I wanted one that I could quickly remove the supply from as it's on a long cable, and I often take it with me (plugged in or not). Command strips seemed like a better solution to screws but I included holes for a couple of those too, just incase. The strips "cavity" is recessed so you can get to them as I use the hook and loop ones and might not want to break off the bracket when moving stuff about later. 

The print that's in the photos is in A Olive Green PLA+ Matte or something like that, its not great to print with for me 80% of the time, particularly at height for stuff like this, hence the nasty stuff, I didnt want to reprint because I really dont need to make any changes so glue it was! I dont -think- it was the model's fault, but your milage may vary. 

Anker 5-port Power Supply Bracket for Command Strips 

power_supply_bracket_command_strips.stl

Honestly, not sure what these are called without needing to Pay More Attention With Class. I recently stuck another notebook of sticker release paper in my Midori MD Notebook, And It has gotten Kinda Bulky. So I added a band, but because of aforementioned THICC I needed a way to keep it from digging into the notebook cover. So 4 birds one stone??? Theres a channel on these clips that allow the band to pass through. Your bandage may vary. 
The holes are not centred so that when its tied as the photos show, the band travels through the channel correctly rather than pulling itself out a bunch. 

Print standing on its short side so the layers are against the forces from the page, your band aint gonna be cutting through the clips and its worth the extra half a gram for the brim. 

Band/Edge Protection For Notebooks

EdgeProtection_v1_WithHoles.stl

Its got everything you'd want except a lip! These bins can store in each other and are roughly the same size and shape as a 1x1 Gridfinity cell, and will fit baseplates AND can have magnets. What more could you want? (If you want more sizes just let me know).

I made this because I find myself using bins as very temporary sorting bins, it would be nice to not waste cells on empty containers in waiting, maybe you feel the same. 

Be careful removing them from the bed, printed at around 0.2 layer height, i'm sure that it would be fine at bigger heights, but I just wanted 2 so im not wasting cells or knocking them over. 

Gridfinity Compatible Nesting Bin 1x1x6

NestingGridfinityCompatibleBin1x1x6.stl

I mean, what do you expect? Complete with magnet holes, I recommend glueing in place the magnets. I'm sure there will be a use for this. I've added 3 sizes right now for bands, 18mm, 20mm and 22mm. I'm sure there are other sizes of bands too. I'll add them in due time. Those were just the ones that stuck in my mind, drop a comment if you need another size and ill go do it. 

Gridfinity Wrist Baseplate 1x1 

gridfinity_wrist_mount_v1_22mm.stl

gridfinity_wrist_mount_v1_20mm.stl

gridfinity_wrist_mount_v1_14mm.stl

gridfinity_wrist_mount_v1_16mm.stl

A lid with a smile for the Pen Type D (v1 and above as of 20241125)

https://than.gs/m/1207884

Happy lid for Pen Type D

PenD_v1_smile_lid.stl

Inspired by both the [Pen Type C by CW&T](cwandt.com/products/pen-type-c) and [a model inspired by the Pen Type C by Peterson Daughtry ](https://www.printables.com/model/806497-flat-pen-for-pilot-g2-cartridge)

I wanted to design a multi-pen that uses Euro Style cartridges, although this is not it yet, this will serve as a stop gap for me, so thought, lets share it. I think for myself as I just need black and orange inks, I will probably just keep a spare black ink in the 3rd slot. Sure, I could carry two pens or a pen and refills, but I just want to be able to switch inks without the colours or inks being shit or hard to find. D1 and the Japan style thin refills suck and no one wants to admit it, someone needs to make a chunky 3-in-1 multipen for G2/Euro Style refills sooner or later. 

The pen requires a 1/4" Socketed screw to keep the cartridge in place. If enough interest is there I'll model up a plug to use instead. An M7 screw would probably work too, although it'll be a bit tight. Print with tree supports as needed. 0.2 layer height or lower. 

I've also included a model for the clip I was working on for it, I don't really need a clip myself and its a bit flimsy, again with this if the interest is there I'll work on a better version of it. 

The Pen accepts 3 cartridges of the Euro Refill type, I want to make a variant that accepts Muji's Refills too. Included is a plain lid too. Some cartridges I've found can be loose, just give them a little washi tape to thicken them up a bit. 

The holes in sides are to get a grip on the stowed cartridges so that they can be quickly removed and swapped. 

The Smiley Lid from the video is available from here for members: https://than.gs/m/1209182

P.S: The refills in the photos are a Schneider Topliner Fineliner 970 0.4 in black, a Pilot G2 Orange gel and the "fill" of a Kokoyu Good Tools Orange Gel, (unfortunately they don't sell them out of the casing, unlike the other two).

P.P.S: Printed on a heavily modified Ender 3 at 0.2 layer height and a 0.4 nozzle, although I designed it originally with a 0.8 nozzle in mind I would recommend sticking with the 0.4 unless you're really good with the flow and overhangs, even with supports I was having some issues. Its all printed in Amazon Basics Neon Orange. 

P.P.P.S: It's named Pen Type D because I was prototyping in a light brown and it is very, uhh, phalic, with the lid. When I reprinted in orange it's much less apparent, I felt I do owe it to you dear reader that I admit this juvenile origin for the name, if I were to rename it later it's probably going to get a much longer and sillier name. 


Pen Type D - A 3-in-1 ish Pen that stores 3 Euro/G2 style refills

PenD_v1_Body.stl

For the organisation rituals I guess. Magnet holes in the base. I'll add photos eventually. 
The hole should be big enough to put in a M2/M2.5 heat press screw insert But I Didn't Test It. This is for the dipped incense type incense despite the cone. The holes at the bottom are to aide in cleaning if that's your Sort Of Thing. 

I want to expand this into something more modular for the other sorts of incense out there (Cones, Compacted Sticks). But its almost midnight and I Dont Want To right now. 

Gridfinity Incense Stand 

gridfinity_incense.stl

Just a quick model I whipped up to be able to press the buttons on the back, when in the included "case"

Heltec Wireless Paper buttons

wirelessPaperButtons.stl

Will probably change a bit later, I think it still needs a cover for the front and a better solution for the battery for accommodating bigger/different batteries

Has space for a 503562 lipoly, as thats what i have lying around. 

Print on its head, using tree supports or similar with the lowest support angle you can do with it just supporting the top (the bottom). The holes are filled but can be removed easily with snips, the switch one in particular you should remove. 

The images are a print that is in 3DTomorrow PLA, printed at 0.2 layers on a 0.4 nozzle on a Ender 3. 

LILYGO T-Desk Case 

tdeck-case.stl

I'm not sure how it happened, but this small part broke in one of my ear pieces. So I remodelled the remaining on from the other side and printed the part. Minimal cleanup was needed, printed in PLA and it is fine if a little stiff as the spring inside was deformed during the break. 

Uploading to save someone else the measuring and modelling time, no point us repeating each others work

AIAIAI TM-1/TM-2 Band holding nub

Placeholder plan. Both due to having only one upload and fees. Once there's more models I'll add the cheapest I can at the same level of access. 

Supportive

PenD_v1_Aesthetic_Clip.stl

PenD_v1_Plain_Lid.stl

gridfinity_wrist_mount_v1_18mm.stl

to make things that are functional but that function is sometimes unclear or quite niche really

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

revebla

Achievements

Seedling

Voyager

Pinned models

Gridfinity Incense Stand

Pen Type D - A 3-in-1 ish Pen that stores 3 Euro/G2 style refills

Gridfinity Wrist Baseplate 1x1

Gridfinity Compatible Nesting Bin 1x1x6

Anker 5-port Power Supply Bracket for Command Strips

Band/Edge Protection For Notebooks

Gridfinity Compatible Nesting Bin 1x1x6

Gridfinity Wrist Baseplate 1x1

Happy lid for Pen Type D

Pen Type D - A 3-in-1 ish Pen that stores 3 Euro/G2 style refills

Gridfinity Incense Stand

Heltec Wireless Paper buttons

LILYGO T-Desk Case

AIAIAI TM-1/TM-2 Band holding nub