Marcel R

Umea - a standing lamp in boho style

by
Geoshape
Follow
Follow
Remix Model
Geoshape
Geoshape
|
Image 4 of 20
Umea - a standing lamp in boho style 3d model
Geoshape
Geoshape
|
Image 4 of 20
Umea - a standing lamp in boho style 3d model
2D
3D
Makes
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style - Gave it some legs and a new hat - 3d model
Umea - a standing lamp in boho style - I made a smaller version. but no light bulb yet. - 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style - Hello,

Could someone please help me? My print of this lamp has failed for the third time. I am using PLA+ filament from the brand Esun. In the picture, you can see the failed print using Esun ePLA Matte. I have experienced the same results with PLA+ in white and blue as well. My settings in Bambu Studio are included in the picture.

Thank you in advance for your assistance. - 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style - Pretty nice! Love the design! - 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style - Very nice design. Unfortunately the shade was a little bit too big for my printer (Creality K1C) so I resized it to 87%. Also in France I didn't find wood rod in Leroy Merlin, so I bought wood shovels with a 26mm and it's almost nice. A little bit too big as you can see on the second photo, perhaps with a bigger top it could be nice. 
Finally I used a glow in the dark PLA filament so the lamp can shine all along the night :).  - 3d model
Umea - a standing lamp in boho style 3d model
Umea - a standing lamp in boho style 3d model
This model is restricted by licensing terms. 

Build your own modern standing lamp.

Fits a Bambulab X1 or P1 series

Changelog:

V2 has improved cable management. Retainer is changed and needs the cable tie files in addition to work. If you want to route a channel in one of the legs then use the "top v2" part and also print channel cover. "clip" is for keeping the cable in the channel, this must be adjusted to the measurements of your routed channel. Shade and Cap haven't changed.

Print settings: _Shade: _ prints in vase mode (0.8mm nozzle recommended; 0.4 possible) or normal mode (0.4mm nozzle) layer height 0.56mm (0.8mm nozzle) or 0.28mm (0.4mm nozzle) in both cases print it upside down and set bottom layers to 2 (0.8) or 4 (0.4) 2 options for 0.4mm nozzle: vase mode: set line width to 0.7/0.8mm; 4 bottom layers normal mode: 2 walls; 4 bottom layers; 0% infill; 0 top layers add height range modifier: 0.96mm to 300mm --> 0 bottom layers

Top: prints upside down 0.2mm layer height 3 walls minimum Cap: 0.2mm layer height 2 walls 1 bottom layer 0 top layer 30% gyroid add height range modifier: 0% infill after 1mm

Filament: For the shade use some whiteish filament. I used Spectrum PLA Ivory Beige.

Additional hardware: 3x wood rods diameter=28mm L=1370mm 6x wood screw 3,5mm 1x zip tie 1x E14 or E27 light cord


364 Likes704 DownloadsAugust 25, 2024


364 Likes704 DownloadsAugust 25, 2024
This model is restricted by licensing terms.