It's a tool that I use for composite material work, very useful to make proper fillet. Easy to replace after few uses.

A tool to make a fillet with epoxy. The first one is 25mm. I added one with 15 mm. The pictures are from the 25 mm.

A tool to make a fillet with epoxy. The first one is 25mm. I added one with 15 mm. The pictures are from the 25 mm.

A small but very useful set of gauges. I use it almost every day to measure corner radii.

this tool is to replace the epoxy tool when it breaks.

Measure more Fillet Diameters in mm using the Circular Tool

This is a Gridfinity-compatible holder for the v3 rocket fin fillet tools developed by RocketsAndRobots. There are two versions: one is minimal height (4u) and the other is stackable with the tools co

Measure the diameter or radius of a corner/fillet using this circular tool. Many of these types of tools use the easier to model semicircle, which may not be as useful as most corners, which ar

Male and female gauge for fillet to measure fillet from 1 to 10mm

Goes from 1/8" to 1" see image for list of all sizes. Perfect for a multicolor print!

Simple Fillet Gauge Tool from 1mm to 15mm diameter. For 16-26mm diameters, see https://makerworld.com/en/models/26533   For radius based measurements, scale 200%.   If you enjoy you can Buy

Simple tool to shape fillets on rockets without tape. v2 has a 45 degree chamfer on the fillet edge to help push excess epoxy down into the fillet as you draw it across the joint. It's a minor diffe

A small Kit Card style Epoxy mixing kit, with a spatula, a mixing stick and a foldable bowl.

A multi tool type fillet gauge with both inner and outer fillet gauges.

I was watching a video and found the image shown in this model to be a useful tool for woodworking. So I created it.

Epoxy Spreader with 0mm - 3mm - 5mm Teeth Useful tool for spreading epoxy over a surface to be bonded.

This is a Gridfinity-compatible holder for the v3 rocket fin fillet tools developed by RocketsAndRobots. There are two versions: one is minimal height (4u) and the other is stackable with the tools co

Here is a fillet tool I made for my modeling class. It has radi of 1-10mm

Tool for creating filleted joints with West System epoxy. V2 has the stiffener extended into the bulb. 2016-03-13 Have only used th 25mm V1 and it works fine.

Fillet / Round Measuring Adapter ! Important conversion factor! This tool is meant to be used with your vernier calipers extension thingie (see picture) . Radius = Caliper Reading x 2.414

Fillet radius tool

This is a simple 5.6"x 3/4" or 143mm x 19mm mixing stick / application tool. Used to finish corners with the rounded end.

Tray and mixer/applier for two component epoxy glue. Simple but handy. If you need small amounts of epoxy glue, you will probably need this.

Measure the diameter or radius of a corner/fillet using this circular tool.   Many of these types of tools use the easier to model semicircle, which may not be as useful as most corners, which ar

Simple Fillet Gauge Tool from 16mm to 26mm diameter. For smaller diameters (1-15mm), see https://makerworld.com/en/models/24330   Scale 200% if you prefer radius.   If you enjoy you can Buy

Sample prints of fillets in mm, can be used to find the rounding of a corner

First Remix, This is a radius finder attachment for your caliper

I'm building a CLC Teardrop Camper and realized that I didn't have fillet tools necessary for shaping the corner fillets throughout the project. I thought it might be a neat idea to try and recreate

Epoxy glue mixing tool. The maximum volume is 3 ml. But you can scale and create any volume.

I have altered the grate design from jrwknutson and created the opposite for inside fillets. "This is a set of fillet curves from 1mm to 20mm in single millimeter increments. I was tired of guessing

this fits inside the end of a frosting style piping bag and allows you to dispense the perfect amount of epoxy into your corner to join. the design mimics the 10mm radius of the west system fillet st

This is a set of fillet curves from 1mm to 20mm in single millimeter increments. I was tired of guessing incorrect radii during my design steps. These are labeled with Mayan numerical symbols because

I'll be doing a small stitch and glue project, and I needed a round fillet tool for my internal edges. Here they are!

These are for finding metric fillet edges

This is a basic tool to make unform fillet for rocket fins. It works for a tube diameter 10cm

I have altered the grate design from jrwknutson and created the opposite for inside fillets. "This is a set of fillet…

A lightweight mixing spatula and dish for mixing small amounts of two-part epoxy.

I created this tool because it is sometimes difficult to measure the corner radius on devices to fit a different design. I chose a common radius but I also attached the design on Solidworks 2019 if yo

Tool for mixing epoxy together with hardener. Spatula can be put in the bath.

1x1 Gridfinity compatible tool holder to consolidate many of the stock Ender 3 & Ender 3 Pro tools. Includes spaces for: All five allen wrenches (1.5mm, 2.0mm, 2.5mm, 3.0mm, 4.0mm) Small screwdri

A collection of tool holders for the Gridfinity system

I designed this tool holder array for holding larger pliers, wire strippers, wire crimpers and other tools securely to my multiboard withing arms reach of my workstation. The holes are 25mm diameter

This tool helps removing Multiboard snap fit inserts. It consists of a medium thread with a handle that can be used to leverage the snap insert out.

Gridfinity storage for nippers, scraper and cutting knife

Remixed to use the multiboard snap connector.

I liked the original tool holder from TIMBERA https://cults3d.com/en/3d-model/tool/creality-k1-max-toolholder-remix but wanted Gridfinity compatibility.

Deburring Tool, Pointed Tiles Cutter Pen, and 15 extra blade holder for the Gridfinity system

Storage for tools, glue, spare parts etc for the Bambu Lab Carbon X1C P1S and P1P*, designed for use with the AMS

Foam and 3D Printed parts to organize all your Milwaukee rotary accessories