Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035897.

Wall mount pieces for Lego set 92176 Saturn V Rocket. 

2-piece set to vertically mount Lego Saturn V rocket.

    Print WallBase piece with the wall facing side on the bed (No supports required)
    Print TopClamp piece flat with long arms parallel to printer bed. Supports may be required for the screw hole depending on your printer setup. 

Rocket set sits on WallBase part and TopClamp fits securely near the top of the middle section.
Secure WallBase to surface with appropriate fixings first, then TopClamp piece can be secured once suitable position has been marked.  

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 
 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

 Lego 92176 Saturn V Wall Mount (Vertical) 

TopClamp.3MF

TopClamp.SLDPRT

TopClamp.STL

WallBase.3MF

WallBase.SLDPRT

WallBase.STL

Stand for 75356 Executor Super Star Destroyer

2-piece set to display the Lego set.
Lower then original stand and displays set broadside at angle of printed Arm piece.
Designed for use on a high shelf to show more of the top side then the underneath.

Files included for 0°, 5°, 10°,12.5° and 15° angled arm pieces (rough estimate for angle)
Pictures show set displayed with 15° Arm piece. 

2 pieces to be printed, Arm piece slots into tabs on Base part.

    Print Base piece with flat piece on printer bed.
    Print Arm piece with large open square on printer bed and tabs facing upward. 


Use's both 2x4 Lego plates from the original stand to connect to underside of the SSD set. 
These fit snugly into the open square on the Arm piece (May require slight shave if any elephants foot style issues on printer)

Existing triangular side pieces need to be moved out to allow the stand to sit flush to the SSD.  (example pic shown)


I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells recommended. 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

 

UPDATE: 26-May-2023

Added additional Arm pieces at 0°, 5°, 10° and 12.5° degrees (rough estimate)
Original piece is around 15°

 Lego 75356 Executor Super Star Destroyer Low Stand 

Arm_5.3mf

Arm_5.SLDPRT

Arm_5.STL

Arm_10.3mf

Arm_10.SLDPRT

Arm_10.STL

Arm_12-5.3mf

Arm_12-5.SLDPRT

Arm_12-5.STL

Arm_15.3mf

Arm_15.SLDPRT

Arm_Plate.SLDPRT

Base.3mf

Base.SLDPRT

Base.STL

SSD Mount.SLDASM

Arm.STL

Arm_0.3mf

Arm_0.SLDPRT

Arm_0.STL

Description

Wall Mount for Vertical Stand available for Lego 75192 UCS Millennium Falcon.

Designed a wall mount for use with a modified Vertical Lego stand available for the 75192 UCS Falcon. (Search for Efferman Vertical Stand here, or amazon link for the knock off here) 

Stand working well now after finally building the Falcon set and mounting it.
Saves a bit or space as doesn't protrude out as much as an angled display.
Set seems to be mounted very firmly with no issues. 
Have updated post with pictures of the Falcon mounted.

Minor modification required to rear legs of stand, no additional pieces required only change in layout. Removes rear two feet pieces and alterations to support framework. 
All changes shown in pictures. 
This modification was to save some space and display the Falcon at a slightly more upright angle. (Changes by about 20 degrees) 

Print two of the wall mounts and mount securely to wall, 2x screw holes in each mount.
Vertical Stand sits snugly into mount from above.
Stand front foot piece aligns with wall mount cutout, and protruding nub sits in the gap in front of the front upright. 
Rear nub on wall mount sits into the hole in front of the rear upright.

Printed parts in PETG, mounts laying on their side on the print bed.
Supports only required under Front Cut Out and Nubs. 
Used a 0.6 nozzle and 0.3mm layer height, 25% Infill and 6 shells all around. 
Recommend printing with a brim if you have any adhesion or warping issues. 

Used some cable ties to tidy the USB cable running to the Falcon for the light kit so wrapped them around the stand and on to the support to be extra sure, but was mounted for several days without them with no issues.



 Lego 75192 UCS Millennium Falcon Vertical Stand Wall Mount 

WallMount_20_10.3mf

WallMount_20_10.SLDPRT

WallMount_20_10.STL

Made up a wall mount for the 75367 UCS Venator, display the ship at 90 degrees rather then usual 45 degrees. (Due to available mounting space restrictions)

Makes use of some of the technic pieces from the sets included stand, I also suggest some additional bolts or cable ties to add additonal support to be sure. 

Not for the faint hearted, make sure all the pieces are FIRMLY attached before mounting.

The wall pieces are mounted on the wall with the protruding section sticking out to allow the winged section of the stand to slot down into the gap. 
(Reference Model picture shows Rear stand in Blue with the Wing section in Yellow, the Wall Piece is in Red)

With the Front and Rear Stand pieces attached to the Set, and the wall pieces mounted, the set can be slid down into place between the wall and the wall pieces. 

Print four of the Wall Pieces and one each of the Front Stand and the Rear Stand pieces.
Wall pieces have integrated screw holes for mounting.
Stands have slots that fit some of the Technic (holed) pieces (I think 12 studs in length is the best option, I had to use some shorter ones for the front stand and bolted them together)

Printed in PETG, Wall pieces were printed on their side with the narrow edge on the print bed.
Stand pieces were printed with the flat side on the print bed.
Used a 0.6 nozzle and 0.3mm layer height, 25% Infill and 6 shells all around. 
Recommend printing with a brim if you have any adhesion or warping issues. 

The Stand is holding the set firmly but I do suggest some additonal supports to be sure (eg Bolt throught Technic pieces or similiar)
I also suggest using some small lego parts as fixing to hold any loose or rising hull sections together to make a cleaner display. 

LEGO Star Wars 75367 UCS Venator Wall Mount 

RearStand.3MF

RearStand.SLDASM

WallPieces.3mf

WallPieces.SLDPRT

FrontStand.3MF

FrontStand.SLDASM

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

ColLynch