AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY

This complex color/low waste model of Giraffe Graffiti uses 9 different colors (11 instances). AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.

I have included 2 different 3MF files for Bambu Studio. Please read all the instructions carefully.

For 1 AMS - There are 9 colors in this model with 11 instances. The black and purple are used twice. It is difficult to set this up on 1 AMS because of this, but might be doable. If someone does this successfully post the assignment setup in the comments.

For 2 AMS units - Assign filaments based on the chart below. Load the first 8 colors in order. When the Blue Gray (color 2) is complete swap it out for the White.

For 3 AMS units - Just assign the colors in order and print.

For NO AMS - pauses already set (manual color changes). Just go in the order below.

Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. This will force a pause when this spool is eventually called up for duty. The pause will be forced if any spool is not present when called for so in this case you can just un-feed spool 8, swap out the brown/blue gray [see chart below] when the pause occurs then re-feed color 8 [slot 8] back in and resume. With different models it may make sense to force the pause in other AMS slot[s] depending on the color swap order.

If you do not have Bambu Studio/Orca I recommend using it to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick.

If you have any questions about printing this hit me up.

AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.

MODEL COLOR - [1] [2] [3] [4] [5] [6] [7] [8] [9]

1 AMS - SLOT ---- N/A seems like this might be more complicated than NO AMS

2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [2]

3 AMS - SLOT ---- [1] [2] [3] [4] [5] [6] [7] [8] [9]

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. As with all Hueforges if you scale the model DO NOT change the Z dimension. If you substitute filaments results will vary. If you have Hueforge you can import the STL and see how substituted filaments will change the outcome before printing. If you have questions hit me up.

I use the TD-1 to measure my filament opacity which is why you see the names I have assigned to them in Hueforge. This gives me an accurate prediction. Filament TD can vary from brand to brand and even from spool to spool. If you want to measure you own for accurate predictions in Hueforge check out MY WEBSITE where I have official TD-1 units for sale.

Filaments Used: PLA BambuLab Matte Charcoal Transmission Distance: 0.6 PLA Bambu Lab TD-1 Blue Gray 2 Transmission Distance: 2.8 PLA BambuLab Matte TD-1 Ash Gray Transmission Distance: 0.2 PLA BambuLab TD-1 Yellow Transmission Distance: 5.3 PLA BambuLab TD-1 Purple Transmission Distance: 1.9 PLA Polylite TD-1 Magenta Transmission Distance: 1.9 PLA BambuLab TD-1 Cyan Transmission Distance: 2.3 PLA BambuLab TD-1 Pink Transmission Distance: 5.8 PLA BambuLab TD-1 Jade White Transmission Distance: 6 This print uses 9 unique filaments

Swap Instructions: Start with Charcoal At layer #9 (0.8mm) swap to TD-1 Blue Gray 2 At layer #11 (0.96mm) swap to TD-1 Ash Gray At layer #14 (1.2mm) swap to TD-1 Yellow At layer #20 (1.68mm) swap to TD-1 Purple At layer #24 (2mm) swap to TD-1 Magenta At layer #28 (2.32mm) swap to TD-1 Cyan At layer #33 (2.72mm) swap to Charcoal At layer #35 (2.88mm) swap to TD-1 Purple At layer #38 (3.12mm) swap to TD-1 Pink At layer #44 (3.6mm) swap to TD-1 Jade White for the rest.