Power Supply Caddy for the Cooler Master Q300L case. You will need M3 Screws/Nuts to mount onto the case. NOTE - This does seem sturdy enough to hold the power supply at the top of the case but I set up the case to have the power supply at the bottom of the case. 

I have now added a v2 that seems a bit more robust (I still recommend having the PSU on the bottom) and can have heat inserts pressed in to make install a bit easier. you will need 3 M3 heat (5mm in length) and matching m3 screws. 

Part that uses heat inserts can be printed without supports but the part without the heat inserts will need supports. I printed with a .6mm nozzle and in PLA (though PETG may be a better choice due to heat inside of the computer case)

Cooler Master Q300l PSU Bracket

Power Supply Caddy for the Cooler Master Q300L case. You will need M3 Screws/Nuts to mount onto the case. NOTE- THis does seem sturdy enough to hold the power supply at the top of the case but I set up the case to have the power supply at the bottom of the case.

Will need supports and I printed with a .6mm nozzle and in PLA (though PETG may be a better choice due to heat inside of the computer case)

Cooler Master Q300l PSU Caddy

Q300l PSU Heat inserts.stl

Simple holder for the Rii I4 Mini Keyboard-- may fit others as well.

printed at a weird orientation with the bottom angle flat on the bed and with supports. 

used .6mm nozzle

Rii i4 Mini Keyboard Holder

To use with a Flashforge Creator Pro in order to help manual level the bed

.2 layer height is fine



Flashforge Creator Pro Bed Level

HDD Caddy for an Asus U43J. I looked on ebay to find a replacement and then thought about just making a slide that can just hold the HDD in place so it doesn't move around. I also used a bit of Neoprene adhesive on the door cover to help cushion it in more.

Fits quite tight.

I also printed with supports but you could probably get away with just bridging

.2 layer height is fine

Asus U43J HDD Caddy

I wanted to reuse the brass fitting from the old knob that had cracked. Not sure of the longevity of this but I used my solder iron and tweezers to press it in.

I also printed without supports with the top of the handle facing down on the bed.

.2 layer height is fine

Ender 3 Extruder Knob 

I wanted to experiment with Ergonomics of a vintage camera. I used double sided acrylic adhesive tape in order to affix the shells in place of the leather. Parts may need to be cleaned up depending how efficient your printer is.  

.2 layer height
Brim as the parts are sort of thin.
Supports

Pentax K1000 Camera Grip & Shells

I wanted to experiment with Ergonomics of a vintage camera. I used Double sided Acrylic Adhesive tape in order to affix the shells in place of the leather. Parts may need to be cleaned up depending how efficient your printer is.  

.2 layer height
Brim as the parts are sort of thin.
Supports fro some of the spots.

Pentax K1000 Shells

Cap for the switch on a Minolta Weathermatic D35. I have owned a few and they have broken. 

Fits quite tight.

I also printed with supports with the open part facing down to hide any imperfections.

.2 layer height is fine

Minolta Weathermatic Power Switch

Cap for the switch on a Minolta Weathermatic D35. I have owned a few and they have broken. 

Fits quite tight.

.2 layer height is fine

The previous ring seal was getting old and falling apart. Here is a new one. It is a bit tight fitting so it really seals well.

I did not print with supports.

.2 layer height is just fine

I know that it may not be food safe but I am not using it for food.

Swing Top Glass Bottle Seal

The previous ring seal was getting old and falling apart. Here is a new one. It is a bit tight fitting so it really seals well.

I know that it may not be food safe but I am not using it for food.

I was missing feet for my old metal Swingline stapler. These will probably work for other models of the Swingline staplers.

I did not print with supports.

.2 layer height is just fine

Vintage Swingline Stapler Feet

I was missing feet for my old metal Swingline stapler. These will probably work for other models of the Swingline staplers.

For use in Minolta Sub Cameras

I would recommend using a Black Filament and even after that try to keep out of direct sunlight.


I did not print with supports.

.2 layer height is just fine though smaller would be better

Fits a bit tight so I may edit it later. As for now it works.

Minolta Camera 16mm Film Cassette

Minolta 16mm Film Casette

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

RiClawson

Achievements

Seedling

Debutant

Trailblazer