I designed these to allow me to mount my Home Assistant Green on the side wall of the shelf the router sits on.  I printed two of the brackets, removed the bolts holding the heat-sink on, and replaced them with slightly longer (M3*20mm) bolts. Then I used wood screws (#4, 1/2") to attach them to pre-drilled holes on the shelf wall.

**Parts Required:**
- 4x M3*20mm bolts
- 4x #4 wood screws

Home Assistant Green Mounting Bracket

home-assistant-green-bracket v3.step

I wanted a way to mount the top half of a Surface Book 2 on a VESA stand, to use it as a Home Assistant control panel + monitoring display.  These models are attached with M3*10mm bolts to each other, positioned around the tablet, then the bolts are tightened to hold the tablet in place. 

You need once backplate, four rails, and four corners.  The backplate has holes spaced for a 75x75 VESA mount, and indents on the side facing the Surface Book for nuts — I'd recommend gluing them in, so they don't fall out during installation.

I printed mine in Bambu PETG Basic.  All the parts fit comfortably on a 256x256mm build plate, and could probably be squished closer for a smaller plate.

**Parts Required:**
- 8x M3x6mm bolts
- 8x M3 washers
- 12x M3 nuts

Surface Book 2 VESA Adapter (75x75)

backplate v4.step

A 2x1 gridfinity bin for storing two Bambu X1 hotends with the complete assembly attached.  Also has slots for storing the screws (2 per hotend).  I have a 0.2, 0.4, and 0.6 — this allows me to keep them all close to hand and easy to swap in and out of the machine without having to move the assembly between them.

Gridfinity Bin for Bambu X1 Hotend Assemblies

bambu-nozzle-gridfinity-block v2.step

A small storage bin I use to keep my deburring tool ([this one, by AFA Tooling](https://www.amazon.com/gp/product/B01L2XR4P2/)) next to my 3D printer, along with a handful of spare blades.

Gridfinity Bin for Deburring Tool (and blades)

deburring-tool-gridfinity-block v3.step

I printed two of these to attach my KVM from AV Access ([this one](https://www.avaccess.com/products/8ksw21dp-dm-displayport-kvm-switch/)) to the underside of my desk.  I used wood screws through the smaller holes to attach it to the desk, and reused the case screws that were holding the top onto the KVM through the slots and into their original holes.

Have to print two — one for each side.

AV Access DisplayPort KVM Bracket

KVM Bracket v2.step

A simple 90-degree stand for setting my FP2 up on top of a low shelf in my office.  The metal plate it attached to magnetically can be attached to the stand with a short #4 wood screw.  The larger hole allows the power cable to run through the back of the stand out of the way.

Aqara Presence Sensor FP2 Stand

aqara-sensor-stand v1.step

I recently printed [this](https://www.printables.com/model/566716-p1p-arc-ams-stand-riser-holder-x1c-p1s-easy-print/files) riser for the AMS on my Bambu X1C.  I wasn't a huge fan of having to pull the lid totally out each time I wanted to vent the chamber, so I designed these to use instead.

They're print-in-place and the center pole slides in and out, but can't be pushed all the way through in either direction.  One side is flattened to better hold the lid.

I printed mine in PETG; I tried a test run in PLA, but the clips didn't have enough flex to easily insert into the HSW on the sides of the riser.

Bambu X1C Sliding Lid Holder for Honeycomb Storage Wall

hsg-sliding-x1c-lid-holder v2.step

A gridfinity insert (5x7 units) sized to fit an IKEA Kvissle drawer.  I'd suggest pulling off the cork bases then gluing down the insert — I'm not sure if the drawer will still fit in the slides with both the cork and the insert installed.

The insert is fairly low-profile, and leaves about 60mm/2 3/8" of space between the top of the insert and the bottom of the drawer above (or top of the set).

I've noticed the Kvissle sets bowing out near the middle, causing the shelves to occasionally fall off their rails.  Mine are sitting in cubbies on an IKEA Kallax shelf, so I also designed some clips to hold the Kvissle sets in place and keep the walls from bowing outwards.  Those can be found [here](https://thangs.com/mythangs/file/989104).

I split the base in two for easier printing, with tabs to hold them together.  If the parts don't fit on your print-bed, please let me know in the comments, and I'll see if I can put together a version that's cut into smaller pieces.

The gridfinity bin featured in the first picture is the "Gridfinity Framework Laptop Expansion Card Holder" by Dayrl Biggins, and can be found [here](https://www.printables.com/model/319202-gridfinity-framework-laptop-expansion-card-holder).

The grid portion of this print was generated with the "GridfinityGenerator" plugin for Fusion360 by Lev Mishin, which can be found [here](https://apps.autodesk.com/FUSION/en/Detail/Index?id=7197558650811789).

Kvissle Gridfinity Insert

kvissle_gridfinity v3.step

After setting up some IKEA Kvissle letter trays on my IKEA Kallax shelves, I ran into an issue with the walls on the Kvissle trays bowing outwards and releasing/dropping the shelves.  These clips are designed to be attached to the interior walls of the Kallax shelves to prevent the walls of the Kvissle trays from bowing outwards, and keep the racks from sliding off the Kallax shelves at the same time.

They're designed to have one clip on each side of the Kvissle.

I printed mine out of PETG mostly as a test run for a PETG I hadn't used before, and so can't speak to their durability when printed out of PLA.

The step file has a 3mm countersunk (to 5mm) screw hole, to match the #4x1/2in wood screws I happened to have lying around in the garage.  

The attached f3d file has a set of parameters ("screw_hole_diameter" and "screw_hole_chamfer") if you need to adjust it for a different size of screw.  I'd avoid anything much longer than 1/2in or 8mm if you intend to mount more than one Kvissle side-by-side, as the interior Kallax shelf walls are only about 16mm thick.

The file also has parameters for the other dimensions, if you have any use for similar clips of different sizes.

IKEA Kallax-Kvissle Clip

ikea-kallax-kvissle-clip.step

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

timothy.s.dev

Achievements

Explorer

Seedling

Debutant