This is a chimera of the head of [this dromedary](https://www.thingiverse.com/thing:1902866) and the body of [this camel](https://www.thingiverse.com/thing:3302407).

Vero cammello (True camel)

vero_cammello.blend

This is a model I designed to repair my motorcycle top box. The plastic hook snapped in two because of its age, so I decided to learn how to create parts in FreeCAD, and here we are. I have happily restored my top box with this 3D printed part, with some post-processing that I detail below:

- the 5 holes for the two metal rods came too narrow and the rods wouldn't fit; you can enlarge them a bit on the computer or with a drill
- the 5 holes need some lubrication to work well
- the small hole for one of the two springs didn't come out well with my 3D printer; I drilled it with a small tip; be sure to drill in the central body and not too close to the edge
- the hook may not be very effective, due to swelling of material during 3D printing near sharp edges; I removed material under the hook to make it more effective; also, notice that this hook is straight, while the original piece has a curved edge; I tried to sculpt it with a knife but it's sufficiently effective as it is

Always remember to take photographs of the original disposition of pieces as you disassemble the top box, and store all of them in a dedicated box. Happy repairing and happy motorcycling!

Hook part for Givi Flow top box

03_gancio_bauletto.3mf

This Remix of onehand_bookholder_mah.stl by marethyu simplifies the letters for a better result on my 3d printer

Remix of onehand_bookholder_mah.stl

If you liked our model, please support us [donating](https://ko-fi.com/plasticdreams) or [purchasing the model](https://cults3d.com/en/3d-model/art/pyke-ashen-knight-mask).

The main author of this model is [@amiprocedural](https://www.instagram.com/amiprocedural/), with contributions by me.

**3D model description**

This is a original cosplay adaptation of the Ashen Knight skin of Pyke from League of Legends.

The mask has channels on the inside into which to thread an LED strip to illuminate the inner eye area.

It is intended as a base for cosplay creators to paint and complete with grommets to rest on the face and elastic bands to hold it in place.

**3D printing settings**

It is recommended to print the mask vertically. For small printing planes, you can tilt it slightly and use supports. The height of the layers can be very high, even 0.48 mm, as there is a post-processing phase in which to sand the surface and apply a primer for painting.

Pyke Ashen Knight mask

pyke_ashen_knight_mask_base.stl

La celeberrima legge di Murphy. Questa stampa in PLA bianco e ottanio la recita incisa, insieme alla raffigurazione del suo primo postulatore, Edward Murphy, realizzata con tecnica di litofania.

Progetto modellato e stampato su commissione di SbS Group srl in collaborazione con [@amiprocedural](https://www.instagram.com/amiprocedural/)

Legge di Murphy - piedistallo

murphy-base.stl

Remixed from [Lenovo Legion Y720/520 keycap](https://www.thingiverse.com/thing:4617181).

Sliced at 0.2 mm layer height, with 0.4 mm nozzle. I increased retraction length and retraction speed to reduce stringing with PETG, and lowered a bit the temperature and print speed.

To make sure thin perimeters are printed, I set the "minimum perimeter width" to 25% in Prusa Slicer, otherwise there were hollow gaps.

**TODO** The shoulder of the pin can be extended above the border to make it sturdier.

Lenovo Thinkpad T460 keycap

Remixed from [Lenovo Legion Y720/520 keycap](https://www.thingiverse.com/thing:4617181)

This is a copy of https://www.thingiverse.com/thing:4236739 modified to flatten the soles of the shoes; previously the model printed resting only on a few points.

Umarell lavori in corso (flat feet)

This model is remixed from [Fishbone - Jinx - League of legends (LoL)](https://www.thingiverse.com/thing:4500565) on Thingiverse.

This version has two relevant differences that make it more print friendly with FDM printers:
- it is split in half to lay the flat part on the bed;
- all the thin parts of the model are made thicker.

Fishbone

This is reworked from [Ender 3 v2 Filament Guide Clip — Snug Fit](https://www.thingiverse.com/thing:5191383) without the ribbon nearest to the user. I needed that because that part of the aluminum profile is occupied by a LED rail.

Endclip for Ender 3 with three ribbons

Quarter moon outline with Voronoi pattern inside. It comes in two variants:
- wireframe (moon.stl)
- wireframe + 2 x subdivision surface (moon_sub2.stl)

The inside is slightly raised relative to the outline and that made my first print fail. I lowered the model in the slicer until the inside touched the bed to fix the issue.

Inspired by https://www.thingiverse.com/thing:2215079

Geometry Moons: these are generated with Blender's Geometry Nodes. I have a basic pattern that gets generated every time differently, just changing a numerical seed. So every moon I print is unique.

Voronoi Moon

moon.stl

geometry_moon_199.stl

Dado giochino

dadogiochino.stl

This phone stand is inspired by:
- https://www.thingiverse.com/thing:2120591
- https://www.printables.com/it/model/40471

It is made taller to accommodate USB C plugs. Designed in collaboration with [AMI Procedural](https://www.behance.net/aldomariaibello).

Ophn Phone Stand

This model fixes irregularities with vertices in the original by kallend on Thingiverse:
https://www.thingiverse.com/thing:3234289

In particular, with the help of [AMI Procedural](https://www.behance.net/aldomariaibello), we used the weld modifier to fix misaligned faces and removed the vertex floating in the middle of the model.

FCC Brillouin Zone (fixed)

This model fixes irregularities with vertices in the original by kallend on Thingiverse:
https://www.thingiverse.com/thing:3234289

In particular, we used the weld modifier to fix misaligned faces and removed the vertex floating in the middle of the model.

A small printable to test lenght fidelity along axes, light overhangs and curves.

Lenght values may be found in the Blender file, using the MeasureIt add-on.

This piece was made in collaboration with https://www.behance.net/aldomariaibello

AMI's tolerances cube

This is a modified version of the holder by ZenziWerken. One side is smaller to make it easier to move the thumb away when changing page.
Derived by https://www.thingiverse.com/thing:2105202

Asymmetric One Hand Book Holder

[PONYS](http://www.ponys.unina.it/) (Physics and Optics Naples Young Students) Logo on a square. This is a first test to make a hanging charm. Future versions might include a hole or a ring to pass a string.

PONYS Logo

This is a modified model of the Spaceship Token from [Entanglion](https://entanglion.github.io/) board game.
It features a hole to pass a string into and use the piece as a charm and thicker legs, as in the original piece they kept breaking.

Entanglion Spaceship Token (soft mod)

A student going indie on 3d printing. If you want to support what I do get in touch or offer me a beer at: https://ko-fi.com/plasticdreams

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

soffice

Achievements

Seedling

Novice Maker

Trailblazer

Up and Coming