Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6084692.

I modified the Spaceship Earth model to hold an Amazon Echo Dot (2nd gen). Holes were added to let sound out of the bottom mounted speaker and a hole was added to access the USB and audio jacks on the back side.

To align the cover with the pattern on the base, align the hole that cuts down through the bottom of the cover with the center of the USB/audio cut-out on the base. See photos.

The base can be printed in either orientation, both require supports. I printed it upside down so the supports were on the interior.

The cover should be printed right side up. The interior cavity is conical to avoid supports and reduce filament. The conical section inside has an overhang, so be mindful in your slicer.

Remixed from "Spaceship Earth from Disney World's Epcot" by SnickerdoodleFP, Thing:3084118 (full Spaceship Earth STL)
https://www.thingiverse.com/thing:3084118

6/19/23: Added STL file of design (same as original OBJ file)

6/26/23: Added STL for top half. Holes added (similar to base) to allow sound to reach the microphones on the Echo. The holes also allow the light ring to be visible.

7/15/23: Added STL for a base with no sound holes, intended for those that don't use the internal speaker. Make sure you download the correct one. If you use the internal speaker use the "with sound holes" STL. The cover STL will work for both base versions.

Epcot Spaceship Earth Amazon Echo Dot 2nd Gen Stand with Cover

Epcot Spaceship Earth Amazon Echo Dot 2nd Gen Stand

Spaceship_Earth_for_Echo_Dot_w_Sound_Holes.stl

Spaceship Earth for Echo Dot w Sound Holes_Cover.stl

Spaceship Earth for Echo Dot NO Sound Holes.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6108816.

This chip clip design uses an actual 3D scan of a set of teeth for the jaws. The clip assembly is 100% 3D printed, the spring clip needs to be printed twice (1 for each side). The spring clips slide into the grooves on the jaw and roof, slide them unit the groove on the spring engages with the retention hump inside the groove (there will be a click).The clips will need to be opened slightly to get them in place. I measured about 1 kg of clamping force, however, the force will ultimately depend on the material used for the springs.

Each STL is a single body. Reorient the parts in the slicer so that the large flat surfaces are against the bed - teeth pointing up. Print the springs on the side. The multicolor print was made in PrusaSlicer 2.6.0 using the new "multlimaterial paint" feature. The PrusaSlicer 3mf file is included with the teeth painted to make that step easier.

I recommend printing the springs with PETG because PLA will lose its springiness over time since it is under constant load. 

I also included an Step file of clip assembly without the teeth for easier remixing.

Mouth Chip Clip from 3D Scan of Teeth

Jaw.stl

Jaw_Roof_PrusaSlicer_2.6.0_Multicolor_P2PP.3mf

Roof.stl

Spring.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6108929.

Pokemon Poke Ball style wall plate for Leviton Decora rocker style light switch or outlet. Similar dimensions as the off-the-shelf wall plate:
https://www.homedepot.com/p/Leviton-Decora-1-Gang-Wall-Plate-White-R52-80401-00W/100036991

This is designed to be a multi-material print. I printed this using a Mosaic Palette 2 and was sliced in PrusaSlicer with P2PP. It was printed with the face against the build plate to avoid using supports.

Individual STL files are provided for each part. The 3mf file contains all 4 parts. Step (.stp) and Fusion 360 (.f3d) files are included for easy modification.

Pokemon Poke Ball Wall Plate for Leviton Decora Style Switch and Outlet

Pokeball Wall Plate for Leviton Decora Style Switch and Outlet

Pokeball_Wall_Plate_All.3mf

Pokeball_Wall_Plate_Face_Border.stl

Pokeball_Wall_Plate_Face_Lower.stl

Pokeball_Wall_Plate_Face_Upper.stl

Pokeball_Wall_Plate_Plate.stl

https://www.thingiverse.com/sj3dprints/designs

https://www.printables.com/@sj3Dprints_417557

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow