The paracord finger pull on the door of my Eibos Easdry filament dryer broke pretty quickly, which made it really frustrating to open the door. I made this replacement finger pull that can be used instead. Note that the door on my unit is a very snug fit, so the spring latch is unnecessary. If your door does not fit snug, this part may not work for you.

To install, remove the door and pull the two halves apart. Start at two corners and then the rest should pull away fairly easily. Remove the latch and spring and put the printed part in as shown in the attached images. Snap the halves back together and you're good to go. Naturally, this should be printed in a filament that can handle heat. I'd recommend PETG at a minimum.

Eibos Easdry Replacement Door Finger Pull

EibosEasdryFingerPull.step

The Terran Republic's standard issue infantry melee weapon. Split into 4 separate pieces for clean, easy printing with minimal support. Any material will do. See photos for ideal printing orientations.
Toolless, glueless assembly! Parts should snap together. I printed mine in VoxelPLA PLA Plus and MatterHackers Build series PETG on a Bambu Lab X1C. If you are having fitment problems, I recommend using horizontal expansion (Cura) / X-Y size compensation (Prusa/Bambu/Orca slicer) on the Pin.
Nominal clearance: 0.1mm

Planetside 2 TR Chainblade

Chainblade_Assem.step

The New Conglomerate's standard issue infantry melee weapon. Split into 5 separate pieces for clean, easy printing with minimal support. Any material will do. See photos for ideal printing orientations.
Parts glue together for assembly.
Nominal clearance: 0.1mm

Planetside 2 NC Mag Cutter

MagCutter_Assem.step

The Vanu Sovereignty's standard issue infantry melee weapon. Split into the 3 separate pieces for clean, easy printing with minimal support. Any material will do. See photos for ideal printing orientations.
Parts glue together for assembly.
Nominal clearance: 0.1mm

Planetside 2 VS Force Blade

ForceBlade_Assembly.step

This is a static model of the repair and heal tools from Planetside 2. If you had never noticed, the heal tool is actually just a rail attachment for the repair tool.
Real picatinny rail is modelled for the top of the repair tool, which allows you to attach anything you want up there.
This is a static model, there are no moving parts.

Additional hardware: (heal tool only)
1x M3 nut
1x 10-20mm M3 screw
These are required for the picatinny attachment of the heal tool.

The rest of the kit friction fits together, but may require glue depending on your printer's calibration.

Planetside 2 Medical Applicator and Nano-Armor Kit (Heal Tool & Repair Tool)

Medical Applicator Assembly.step

The spawn beacon from the game Planetside 2. I modeled this up real quick because I thought it'd be funny, but then I realized I just don't want to print this lmao. It's a pretty simple print, though. I added the STEP file so you can edit it and hollow it out to hold whatever you want.

Planetside 2 Spawn Beacon

PS2_SpawnBeacon_Typ.step

This is a set of desk models that I created to be easily printable (as opposed to if you ripped the game files) and have turrets that can rotate and be interchanged. Requires only glue and no other tools to assemble. I recommend printing the snap-fitting parts (main turrets, vanguard and magrider cannons, secondary weapon bases) in PETG or a more flexible material than PLA. You can try them in PLA but I didn't make them for that.

Included are the following:

Magrider chassis (no main gun or secondary turret), both as one whole piece and a split version into two pieces with a joint (not sure what this is normally called) for printing. Also requires 2 large nodes and 4 small nodes be glued in. Weapons are Supernova PC, Perihelion VXC, V42 Pariah base and gun

Prowler chassis (no turret), both as one whole piece and a split version into two pieces with a joint (not sure what this is normally called) for printing. Prowler default turret with P2-120 HEAT cannon, Kingsnake turret with P4-120 Kingsnake cannons, M18 Palisade base and gun.

Vanguard chassis (no turret), both as one whole piece and a split version into three pieces with a joint that goes through all three pieces. Weapons are default turret with Titan-150 HEAT cannon, JGX12 turret, cannon, and separate antenna bit (because it breaks easily), N30 Trawler base and gun.

Planetside 2 MBTs (Main Battle Tanks) Magrider, Prowler, Vanguard with Articulating Turrets

Vanguard_Chassis_Whole.stl

This is my model of the U-100 Lastly, the standard issue sidearm of Nanite Systems Operatives in the game Planetside 2. I've split it into multiple parts for easier printing and painting. Some parts mechanically lock together, but most should be glued together.

The rail has been resized to actual picatinny rail dimensions.

I've just updated with files for the default optic. Like my other attachments, this requires an M3x0.5 8mm screw and 5.4mm wide nut.

Planetside 2 NSO U-100 Lastly Static Model Prop Handgun

Lastly_Assembly.step

This is the TX1 Repeater from Planetside 2, the default sidearm of the Terran Republic. This model has no moving parts, but has been split into multiple pieces for easier printing.

The rail is dimensionally accurate picatinny rail if that's your thing.

Planetside 2 TX1 Repeater Static Model

Lower

Upper

Side Pic Rail

Lower Pic Rail

Rear Sight

Reupload of my Thingiverse model with proper assemblies, etc.

This is my model of the MR-20 from the game Space Engineers, based on the original model by Natiq Aghayev. This one has details that are just normal-mapped on the in-game model.

I've changed the rail to be dimensionally-accurate picatinny rail, so you can mount an EOTech if that's your thing.

Space Engineers MR-20 Automatic Rifle Static Prop

Receiver

Fwd Dial

Rear Dial

Rear Lever

Barrel

Muzzle

Stock

Magazine

Midsection Fitting

Pin L

Pin S

Rail

Reupload of my other version as an assembly. Comes with the upper in two sections (barrel and slide) and as a single part.

Planetside 2 NC-6 Mag-Shot Static Model

MagShotMagazine

MagShotBarrel1

MagShotSlide1

MagShotBody1

MagShotSideRail

*PROP FIREARM, FIRES NO PROJECTILE*
This is the NS-45 Pilot from the game Planetside 2, with a spring-loaded slide, magazine release, and trigger, as well as a compliment of attachments.

This requires additional hardware to function. You will need an extension spring for the slide and small spring (like you can get from a pen) for the trigger and magazine release. Rods, such as in the breakdown pin in the grip and magazine release button, can be replaced with 3mm brass or steel rod for durability, but this is not necessary.

The attachments require M3 8mm screws and 5.6x2.4mm M3 nut for the sight and laser. I fit a 3V battery, button, and laser diode in the laser, but obviously you don't have to do this. It's modeled fairly specifically for my hardware, so leave a comment if you want the part numbers.

Planetside 2 NS-45 Pilot Prop with Attachments

Grip

Slide Rail

Trigger

Mag Catch

Slide Lock

Grip Cap

Trigger Retainer

Mag Catch Pin

Mag Catch Pin Cap

Breakdown Lever

Slide

Magazine Hollow

Magazine Solid

NS CCLR Sight

Scaled Pilot

Pilot Suppressor

Laser Sight

Laser Sight Pilot

Static model you can print and glue together. This is not a file rip, the model has been created from the ground up by me.

This is highly WIP; I haven't even printed it myself yet lol. Saving it for a deeper project. Please leave feedback if you try it! Like for real I don't even know if the scale is good

Length: 805mm (31.7")

NOTE: the pump handle needs to be fit on the handguard before the handguard is glued to the receiver. I'm trying to update the model to fix this but the site won't let me. Yay!

Changes from the original model:
1. Removed the coat hook thing on the right side
2. Centered the loading door in the model
3. Increased the size of the top cover for future project
4. Picatinny-accurate top rail

Planetside 2 NS Baron G5 - Static model

Planetside 2 NS Baron G6 - Static model

Handguard

Top Cover

Top Rail

BarrelProp

Pump Handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4838511.

This model is based on the pistol added to the game Space Engineers with the Field Engineer update. It comes as three pieces that can be adhered with glue, epoxy resin, etc., or it can be printed all at once. There is no function, it is just a static prop.

This contains an .STL for the whole pistol, and two sets of it broken into three parts for easier painting and modification. The first group uses the unnumbered grip and barrel, and "SEPWF_Frame_2"
This is the only one that I've printed, and there are some tolerance issues, though the set fits together well enough. I'm still investigating how the fitment issues are due to model tolerances versus print methods (all parts require supports).

The set with parts numbered "4" splits the barrel to reduce support usage on the barrel, but adds a seam through it. I haven't had time to print this version yet, though it should in theory fit together better.

Space Engineers 1:1 Warfare Pistol (Static)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4863733.

This is a set of gun attachments from Nanite Systems (Planetside 2) that have been modeled to be compatible with picatinny rails. You will need additional hardware: 12mm M3 screws, and 5.4x2mm M3 nuts.

These weren't made to be actual practical attachments for paintball/airsoft/firearms. Just prop attachments.

None of these have any added function, though I may add this and more attachments in the future.

The clamp used for the iron sights will also work with the grip and laser sight.

6/28/21
Added type 2 NS reflex sight. Uses same clamp as iron sights and laser.

6/3/23
Added NSO reflex sight from U-100 Lastly. Added d0ku NC 3.4x optic and reflex optic, so this isn't just an NS/NSO collection anymore lol.

Picatinny-Compatible Planetside 2 Weapon Attachments Assortment

Picatinny-Compatible NS Weapon Attachments Assortment

NSOSightBody_g1.stl

NSOSightClamp_g1.stl

NSOSightReticule.stl

Optic_Reflex.stl

Optic_Body.stl

Optic_Clamp.stl

Optic_Dial_Side.stl

Optic_Dial_Top.stl

Optic_Greeble.stl

Optic_Mount.stl

Optic_Reflex_Dial.stl

This is a model of the infamous medkit (skillstick) from Planetside 2, hollowed and fitted with a cap to store whatever you want.
Requires a 16mm long (5/8") piece of 3mm rod (brass, steel, etc.) for the hinge.

Planetside 2 Medkit Capsule

Main Cylinder_1.stl

THIS IS A PROP AND FIRES NO PROJECTILE

The S-10 is a handgun from the game Space Engineers. This model features a working magazine release, interchangeable mags, and interchangeable sights (using 5mm magnets).

The magazine releases uses a pen spring to function.

Space Engineers S-10 Modular Pistol Prop

B_Grip B.stl

I make models from games and stuff in CAD programs. Feel free to msg for requests!

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Terminal_6

Achievements

Seedling

Up and Coming