Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035897.

Wall mount pieces for Lego set 92176 Saturn V Rocket. 

2-piece set to vertically mount Lego Saturn V rocket.

    Print WallBase piece with the wall facing side on the bed (No supports required)
    Print TopClamp piece flat with long arms parallel to printer bed. Supports may be required for the screw hole depending on your printer setup. 

Rocket set sits on WallBase part and TopClamp fits securely near the top of the middle section.
Secure WallBase to surface with appropriate fixings first, then TopClamp piece can be secured once suitable position has been marked.  

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 
 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

 Lego 92176 Saturn V Wall Mount (Vertical) 

WallBase.3MF

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035887.

Wall mount pieces for Lego set 40591 Death Star 2 

1-piece set to wall mount Death Star with parts from its included stand.

    Print WallMount piece with the large hole in the cylindrical piece facing upwards.
    Supports may be required for the screw hole depending on your printer setup. 

Secure WallMount to surface with appropriate fixing.
Remove the existing lower piece of the Death Star mount, leaving the round pieces connected to base of the Lego set.
Slide the round pieces into the hole in the cylindrical part of the mount and affix the Fully Armed and Operational Battle Station atop the round pieces. 

Hole in bottom of cylindrical piece to allow for the grey bar piece that runs through the round pieces.

I printed the part in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 
 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

Lego 40591 Death Star 2 Wall Mount 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035892.

Wall mount pieces for Lego set 75355 UCS X-Wing

3-piece set to mount Lego set to the wall. 
Wall mount is angled in a way to show X-wing in flight, with enough clearance to allow all S-Foils to be locked in attack position. 

3 pieces separated to allow for easier printing, and because I messed up the initial clearances and a third part was the quickest way to fix it.

    Print BackPiece on its side with screw holes parallel to print bed.
    (Supports may be required for screw holes depending on printer settings.)
    Print WallMount on its flat side .
    Print WallPiece with largest hole flat on the print bed.
     

Secure WallPiece part to the wall via suitable fixing. Larger hole should face outwards to allow for head of screw/both to be hidden in rounded area.
Slot BackPiece into WallMount piece and align with WallPiece, 2 holes can be used to secure both pieces together with a suitable small nut and both. 

Lego set sits securely atop the WallMount piece, the larger upright fits into the existing mount hole on the bottom fuselage of the set. Two additional smaller uprights fit snugly at the front and rear of the lower fuselage. 

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells recommended. 

 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

Lego 75355 UCS X-Wing Wall Mount 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035889.

Wall mount pieces for "unreleased" Lego set 42113 Bell-Boeing V-22 Osprey.

3-piece set to mount Lego set to the wall. 
Wall mount is angled in a way to allow clearance for all moving parts (Rotors,Engines, etc.)
 

Hook and Cross piece separated to allow for easier printing.

    Print Hook on its side.
    Print Cross with Prongs facing upwards.
    Printed AngleWallMount with the screw holes on bed.
    Supports may be required depending on printer settings.

Secure AngleWallMount part to the wall via suitable fixings.
Hook and Cross piece slot into AngleWallMount part and can be secured further with a small nut and bolt at the hole where all 3 parts intersect. (Not required but suggested to lock set into wall mount)

Lego set sits onto Hook and Cross piece and slide's forwards to lock in place.
Hook piece goes into slot between battery compartment and lower fuselage.
Cross piece uprights slot into gaps behind rear wheel wells. 

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 

 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

Lego 42113 Tilt-Rotor Wall Mount 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035883.

2 Position upright  stand for Dell Latitude 5580 laptop.

Laptop stand with 2 separate positions for the laptop to slot into.
This is primary for raising the height of the laptop screen to a more ergonomic position.
Most suitable for use with an external mouse and keyboard, however laptop keyboard/touchpad is still fully usable in either position.
 

Print the stand model with flat on the printer bed with the 4 inner slots facing up/down.
Print the model twice for right and left hand side parts.
No supports required.

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells recommended. 

Dell Latitude 5580 Upright Laptop Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4840830.

### Set of Legs to hold Asus MB169C+ Monitor.

Designed for use with Dell Latitude 5591 Laptop, because the included folding cover/stand is a nice cover, but a terrible stand.
One leg has an opening to allow the USB-C cable connection.
Holds screen at the same height as the main display at an angle of 80 Degrees.
Additional set uploaded to work with Dell XPS 15 (2019) at an angle of 70 Degrees. 

Pictures show parts printed on PrusaMk3 with 0.6 Nozzle using Urban Grey Prusament PETG.

_Original Solidwork part files included if you would like to further edit the parts._  

[Monitor](https://www.asus.com/Displays-Desktops/Monitors/ZenScreen/MB169C-plus/)


Asus MB169C+ Stand

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships