NON-COMMERCIAL - V2 FRAME ONLY

Video - https://www.instagram.com/reel/C9SlWjeOBwJ/?utm_source=ig_web_copy_link

 This complex color/low waste model uses 8 different colors (13 instances). AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 3 different 3MF files for Bambu Studio. Please read all the instructions carefully. 

For 1 AMS - I have added 13 filaments to the slicer (some duplicates, one for each swap) and set the slicer to print all 13 in order. This way you can assign them when printing based on the chart below and keep the profiles for each filament type. It will be a bunch of swaps either way, but this should keep it straight forward. So basically just treat it as if there are 13 different colors in order. 

For 2 AMS units - just load and print. This is the ideal setup for this model. 

For  NO AMS - pauses already set (manual color changes). 

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. With 1 AMS when it gets to slot 4 in the print it will error and force a pause. You can then load the new colors (5-7) in AMS slots 1-3 then put color 4 back in and repeat this process by unloading color 4 when it is complete it will pause when it is time for color 8. In this case repeat again for color 12. This will probably be pretty handy for this model as there is a bunch of swaps in the 1 AMS profile and this will ensure you don't miss them. 

If you do not have Bambu Studio/Orca I recommend using it to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick.  

If you have any questions about printing this hit me up. 

AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.

MODEL COLOR -- [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13]

1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2] [3] [4] [1]  [2]   [3]   [4]   [1] 

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] 

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8]  

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.48mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. As with all Hueforges if you scale the model DO NOT change the Z dimension. If you substitute filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

NOTE: The Savannah yellow is only used in the text so you should be able to swap this without affecting the rest of the painting. 

Filaments Used:
PLA BambuLab Matte Charcoal Transmission Distance: 0.6
PLA BambuLab TD-1 Blue Gray Transmission Distance: 3.1
PLA BambuLab TD-1 Jade White Transmission Distance: 6
PLA BambuLab TD-1 Red Transmission Distance: 4.3
PLA BambuLab TD-1 Cyan Transmission Distance: 2.3
PLA Polyterra TD-1 Savannah Yellow Transmission Distance: 3.6
PLA BambuLab Matte TD-1 Dark Red Transmission Distance: 0.1
PLA BambuLab TD-1 Yellow Transmission Distance: 5.3
This print uses 8 unique filaments

Swap Instructions:
Start with Charcoal
At layer #8 (0.72mm) swap to TD-1 Blue Gray
At layer #11 (0.96mm) swap to TD-1 Jade White
At layer #14 (1.2mm) swap to TD-1 Red
At layer #18 (1.52mm) swap to TD-1 Cyan
At layer #21 (1.76mm) swap to TD-1 Savannah Yellow
At layer #26 (2.16mm) swap to Charcoal
At layer #28 (2.32mm) swap to TD-1 Red
At layer #36 (2.96mm) swap to TD-1 Dark Red
At layer #37 (3.04mm) swap to TD-1 Yellow
At layer #41 (3.36mm) swap to TD-1 Jade White
At layer #45 (3.68mm) swap to TD-1 Cyan
At layer #47 (3.84mm) swap to TD-1 Jade White for the rest.
 

Airbender Graffiti - Filament Painting 

Airbender Graffiti - 208x208.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

 This complex color/low waste model uses 9 different colors (11 instances). AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 2 different 3MF files for Bambu Studio. One for people with AMS unit(s), and one for people with NO AMS with pauses already set (manual color changes). I used 2 AMS units to print this and assigned color 9 to slot 1.  If you have 1  AMS you can assign the filaments based on the reference chart below. If you do not have Bambu Studio/Orca I recommend using it to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick.  

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. With 1 AMS when it gets to slot 4 in the print it will error and force a pause. You can then load the new colors (5-7) in AMS slots 1-3 then put color 4 back in and repeat this process by unloading color 4 when it is complete it will pause when it is time for color 8. With 2 AMS you can do the same above just with AMS slot 8. It will pause at 8 then you can load color  9 into your AMS slot 1. You don't have to let it force pause if you make it back in time to swap. This is handy if you are worried about missing the timing of a spool swaps. The black is only used once in this print which is why I chose slot 1 for color 9.

If you have any questions about printing this hit me up. 

AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.

MODEL COLOR - [1] [2] [3] [4] [5] [6] [7] [8] [9] 

1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2] [3] [4] [1]  

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [1] 

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [9] 

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.48mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you substitute filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA BambuLab Matte Charcoal Transmission Distance: 0.6
PLA PolyLite Blue Transmission Distance: 1
PLA Bambu Lab PURPLE Transmission Distance: 5
PLA PolyLite Azure Blue Transmission Distance: 3
PLA PolyLite Aqua Blue Transmission Distance: 2.5
PLA BambuLab Basic Jade White Transmission Distance: 5
PLA PolyLite Purple Transmission Distance: 0.7
PLA BambuLab Basic Pink Transmission Distance: 8.5
PLA Bambu Lab Magenta Transmission Distance: 3
This print uses 9 unique filaments

Swap Instructions:
Start with Charcoal
At layer #6 (0.56mm) swap to Blue
At layer #8 (0.72mm) swap to  Bambu PURPLE
At layer #9 (0.8mm) swap to Azure Blue
At layer #11 (0.96mm) swap to Aqua Blue
At layer #14 (1.2mm) swap to Jade White
At layer #15 (1.28mm) swap to Polylite Purple
At layer #16 (1.36mm) swap to Pink
At layer #18 (1.52mm) swap to Bambu PURPLE
At layer #19 (1.6mm) swap to Magenta
At layer #21 (1.76mm) swap to Jade White for the rest.

Stained Glass Sugar Skull - Filament Painting

Sugar Skull Stained Glass - Final 9 colors.stl

TIER 1 - You can print and use this display for retailing your bookmarks. 

TIER 2 - You can print and use this display for retailing your bookmarks. You can print the stands and sell them.  

This is a retail display stand I made for bookmarks. It can display 12 different bookmarks at the same time and is sized for 60x180mm bookmarks. There is also a space at the front that is recessed 2mm so that you can add a front deco plate which should be 200x50mm. The slots are at a 15 degree angle so the they have better visibility when it is displayed on a standard folding table. 

Printing: I printed this on a P1S. The tolerances were a little tight but I just used a rubber mallet and that took care of it. It will not come apart without a lot of force, but that is what I wanted as random people will be manhandling it. You can also print the bookmark holders and the 3 cross braces at ~99% uniform scale if you want the tolerances looser. If you do this make sure to scale your front deco plate by the same value (X/Y only) or it may be too big to for the recessed rectangle. 

Frame: Printed at 0.2mm layer height, grid infill @10%

Deco plate: This can be made as a Hueforge or a standard extruded model and printed accordingly. The one in the photo is a Hueforge I made quickly, and I will probably redo it and add the prices underneath the “3D Printed Bookmarks” text. 

If you have any questions just ask. 

Bookmark Stand - Retail Display 

BOOKMARK STAND V2.3mf

This is a Hueforge frame with 8 holes for 6x3mm magnets at the back for 100x100 (technically 108x108 read below) filament paintings. I have included two frames in this pack as the tolerance of the magnets I ordered varied a bit. One has holes that are 6.2mm and one has holes that are 6.3mm. I found that 4 magnets in the corners held really well on my fridge, but they are “rare earth magnets” so they may be stronger than some that others have hence the extra holes if needed. 

This model works like the 200x200 V2 larger frame in that the paintings are actually 108x108 after a 108x108x0.64mm plate is merged to the 100x100 Hueforge model. This allows the entire picture to be displayed within the frame and in this case allows for the frame to have a slimmer profile. 

Instructions:

Painting

Right click your build plate and add a primitive cube.

Non-uniform scale the cube to 108x108x0.64* (0.64 in my case. This should be equal to your “min depth” setting in Hueforge)

Import your 100x100 Hueforge Model

Center both the model and the primitive cube.

Merge/Assemble the two models.

Print with your trusty Hueforge profile and you should be good to go.

Frame

I printed it using the standard 0.2 Bambu profile which was 0.2mm layer height/15% grid infill and and two wall loops. You can cut  a portion of the frame with the holes in the slicer if you want to test your magnets in the different hole sizes. It might be worth putting a negative modifier cylinder all the way through the hole so you can pop it out easily. I had to hammer in the one with the 6.2mm holes and the ones with 6.3 were a little loose so I used some gorilla glue and let them set over night. I would recommend cutting the end off of a Q-tip and use it to apply the glue inside the holes very sparingly. 

If you have any questions hit me up. 

Hueforge Magnet Frame - 100x100 

100 x 100 - 8 holes - 6-2 hole for 6x3 magnets - FRAME.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

 This model was sponsored by Polymaker so I wanted to make something that really popped and was different from other Hueforge models. The depth on this one is pretty wild and is one of my favorites to date.  This complex color/low waste model uses 8 different Polymaker colors (13 instances). AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 2 different 3MF files for Bambu Studio. One for people with an AMS unit, and one for people with NO AMS with pauses already set (manual color changes). I used 2 AMS units to print this, and it definitely made it easy as many colors are reused. You can assign slots for 1 AMS and do manual spool swaps if you are up to it. Just pay attention to your color order and use the “Pro Tip” below.  If you do not have Bambu Studio I recommend using it to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick.  

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. With 1 AMS when it gets to slot 4 in the print it will error and force a pause. You can then load the new colors (5-7) in AMS slots 1-3 then put color 4 back in and repeat this process by unloading color 4 when it is complete it will pause when it is time for color 8. With 2 AMS you can do the same above just with AMS slot 8. It will pause at 8 then you can load colors 9-12 into your AMS slots 1-4. You don't have to let it force pause if you make it back in time to swap. This is handy if you are worried about missing the timing of a spool swaps.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you don't use my 3MF set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA PolyLite Black Transmission Distance: 0.3
PLA PolyLite Blue Transmission Distance: 1
PLA PolyLite White Transmission Distance: 5
PLA PolyLite Aqua Blue Transmission Distance: 2.5
PLA PolyLite Purple Transmission Distance: 0.5
PLA PolyTerra Sakura Pink Transmission Distance: 2.8
PLA PolyTerra Savannah Yellow Transmission Distance: 3.5
PLA PolyLite Pro Metallic Magenta Transmission Distance: 1
This print uses 8 unique filaments

Swap Instructions:
Start with Black
At layer #9 (0.8mm) swap to Blue
At layer #12 (1.04mm) swap to White
At layer #15 (1.28mm) swap to Aqua Blue
At layer #16 (1.36mm) swap to Purple
At layer #21 (1.76mm) swap to Sakura Pink
At layer #25 (2.08mm) swap to White
At layer #28 (2.32mm) swap to Savannah Yellow
At layer #31 (2.56mm) swap to White
At layer #35 (2.88mm) swap to Black
At layer #37 (3.04mm) swap to Metallic Magenta
At layer #41 (3.36mm) swap to Sakura Pink
At layer #45 (3.68mm) swap to White for the rest.

COTTON CANDY MONSTER - FILAMENT PAINTING

COTTON CANDY MONSTER AVAIL POLY ONLY FINAL 8 COLORS - 208x208.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

 This complex color/low waste model uses 10 different colors (11 instances). AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 2 different 3MF files for Bambu Studio. One for people with an AMS unit, and one for people with NO AMS with pauses already set (manual color changes). I used 2 AMS units to print this and assigned colors 9&10  into the AMS slots 2&3 (black i used twice so I didn't swap slot 1), and then just swapped them out when color 4 started printing. If you have 1  AMS you can assign the filaments based on the reference chart below. If you do not have Bambu Studio I recommend using it to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick.  

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. With 1 AMS when it gets to slot 4 in the print it will error and force a pause. You can then load the new colors (5-7) in AMS slots 1-3 then put color 4 back in and repeat this process by unloading color 4 when it is complete it will pause when it is time for color 8. With 2 AMS you can do the same above just with AMS slot 8. It will pause at 8 then you can load colors 9-12 into your AMS slots 1-4. You don't have to let it force pause if you make it back in time to swap. This is handy if you are worried about missing the timing of a spool swaps.

If you have any questions about printing this hit me up. 

AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.

MODEL COLOR - [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]

1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2] [3] [4] [1]   [2]   [3]  [4]

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [1]  [2]   [3]  [4]

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you substitute filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA BambuLab Basic Blue Gray Transmission Distance: 3.1
PLA PolyLite Stone Blue Transmission Distance: 0.5
BAMBU BASIC PURPLE Bambu Lab Basic Purple Transmission Distance: 5
PLA BambuLab Matte Ice Blue Transmission Distance: 3.5
PLA BambuLab Basic BambuLab Green Transmission Distance: 8
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA PolyTerra Savannah Yellow Transmission Distance: 3.5
PLA PolyTerra Sakura Pink Transmission Distance: 2.8
PLA BambuLab Basic Pink Transmission Distance: 8.5
PLA BambuLab Basic Jade White Transmission Distance: 5

Swap Instructions:
Start with Black
At layer #11 (0.96mm) swap to Blue Gray
At layer #13 (1.12mm) swap to Stone Blue
At layer #16 (1.36mm) swap to Purple
At layer #21 (1.76mm) swap to Ice Blue
At layer #30 (2.48mm) swap to BambuLab Green
At layer #33 (2.72mm) swap to Black
At layer #35 (2.88mm) swap to Savannah Yellow
At layer #39 (3.2mm) swap to Sakura Pink
At layer #41 (3.36mm) swap to Pink
At layer #44 (3.6mm) swap to Jade White for the rest.

Shark Graffiti - Filament Painting 

sharky 11 colors.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY (150x200)

This is a Hueforge filament painting of Dolphins using only 4 basic colors, that I created to showcase the Ultimate Hueforge Frame V2 150x200. This model has the 158x208 plate already assembled so you can just print this and the V2 frame  linked above and are ready to go. This is a quick 4 color print that can easily be done by people with or without AMS units. .

 

IMPORTANT: READ BEFORE PRINTING

I have uploaded two 3MF profiles. One for people with an AMS and one for people with NO AMS.

To print with 1 AMS units all you need to do is load the colors in order and print.

To print with NO AMS unit you just need to do manual filaments swaps every color. The 3MF is set to pause at the correct layer heights. At each pause load the next filament color in order by following your unload/load procedure for your particular printer, then hit resume. Repeat until complete. This will be once per color over the entire painting. You have a decent amount of time between swaps.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. There are some recommended speed changes in my 3MF files and a layer height modifier to print the first 0.64 mm @ 0.16 mm layer height to speed up the print as there is no blending on those layers. If you don't use my profile set your layer height modifier after you have set your color swaps/pauses as it changes the total amount of layers once sliced or use the layer height value instead that number will not change ex. at (0.88 mm) swap to Blue Gray.

Filaments Used:
PLA Polylite Black Transmission Distance: 0.3
PLA BambuLab Basic Blue Gray Transmission Distance: 3.1
PLA BAMBU CYAN Cyan Transmission Distance: 5
PLA BambuLab Basic Jade White Transmission Distance: 5

Swap Instructions:
Start with Black
At layer #10 (0.88mm) swap to Blue Gray
At layer #11 (0.96mm) swap to Cyan
At layer #15 (1.28mm) swap to Jade White for the rest

Dolphins at Sea - Filament Painting

Dolphins at Sea V2.stl

I had some requests for my Ultimate Hueforge Frame in different sizes, so here is the frame for 158mm x 208mm prints. The frame itself is 180mm x 230mm. I added a second hanger cutout to this one so you can hang it in either portrait or landscape. There isn't much weight to these so a finishing nail is all you really need to hang it. You only need one of the lock types per frame. The rectangular one is for thin prints to support all sides.

This frame is for my models in the members area only. It will not fit standard 150x200 prints as the prints are modified to be 158x208. The reason for this is so that the extra 4mm on each side rest inside the frame and therefore the full 200x200mm print is visible from the front. All models that use this frame will be clearly marked: “V2 Frame Only”. 

I will be adding models that fit this frame over time. If you want your own Hueforge models to fit this frame, follow the instructions below. NOTE: you will need to pay attention to the “Min Depth” setting in Hueforge. This setting is basically how thick it will print the base layers before starting to print the art in the base color. I use 0.64mm as I find that is a nice thickness to prevent bowing on models that have large amounts of the base color visible. 

    Create a plane/cube in your slicer that is 158x208x0.64mm (must be your min depth)
    Center the plane/cube. (Usually right click → Center)
    Import your Hueforge model (150x200)
    Center your Hueforge model. (Usually right click → Center) 
    Select both the plane/cube and the Hueforge model and assemble them. (Usually right click → Assemble)
    You are good to go. You now have a 158x208 Hueforge model that will fit this frame and make the full image visible. 

The hanger cutout is made so that prints with lob sided weight can be adjusted by using the teeth to easily level it. The frame is printed face down for a nice finish. Your plate type will determine the type of finish on the front side of the frame. I have used the gold textured plate that comes with the P1S in the attached photos.

 

PRINT and ASSEMBLY:

 

No supports needed. 3 wall loops and 0.16 Optimal layer height has provided the cleanest prints, especially the sides of the frame.

The locks can be printed with 2 wall loops and 0.20 Layer height. Print one frame and two straight locks or one rectangular one. The included 3MF has the settings above for their respective plates.

 

Place the frame face down on a surface that will not scratch it.

Orient your print face down so that the top aligns with the wall hanger cutout and insert it into the frame.

Insert one frame lock at a time and make sure you are pushing both ends in evenly. If you try to push one side at a time it will bind up. If you push one side in too far compared to the opposite side just flip it over and push it back out and retry until it is in properly.

It is a simple process and everyone that does not require a caution label on their coffee should breeze through it.

Ultimate Hueforge Frame - V2 - 150 x200

150x200 v2 final ALL PIECES.3mf

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

 This complex color/low waste model uses 10 different colors . AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 2 different 3MF files for Bambu Studio. One for people with an AMS unit, and one for people with NO AMS with pauses already set (manual color changes). I used 2 AMS units to print this and assigned colors 9&10  into the AMS slots 1&2, and then just swapped them out when color 3 started printing. If you have 1  AMS you can assign the filaments  based on the reference chart below.

If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. With 1 AMS when it gets to slot 4 in the print it will error and force a pause. You can then load the new colors (5-7) in AMS slots 1-3 then put color 4 back in and repeat this process by unloading color 4 when it is complete it will pause when it is time for color 8. With 2 AMS you can do the same above just with AMS slot 8. It will pause at 8 then you can load colors 9-12 into your AMS slots 1-4. You don't have to let it force pause if you make it back in time to swap. This is handy if you are worried about missing the timing of a spool swaps.

If you have any questions about printing this hit me up. 

AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.

MODEL COLOR -- [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]

1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2] [3] [4] [1]   [2]   [3]  [4]

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [1]  [2]   [3]  [4]

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. 

 

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA BambuLab Basic Blue Gray Transmission Distance: 3.1
PLA PolyLite Azure Blue Transmission Distance: 3
PLA BambuLab Matte Ice Blue Transmission Distance: 3.5
PLA BambuLab BASIC PURPLE  Transmission Distance: 5
PLA BambuLab Basic Pink Transmission Distance: 8.6
PLA PolyLite Magenta Transmission Distance: 1
PLA BambuLab Basic Orange Transmission Distance: 10
PLA BambuLab Basic Yellow Transmission Distance: 6
PLA BambuLab Matte Ivory White Transmission Distance: 4.4

Swap Instructions:
Start with Black
At layer #12 (1.04mm) swap to Blue Gray
At layer #16 (1.36mm) swap to Azure Blue
At layer #20 (1.68mm) swap to Ice Blue
At layer #24 (2mm) swap to White
At layer #28 (2.32mm) swap to Pink
At layer #32 (2.64mm) swap to Magenta
At layer #36 (2.96mm) swap to Orange
At layer #38 (3.12mm) swap to Yellow
At layer #44 (3.6mm) swap to Ivory White for the rest.

Australian Shepherd Puppy - Filament Painting 

puppy grafitti 10 colors - CLUB STL.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

This Hueforge model was created with separation of the foreground and background elements in mind to produce visually impressive depth . This complex color/low waste model uses 11 different colors (white being used twice which is color 12 in the 3MF). AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 2 different 3MF files for Bambu Studio. One for people with an AMS unit, and one for people with NO AMS (manual color changes). I used 2 AMS units to print this and assigned colors 9-12  into the AMS slots 1-4, and then just swapped them out when color 5 started printing. If you have 1  AMS you can assign the filaments  based on the reference chart below. 

If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. With 1 AMS when it gets to slot 4 in the print it will error and force a pause. You can then load the new colors (5-7) in AMS slots 1-3 then put color 4 back in and repeat this process by unloading color 4 when it is complete it will pause when it is time for color 8. With 2 AMS you can do the same above just with AMS slot 8. It will pause at 8 then you can load colors 9-12 into your AMS slots 1-4. You don't have to let it force pause if you make it back in time to swap. This is handy if you are worried about missing the timing of a spool swaps.

NOTE: The background color was actually supposed to be more of a very dark purple but the hex code for Overture Space  Gray was way off in Hueforge and it is more of a pale silver. I actually like the way this looks, but a dark tone would also work well. If you substitute colors results will vary.    

AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.

MODEL COLOR -- [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]

1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2] [3] [4] [1]   [2]   [3]  [4]

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [1]  [2]   [3]  [4]

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time.  

Filaments and Layer Swaps:

Filaments Used:
PLA Overture Space Grey Transmission Distance: 1.6
PLA BAMBU CYAN Cyan Transmission Distance: 5
PLA BambuLab Basic Jade White Transmission Distance: 5
PLA BambuLab Basic Pink Transmission Distance: 8.5
PLA BAMBU BASIC PURPLE Transmission Distance: 5
PLA PolyLite Magenta Transmission Distance: 1
PLA BambuLab Matte Charcoal Transmission Distance: 0.6
PLA BambuLab Matte Dark Red Transmission Distance: 1.4
PLA BambuLab Basic Red Transmission Distance: 5
PLA PolyTerra Pastel Peanut Transmission Distance: 0.5
PLA PolyLite Yellow Transmission Distance: 10
PLA BambuLab Basic Jade White Transmission Distance: 5

Swap Instructions:
Start with Space Grey
At layer #10 (0.88mm) swap to Cyan
At layer #14 (1.2mm) swap to Jade White
At layer #19 (1.6mm) swap to Pink
At layer #26 (2.16mm) swap to Purple
At layer #29 (2.4mm) swap to Magenta
At layer #31 (2.56mm) swap to Charcoal
At layer #35 (2.88mm) swap to Dark Red
At layer #39 (3.2mm) swap to Red
At layer #41 (3.36mm) swap to Pastel Peanut
At layer #43 (3.52mm) swap to Yellow
At layer #46 (3.76mm) swap to Jade White for the rest.

Monkey Business - Filament Painting

Monkey Business - Club V2 Frame _208x208.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

This Hueforge model is a product of many hours of meticulous color work resulting in an expanded pallet. This model uses 9 colors. AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included two different 3MF files for Bambu Studio. One for people with AMS unit(s) and one for people without AMS/MMU units.

[1 AMS/MMU Unit] Assign colors 5,6,7,8,9 to slots 1,2,3,4,1 respectively. In this case you will have to wait for color 5 (slot 1) to finish printing before you can put color 9 into that slot. If you are worried about missing swaps in the AMS you can remove spool 4 after it starts printing which will force a pause when it gets to that slot. 

[2 AMS/MMU Units] assign slots accordingly. Assign color 9 to slot 1 and swap out color 1 in slot one once it has completed and color 2 starts printing. 

[3 AMS/MMU Units] Assign all colors accordingly. 

[NO AMS/MMU] - preset pauses, manual color changes.

AMS SLOT GUIDE: The model colors will go in the following slots depending how many AMS units you have.

MODEL COLOR -- [1] [2] [3] [4] [5] [6] [7] [8] [9]

1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2] [3] [4] [1]

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [1]

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [9]

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA PolyLite Blue Transmission Distance: 1.1
PLA PolyLite Stone Blue Transmission Distance: 0.5
PLA BambuLab Matte Ice Blue Transmission Distance: 3.5
PLA BambuLab Basic Purple Bambu Transmission Distance: 5
PLA PolyLite Magenta Transmission Distance: 1
PLA PolyTerra Sakura Pink Transmission Distance: 2.8
PLA PolyTerra Savannah Yellow Transmission Distance: 3.5
PLA BambuLab Matte Ivory White Transmission Distance: 4.4

Swap Instructions:
Start with Black
At layer #12 (1.04mm) swap to Blue
At layer #14 (1.2mm) swap to Stone Blue
At layer #18 (1.52mm) swap to Ice Blue
At layer #22 (1.84mm) swap to Purple
At layer #26 (2.16mm) swap to Magenta
At layer #30 (2.48mm) swap to Sakura Pink
At layer #35 (2.88mm) swap to Savannah Yellow
At layer #39 (3.2mm) swap to Ivory White for the rest.

Graffiti Kitty - Filament Painting

graffiti kitty_Front_200x200.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

Woman on a Swing is a high detail Hueforge filament painting of the contemplation of the meaning of life. This model will only be available to club members. This model is done in traditional Japanese art style using 5 different colors. 

I have included two different 3MF files for Bambu Studio. One for people with AMS unit(s) and one for people without AMS/MMU units.

[1 AMS/MMU Unit] Assign color 5 to slot 1. Then manually swap out colors 1 for 5 once 2 starts printing. If you are worried about missing swaps in the AMS you can remove spool 4 after it starts printing which will force a pause when it gets to that slot. You can then swap color 1 for 5, feed color 4 back in and then you are good to go. 

[2 AMS/MMU Units] assign slots accordingly.

[NO AMS/MMU] - preset pauses, manual color changes.

If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA BambuLab Basic Red Transmission Distance: 5
PLA PolyLite Yellow Transmission Distance: 11 (**This is high TD**)
PLA BambuLab Basic Beige Transmission Distance: 8
PLA BambuLab Matte Ivory White Transmission Distance: 4

Swap Instructions:
Start with Black
At layer #12 (1.04mm) swap to Red
At layer #18 (1.52mm) swap to Yellow
At layer #26 (2.16mm) swap to Beige
At layer #30 (2.48mm) swap to Ivory White for the rest.

Woman on Swing -  Filament Painting

woman on swing - 5 color.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

This is a Hueforge Filament Painting of the king of the gods, Zeus, unleashing his wrath. This model uses 4 colors. This model will only be available to club members.

I have included two different 3MF files for Bambu Studio. One for people with 1 AMS and one for people with NO AMS (manual color changes). If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team. 

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA BambuLab Matte Charcoal Transmission Distance: 0.6
PLA BambuLab Basic Blue Gray Transmission Distance: 3.1
PLA BambuLab Basic Gray Transmission Distance: 2
PLA BambuLab Basic Jade White Transmission Distance: 5

Swap Instructions:
Start with Charcoal
At layer #14 (1.2mm) swap to Blue Gray
At layer #18 (1.52mm) swap to Gray
At layer #25 (2.08mm) swap to Jade White for the rest.

The Wrath of Zeus - Filament Painting

wrath of zeus - 208x208 - 4 color.stl

NON-COMMERCIAL - V2 FRAME ONLY

This model will only be available to club members. This is a filament painting of my favorite aspiring King of The Pirates: Monkey D Luffy using 6 colors. 

I have included two different 3MF files for Bambu Studio. One for people with AMS unit(s) and one for those without. 

[1 AMS/MMU Unit] assign colors 5/6 to slots 1/2 and manually swap out colors 1+2 for 5+6 once 3 starts printing

[2 AMS/MMU Units] assign slots accordingly.

[NO AMS] - preset pauses, manual color changes.

If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA PolyLite Red Transmission Distance: 1.5
PLA PolyLite Yellow Transmission Distance: 11
PLA BambuLab Basic Beige Transmission Distance: 8
PLA BambuLab Basic Orange Transmission Distance: 10
PLA BambuLab Matte Ivory White Transmission Distance: 4

Swap Instructions:
Start with Black
At layer #13 (1.12mm) swap to Red
At layer #20 (1.68mm) swap to Yellow
At layer #25 (2.08mm) swap to Beige
At layer #29 (2.4mm) swap to Orange
At layer #30 (2.48mm) swap to Ivory White for the rest.

One Piece - Luffy - Filament Painting

One Piece - Luffy 208x208 - 6 colors.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

Aurora Bearealis?At this time of year? At this time of day? In this part of the country? Localized entirely within your printer? This is an 8 color print of a floofy murder boi under the northern lights. This model will only be available to club members.

I have included two different 3MF files for Bambu Studio. One for people with AMS unit(s) and one for people without AMS/MMU units.

[1 AMS/MMU Unit] Assign colors 5,6,7,8 to slots 1,2,3,4 respectively. Then manually swap out colors 1+2 for 5+6 once 3 starts printing, then swap out colors 3+4 for 7+8 once 5 starts printing. If you are worried about missing swaps in the AMS you can remove spool 4 after it starts printing which will force a pause when it gets to that slot. You can then swap colors 1,23 for 5,6,7 respectively, feed color 4 back in and then when color 4 finishes swap it out for color 8. 

[2 AMS/MMU Units] assign slots accordingly.

[NO AMS/MMU] - preset pauses, manual color changes.

If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team.

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up.


Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA PolyLite Blue Transmission Distance: 1.1
PLA PolyLite Azure Blue Transmission Distance: 3
PLA BambuLab Basic BambuLab Green Transmission Distance: 8
PLA BambuLab Basic Yellow Transmission Distance: 6
PLA BambuLab Matte Ice Blue Transmission Distance: 3.5
PLA BambuLab Basic Beige Transmission Distance: 8.3
PLA BambuLab Basic Jade White Transmission Distance: 5

Swap Instructions:
Start with Black
At layer #14 (1.2mm) swap to Blue
At layer #21 (1.76mm) swap to Azure Blue
At layer #23 (1.92mm) swap to BambuLab Green
At layer #27 (2.24mm) swap to Yellow
At layer #30 (2.48mm) swap to Ice Blue
At layer #34 (2.8mm) swap to Beige
At layer #35 (2.88mm) swap to Jade White for the rest.

Aurora Bearealis - Filament Painting

Aurora Bearealis 208x208.stl

AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

The Hero of the Ages - Stained Glass is probably my favorite make of 2023. This model will only be available to club members. It was carefully and meticulously crafted to give a truly beautiful stained glass effect using 6 different colors. 

I have included two different 3MF files for Bambu Studio. One for people with AMS unit(s)

[1 AMS/MMU Unit] assign colors 5/6 to slots 1/2 and manually swap out colors 1+2 for 5+6 once 3 starts printing

[2 AMS/MMU Units] assign slots accordingly.

[NO AMS] - preset pauses, manual color changes. 

If you do not have Bambu Studio I recommend using it or Orca to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick. A lot of the settings are recommended by the Hueforge team. 

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the black. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. This one takes a while to slice on my old lappy so bear with it if you are using a slower setup. If you decide to resize this file DO NOT scale the Z dimension or it will fail to blend correctly. If you use different filaments results will vary. If you have Hueforge you can import the STL and see how different filaments will change the outcome before printing. If you have questions hit me up. 

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA PolyLite Blue Transmission Distance: 1
PLA BambuLab Basic BambuLab Green Transmission Distance: 8
PLA PolyLite Yellow Transmission Distance: 11
PLA BambuLab Basic Beige Transmission Distance: 8
PLA BambuLab Matte Ivory White Transmission Distance: 4
PLA PolyLite Yellow Transmission Distance: 11

Swap Instructions:
Start with Black
At layer #12 (1.04mm) swap to Blue
At layer #15 (1.28mm) swap to BambuLab Green
At layer #21 (1.76mm) swap to Yellow
At layer #23 (1.92mm) swap to Beige
At layer #26 (2.16mm) swap to Ivory White
At layer #28 (2.32mm) swap to Yellow for the rest.

Hero of the Ages -  Filament Painting

Hero of the Ages -  6 colors - for v2 frame.stl

This model is for my models in the members area only. It will not fit standard 200x200 prints as the prints are modified to be 208x208. The reason for this is so that the extra 4mm on each side rest inside the frame and therefore the full 200x200mm print is visible from the front. All models that use this frame will be clearly marked: “V2 Frame Only”.

You only need to print one lock type per frame. The square lock is for thinner prints that may bow when not supported on all sides. I rarely make thin prints so you should be good with the default lock in most instances with my models. 

If you want to modify my models in the non-member area, or your own Hueforge models to fit this frame, follow the instructions below. NOTE: you will need to pay attention to the “Min Depth” setting in Hueforge. This setting is basically how thick it will print the base layers before starting to print the art in the base color. I use 0.64mm as I find that is a nice thickness to prevent bowing on models that have large amounts of the base color visible. 

    Create a plane/cube in your slicer that is 208x208x0.64mm 
    Center the plane/cube. (Usually right click → Center)
    Import your Hueforge model
    Center your Hueforge model. (Usually right click → Center) 
    Select both the plane/cube and the Hueforge model and assemble them. (Usually right click → Assemble)
    You are good to go. You now have a 208x208 Hueforge model that will fit this frame and make the full image visible. 

I have included the 3MF for Bambu Printers as that is what I have. You can always open the files in the slicer and copy any other settings to your own slicer of choice if you wish.  

The frame is printed @ 0.16mm layer height w/ 3 wall loops. 

The locks are printed @0.20mm layer height w/ 3 wall loops. 

CUSTOM FRAME - v2 - 208x208.stl

This tier is for people that are looking to resell printed models that are specifically designated for physical good sales. To resell printed models you must have an active subscription. If you choose to stop subscribing your rights to resell printed models ends as soon as your paid period expires. 

Redistribution and resale of the digital files is not allowed, and subscribers acknowledge that Bedlam Threadz has the sole right to distribute, post and sell the digital files provided. 

This tier also provides for the ability to request specific models to be created. For requests under this tier models via request will be available to all club members. If you would like a private custom design you can always message me and we can work something out if you would like to retain the rights to specific artwork.  

Commercial Tier

This tier is for people that enjoy my work and would like to support my ongoing efforts to make high quality models. 

This tier allows access to all models that will be both exclusive and early access before public release. Models will be labeled accordingly and all early access models will be a minimum of 60 days prior to public general release. Some models will never be released outside of subscription tiers. This tier does NOT allow for commercial use of designated models. Personal use only. You may download and print these models, but may not sell prints or files and will not distribute any files in any manner. 

Supporter Tier

Airbender Graffiti - NO AMS.3mf

Airbender Graffiti - 2 AMS.3mf

Airbender Graffiti - 1  AMS.3mf

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Bedlam Threadz

Achievements

Seedling

Pinned models

Airbender Graffiti - Filament Painting

Airbender Graffiti - Filament Painting

Stained Glass Sugar Skull - Filament Painting

Bookmark Stand - Retail Display

Hueforge Magnet Frame - 100x100

COTTON CANDY MONSTER - FILAMENT PAINTING

Shark Graffiti - Filament Painting

Dolphins at Sea - Filament Painting

Ultimate Hueforge Frame - V2 - 150 x200

Australian Shepherd Puppy - Filament Painting

Monkey Business - Filament Painting

Graffiti Kitty - Filament Painting

Woman on Swing - Filament Painting

The Wrath of Zeus - Filament Painting

One Piece - Luffy - Filament Painting

Aurora Bearealis - Filament Painting

Hero of the Ages - Filament Painting

CUSTOM FRAME - v2 - 208x208.stl