any other metallic surface if needed (as decor for Spring decoration for example).

THIS ACTIVTY NEEDS TO BE SUPERVISED FOR SAFETY!

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C5qvxAcNXr2/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

**Buying this model does not grant access to sell it commercially, just for PERSONAL USE!**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

Recommended printing settings:
-No supports are needed for any of the parts
-Models are not scalable since they use 10 x 4 mm magnets and the fitment is perfect.
-No extra adhesion is needed
-0.2 layer height is more than enough to have a great quality
-recommended 15% infill to make the pierce more resistant to potential damage


MAGNETIC FLOWERS FOR KIDS

3.-Flower_magnet_piece.3mf

1.-Flower_V2_10x4mm_Magnet.3mf

WELCOME TO HALLOWEEN DECORATION PART 1!

Since Halloween is suuper near I have prepared a series of models in order to have an amazing PINTING OCTOBER! 

To start this mini-series I present you my take on the super Famous Jack o'Lantern 

I have prepared 4 different models of faces for this one in order to have a bit or variety when decorating so it does not look repetitive. My personal fav is the one that has the eyes with different sizes by a lot, it simply looks amazing!

This print will use the little electric candles in order to create the light effect! As said, the set up is super easy and it is safe to use everywhere. I got mines from Temu but I am sure you can get them also in Amazon for super cheap!

You will also need 4 magnets 5x3mm per pumpkin in order to close them. This brings new opportunities because you can attach half of the pumpkin (with the candle inside) to ANYTHING MAGNETIC! Just let your creativity flowing, can't wait to see with people come up with!

MATERIAL LIST:
-Electric candle from Temu/Amazon
-4 5x3mm magnets per pumpkin

I used polymaker_3d filaments as always for that amazing final result! Sunrise orange and Army Dark Green just look amazing together don't you think?

Make sure to comment if you would like the same model but to use with real candles! I think it can be also a great addition for your home decor!

Do not hesitate to drop a follow because A LOT MORE MODELS ARE COMING SOON!!

Drop a like💜 really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

++Recommended Settings**

MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES WITH THE MAGNETS!

Layer height:
-0.2 mm is perfect

-SUPPORTS ARE NEEDED FOR ALL OF THE MODELS. I used the basic Bambulab tree supports and has all turned out to be perfect.

-No extra adhesion to the bed is needed

-Infill: 10% in order to end up with a rigid piece. Less could break the piece when adding the magnets.

POST PRINT:

The magnets do not need to be glued in, just press them with the pointy end of the pliers that came with your printer!

MAGNETIC JACK O' LANTERN

4.-Hollow_Pumpkin_Style_4_Fake_Candle(Magnet).3mf

Magnetic bees for kids designed as an activity. The idea is for the kid to match the color of the hive with the correct bee. They will love to play around with them, That I can ensure!

This activity is created for the kid to understand and match the colors without any explanation in a sense of exploring by themselves.

The idea of the magnets is for it to practice the pinching force that is needed to hold a pen/pencil when learning to write! There is a pincher added in the model but I have found that using a metallic one is way better for the little ones!

For this model you will need to use 20 magnets 10 x 4 mm (or smaller) that you can get from Amazon/Temu.

THIS ACTIVTY NEEDS TO BE SUPERVISED FOR SAFETY REASONS!

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C-GAmn5N34f/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

**Buying this model does not grant access to sell it commercially, just for PERSONAL USE!**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**Recommended settings for printing:**

NO SUPPORTS NEEDED FOR ANY PART!

MODEL IS  NOT SCALABLE since it is ready to add magnets (10 x 4 mm) at the bottom of the bees and petals. In total you will need 20 magnets!

Adhesion: Nothing is needed.

Layer height: 0,2 mm is more than enough

Infill: 5 - 10 %. Consider more if younger kids will play with it as the item can receive some damage. 

Post -Process: Bees, flowers and the hive come in parts and will need further assembly. This is super easy and straight forward to do with a bit of fast glue. You may also need to trim some little pieces to make everything fit but it is a super easy process to do!

MAGNETIC BEES FOR KIDS

3.-Hive_Complete_V2_(2cm_heith).stl

Come on let's be real. How many Benchys you have around? Yeah I figured. I am sure that they are just lying around...

Well this bundle of 3 different Benchy decoration that is about to change! Now you will be able to give the Benchys printed a better decorative look (specially your fist one in a new printer for example). This is an amazing print that will give a great touch on your 3d printable collection!

**In the files you will find:**
-The: Little wave decoration
-The Tsunami! decoration
-The: Oh S**t! KRAKEN! decoration
- EXTRA for THANGS DOWNLOADS: The tentacle on moving seas decoration. (this model is not featured as a picture and it is only to be found by the people that download the bundle. Little gift for you guys ;)

If you want to see this design in action Click the link ▶️:
https://www.instagram.com/p/C_s-E8yNsax/?hl=en

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**Recommended settings:**

MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES!

Layer height:
-0.2 mm is perfect

-NO SUPPORTS ARE NEEDED FOR ANY OF THE MODELS

-No extra adhesion to the bed is needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

Benchy Boat Decoration Bundle

Benchy_Decoration_Style_3(Octopus).3mf

Are we dreaming?

Well.. now you have a way to check it with this awesome look alike inception totem. Similar style to the one used in the film!!

This one is designed to be a little Fidget to have on the desktop and make it spin endless times. It has an incorporated magnet (one at the base and another one at the totem) so it stays on the same spot while spinning. No one will know about the magnets, trust me ;)

It also works on any other surfaces if you do not want to use the base provided.

IMPORTANT: If you are not using a Bambulab Printer use the files with NO_PAUSES name. It seems that Cura slicer does not open the files with the pause setting.

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

**Recommended settings:**

-For this print it is recommended the use of magnets for weight and stability for the rotation of the totem. This print uses two 10x3 mm magnets for the base and the totem. The STLs have the pauses incorporated so you can add the magnet mid print and let the print continue to hide them!

-NO SUPPORTS NEEDED FOR ANY PART!

-MODEL IS SCALABLE but keep in mind the gaps for the magnets!!

-Adhesion: Nothing is needed.

-Layer height: 0,2 mm is more than enough

-Infill: 10 % is more than enough

INCEPTION MAGNETIC ROTOR

1.-Rotor_handle_no_pauses.stl

HEY HEY HEY LEAVE MY SWITCH IN PLACE!
This UFO (that is trying to steal my switch) is an amazing decoration made to enhance your gaming setup! This is an amazing way to prepare for Halloween and to keep after. The end product is amazing and I could not be happier for it!

The fitment is on point as well as the equilibrium with the machine installed. I designed it so the Switch is angled towards the left when looking it from the front. I can make it so that the UFO can go to the left if you have your switch at a place that needs it, just drop me a message on Instagram!

The print is divided in 3 parts. The UFO, the joiner and the Base. You will see that the Joiner can move in between the two parts in order to give enough space for the glue to not overflow when putting the 3 pieces together. Don't go crazy thinking your fitment is of!. It is super easy to print and even easier to assemble.

If you want to see this design in action Click the link ▶️: 
https://www.instagram.com/p/C_OF1D7NZW-/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!
**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**3D printing settings**
MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES!

Layer height:
-0.2 mm is perfect

-NO SUPPORTS ARE NEEDED

-No extra adhesion to the bed is needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

UFO SWITCH DOCK DECORATION

UFO.stl

Amazing High quality model of a V8 engine.

The engine shows only 2 of the 8 pistons in a V8 in order to see from the frontal part how the movement of the pistons are in a real engine.

The crankshaft moves with a lever attached to it at the back making the pistons go up and down.

Model has tight fit on all of the parts for a perfect finish, specially between the pistons and the block.

This can be used as a decoration item or to explain how an engine works!

(Model comes with a Wrench to tight all of the nuts)
(Use the pictures provided as instructions and contact me if more info is needed via DM without any issue!!)

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

3D printing settings
MODEL IS SCALABLE. It just depends on how big you want the final product to be. I printed mine at 50% and ended up being amazing.

Layer height: 0.2 mm or less for a higher quality

Supports: Some of the parts need supports because of the arches in STL 3.2 or overhangs in STL 3.1. Check your settings on supports and tweak it if needed.

Adhesion: No need of extra adhesion for any of the STLs.

Infill: 10% is more than enough.

PISTON ENGINE MODEL

3.1-Engine_Block_Printed_only_engine(1).stl


**ARTICULATED BUTTERFLY**

Here you will find 2 different STLs. One for the big butterfly (the wings are bigger) and a different one for the smaller version (wings are scaled down for a more cute look ;) ).

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**3D printing settings**
MODEL IS SCALABLE but check the slicing before printing to ensure the scale is enough to not fuse the articulations together (can end up happening if you scale down too much).

Layer height: here you have different options, all of them could be used:
-0.2 mm for a "not so detailed" final print. Use this only as final resource.
- 0.08 mm for a super detailed final print. This is the one I usually chose.
-You could also use the adaptative layer height on BambuStudio to combine the best of both worlds

NO SUPPORTS NEEDED!

Adhesion: I used a brim to prevent Warping but you should be safe without it.

Infill: 10% is more than enough.

ARTICULATED BUTTERFLY

Butterfly_Smaller_Wings.stl

Take aim, throw, and score!

Presenting the new portable mesh Dartboard! This is the needed piece in your desktop. Makes quite the decor touch as well as a good challenge. Perfect for a bit of entertaining during the long Home office hours. Who is up for it, will you be able to get the center?

What does the model include:

-This model comes with 2 options of Dartboard. A more minimalistic/clean one (with only the center painted as red) and another one more towards a more "realism" look.

-This model also includes the support that tilts the Dartboard that has storage for 2 darts.

-In the STL files you will also find the Dart. This has a special designed tip that is resistant to impacts (tested) since it is full plastic. The Dart has a "Rocket" style and can be placed Vertically also as decoration.

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

Buying this model DOES NOT grant access to sell it commercially, just for PERSONAL US.

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**3D printing settings**
Recommended settings:

-NO SUPPORTS NEEDED FOR ANY PART!

-MODEL IS SCALABLE

-Adhesion: Nothing is needed.

-Layer height: 0,2 mm is more than enough

-Infill: 10 %

IMPORTANT: To be printed at slower speeds than normal since the grid needs a lot of precision to be formed correctly. If you print at normal speeds the grid will not be a grid and the dart will not stay in.

PORTABLE DARTBOARD WITH DARTS

1.0.-Dartboard.stl

**DESERT ARTICULATED RATTLESNAKE (1.2 METERS)**

Check the mobility out HERE: https://www.instagram.com/p/C9xS7PKtwV7/?hl=en

Drop a follow if you want more content like this one ;)

This is a **SUUUPER** long and cute desert rattlesnake. As you can see, it can get up to 1.2 m (depending on your slice scale) on a 256x256 mm plate!

The model is amazing and super simple to print. It will be a little challenge for your clearance settings, see if you can print it (it is easy in the end don't worry ;) ).

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**3D printing settings**
MODEL IS SCALABLE but check the slicing before printing to ensure the scale is enough to not fuse the articulations together (can end up happening if you scale down too much)!!

SPEED: I printed this at 50% speed on my printer to ensure the final result was amazing and it worked perfectly. Personally, I would not go too fast due to the high quantity of jumps the printer will have to perform. If you have small extrusion problems it will be visible so keep the speed down for this one!

Layer height: here you have different options, all of them could be used:
-0.2 mm for a "not so detailed" final print. Use this only as final resource.
- 0.08 mm for a super detailed final print. This is the one I usually chose.
-You could also use the adaptative layer height on BambuStudio to combine the best of both worlds

NO SUPPORTS ARE NEEDED!

Adhesion: I used a brim to prevent Warping but you should be safe without it.

Infill: between 5 - 10% is more than enough.

DESERT ARTICULATED RATTLESNAKE (1.2 METERS)

Desert_Snake_Articulated_Simplified_V2.3mf

An amazing print that will help you organize if you have more build plates than printers (like my case). It will case up to 6 build plates (256x256 mm). A must have if you possess ANY of the Bambulab printers!

This print can act as:

A Tripod: Specially useful if you have an A1 printer and space to flex on your build plates

A Side mount: If you have a P1S or any of the X1 series AND an AMS system. The AMS is necessary to side mount it since the weight of it will fix the plateholder (as counterweight).

This build does not use ANY GLUE (i did not use even one drop on mine) but could be a good addition if needed. Layer lines and how it is assembled will ensure that the final product does not snap!

USE THE PICTURES AS INSTRUCTIONS (it is super clear and easy) you can't miss it!

Any question regarding the model or how to assemble it can be sent to my Instagram DM: https://www.instagram.com/printplay.3d/

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**3D printing settings**
-You will find STLs for all the pieces separately and the 5 together in case you want to to multicolor in a single color printer ;)

-MODEL IS NOT SCALABLE: Everything has been measured to a perfect fit!

-Layer height: here you have different options, all of them could be used:
   -0.2 mm for a "not so detailed" final print. Use this only as final resource.
   - 0.08 mm for a super detailed final print. This is the one I usually chose.
   -You could also use the adaptative layer height on BambuStudio to combine the best of both worlds

Supports ARE needed for one piece only. Normal and Automatic Bambulab supports works wonders then removing (when pliers are used) highly recommended

Adhesion: Nothing please, the use of brims will mess the perfect fit!

Infill: 15% is necessary on this one to ensure strength.

BUILD PLATE ORGANIZER FOR BAMBULAB

Bambulabs_SideMount_and_Tripod_Plateholder_5_Parts.3mf

Well the time to upgrade the coasters at your house but don't worry, I got you ;)

This amazing articulated coaster resembling tentacles from an octopus🐙. It will grab your mug so it does not go anywhere! ☕

Perfect to decorate part of your house or the part of your desktop designated to your mug while working/ designing

It is super easy to print. The Design comes in 2 different STLs (tentacles and the mug pad) in case you need to print in a different scale.

Drop a like💜, comment 💬 it really helps us creators to get more done :D

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C98AWSaN-JK/?hl=en

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**3D printing settings**
MODEL IS SCALABLE for different mugs

Layer height:
-0.2 mm is perfect

-NO SUPPORTS 

No adhesion is needed

Infill: between 5 - 10% is more than enough.

ARTICULATED SELF ADJUSTING TENTACLE COASTER

Tentacle_Coaster_Tentacles.3mf

I wanted to do something that was both articulated and very flexible **AND magnetic**. Like this, the articulation could make it so the dragon would stick to **EVERYTHING, FLAT OR CURVED!**

This amazingly detailed dragon will do just that. It is **SUPER** flexible as you can see and will snap into anything metallic, **EVEN CURVED SURFACES** (following the curve line of the dragon). The details of the scales are truly amazing.

The dragon has a socket **for 51 5x3 mm magnets** in each body part. You can find pack of those in **Aliexpress or Temu (I used this ones)** with amazing prices over high quantities. You can get a lot of those because I will use this ones in the future for other articulated magnetic builds, you will love them ;).

Use a color changing filament for the finish I had. The print is **SUPER** easy and will print without any problems!

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Do not hesitate to follow me on Instagram to be aware of the next upcoming Articulated Magnetic crafts! --> https://www.instagram.com/printplay.3d/

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

Any question regarding the model can be sent to my Instagram DMs: https://www.instagram.com/printplay.3d/

Articulated_Magnet_Dragon_V1.3mf

**LOW POLLY PANTHER INCENSE HOLDER**

I have been using incense sticks a lot lately but my holder was plain and boring... Too typical you know?

Well, presenting the Low Poly Panther incense holder to fix this 🐈‍⬛!
The model started as a customer request that wanted a low poly panther as decoration for the living room (full black style. While I was designing it i fell in love with the end product so decided to make some tweaks to make it be an incense holder.

Prints SUPER easy even when using supports (Bambulab supports are just🤤). The final product needs assembly but it is super easy and SUPER fast (you have a couple of gifs showing how). The idea is to NOT glue the two parts of the tail together so they will hold the incense stick, works perfectly!

The finish is simply amazing and I couldn't be happier with it, it was a great call to convert the decorative with the useful touch.

The filament I used on the different panthers:
-Polymaker Army Dark green
-Polymaker Starlight Jupiter
-Esun PLA silk magic (green/blue)

Drop a like💜, comment 💬 it really helps us creators to get more done :D
Do not hesitate to follow me on Instagram to be aware of the next upcoming Articulated Magnetic crafts! --> https://www.instagram.com/printplay.3d/

Buying this model DOES NOT grant access to sell it commercially, just for PERSONAL US. 

Any question regarding the model can be sent to my Instagram DMs: https://www.instagram.com/printplay.3d/

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

**3D printing settings:**
-MODEL IS SCALABLE BUT SCALE BOTH PARTS THE SAME!

Layer height:
-0.2 mm is more than sufficient but you could go for less (0.08) to have an amazing finish on the curved surfaces

-SUPPORTS ARE NEEDED. I used the normal supports from Bambulab (Automatic ones) and it turned out to be perfect. The removal is super easy and does not affect the size for the joiners.

-No extra adhesion is needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

LOW POLLY PANTHER INCENSE HOLDER

1.-Body_and_Joiners.3mf

**OCTOPUS SWITCH DOCK**
It was time to upgrade my old Switch dock version. Nothing wrong with that but as the designs that I upload I like to be constantly moving with new things! This is why I ended up making this octopus Switch docker! **Perfect to decorate part of your gaming place!**

This octopus design 🐙 is amazing and SUPER realistic. The fitment is on point as well as the equilibrium with the machine installed. I designed it so the Switch can go inside both ways. This is because like this you can angle it both ways, better for decoration ;)

It is super easy to print but will take some time SO BE PATIENT, IT WILL BE WORTH IT.

The Design comes with 2 different STLs (2 for the price of one,) the grabbing one and the one that suspends the Nintendo in the air.

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C-GAmn5N34f/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

**Buying this model does not grant access to sell it commercially, just for PERSONAL USE!**

**YOU FILL FIND THIS MODEL ON MY COMMERCIAL LICENCE MEMBERSHIP. ONLY WHEN THIS MEMBERSHIP IS ACTIVE YOU WILL BE ABLE TO SELL THIS MODEL YOURSELF**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**3D printing settings**
MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES!

Layer height:
-0.2 mm is perfect

-SUPPORTS ARE NEEDED FOR BOTH STYLES

-No extra adhesion to the bed is needed

-Infill: between 5 - 10% is more than enough. I printed both with 5%

OCTOPUS SWITCH DOCK DECORATION

Octopus_Sculpted_Switch_Docker_V2_Painted.3mf

Unlock the possibility to sell PrintPlay3D Models!

**Features:**
Unlock PrintPlay3D models with COMMERCIAL LICENCE that you will be able to print and sell on your shop!
The models that you will find here will be marked on the description on each of them and will contain almost all of my models.

The ONLY CONDITION for all of this models will be that you will need to have the membership on in order to have the commercial license

**Benefits:**
You will be able to print and sell as much PrintPlay3d models that you can as well as use them for yourself!
You will have access to troubleshooting help if it is needed for all of the models to ensure the final quality is more than perfect via my email or DM on Instagram!

**Other information:**
- All my models are printed before upload to make sure the piece is as intended and it does not have any issues.
- I am available if doubts or problem arise for all of my models. Also I can consider modeling custom bits for the models if you desire so (like special logos on them as an example). Creativity at its best!


Commercial PrintPlay3D Models!

Unlock all of the Printplay3D models posted!

**Features:**
Discover a wide range of models suitable for beginners to advanced builders and printers. In this plan you will find multiple types of models, from switch dockers, articulated prints and many others!
Members will have 3 downloads per month on all the models I post, choose wisely!

**Benefits:**
Enjoy new models ensuring your creative pursuits stay fresh and exciting. 
Subscribe today and start building your creativity!

**Other information:**
- All my models are printed before upload to make sure the piece is as intended!
- Feel free to drop me a message on Instagram if something is needed (Instructions, custom parts, custom modifications etc..)
- **IMPORTANT: ALL of the models are for private use only**

Printplay Models!

1.-Wings_eyes_joiner_Bees_(10_units.3mf

2.-Body_Bee_with_color.3mf

3.-Centrer_flower.stl

4.-Joiner_flower.stl

5.-Petal_flower.stl

Hive_bot_Part1.stl

Pincher.stl

1.-Hollow_Pumpkin_Style_1_Fake_Candle(Magnet).3mf

2.-Hollow_Pumpkin_Style_2_Fake_Candle(Magnet).3mf

3.-Hollow_Pumpkin_Style_3_Fake_Candle(Magnet).3mf

5.-Hollow_Pumpkin_Style_4_Fake_Candle(Magnet).3mf

2.-Horns_Broken_Version.3mf

2.-Horns_short_Version.3mf

3.-Normal_teeth_and_broken_tusks.3mf

Hello! I am Printplay3D. I design and Print things, hope you like my models :)
Find me here: https://www.instagram.com/printplay.3d
Email: printplayd@gmail.com

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Printplay3d

Achievements

Seedling

Pinned models

MAGNETIC BEES FOR KIDS

MAGNETIC JACK O' LANTERN

SCARY SKULL BONE MASK

PRINT IN PLACE SLINGSHOT (Pea shooter)

PRINT IN PLACE SLINGSHOT (Pea shooter)

Halloween Bundle Printplay3d (4 models)

REST IN PRINT HALLOWEEN COASTER COLLECTION

SCARY SKULL BONE MASK

SKELETON HAND DECORATION

MAGNETIC FLOWERS FOR KIDS

MAGNETIC JACK O' LANTERN

MAGNETIC BEES FOR KIDS

Benchy Boat Decoration Bundle

INCEPTION MAGNETIC ROTOR

UFO SWITCH DOCK DECORATION

PISTON ENGINE MODEL

ARTICULATED BUTTERFLY

PORTABLE DARTBOARD WITH DARTS

DESERT ARTICULATED RATTLESNAKE (1.2 METERS)

BUILD PLATE ORGANIZER FOR BAMBULAB

ARTICULATED SELF ADJUSTING TENTACLE COASTER

Articulated_Magnet_Dragon_V1.3mf

LOW POLLY PANTHER INCENSE HOLDER

OCTOPUS SWITCH DOCK DECORATION