Lids for gridfinity boxes so they are easier to transport without the content mixing or falling out.

I found my self often in the situation where I needed to take a few of my gridfinity screw boxes with me. I prefer that the screws stays in the boxes and do not mix or fall out. Apparantly there was no good models for this on thangs or anywhere else. So here is a collection of lids.

Features:
-Screws and other stuff stays in their compartments
-Use as little material as possible while doing it's job
-fits snuggly on top on boxes. (tolerances change depending on the printer)

I still recoment to use a rubberband or similar to hold the lid in place.

Gridfinity Lids

Gridfinity Lid 1x3.stl

Gridfinity bulk storage of drills from 1.5mm to 10mm in 0.5mm intervals. good for compact storage of all your spare drill bits.

Gridfinity Drill Caddy

Gridfinity 1.5 - 10mm Drill Caddy

This 2x2 unit “chain link” bin is compatible with the Gridfinity modular storage system designed by Zack Freedman: https://thangs.com/?category=Gridfinity#content . It is part of a set of four sizes with inside heights of approximately 20mm, 40mm, 60mm and 80mm

See here for video: https://youtu.be/ia-tEUhWVfw 

Links to full 2x2 set:
Chain Link Gridfinity Bin 2x2 20mm: https://social.thangs.com/m/714038 
Chain Link Gridfinity Bin 2x2 40mm: https://social.thangs.com/m/714060 
Chain Link Gridfinity Bin 2x2 60mm: https://social.thangs.com/m/714082 
Chain Link Gridfinity Bin 2x2 80mm: https://social.thangs.com/m/714105 


The boxes will fit on to the baseplates found here: https://social.thangs.com/m/60925 . 

Prints without supports. Holes to insert 6mm (1/4”) magnets on the bottom to use with magnetized Gridfinity baseplates.

See here for 1x2 unit bins:
Chain Link Gridfinity Bin 1x2 40mm: https://social.thangs.com/m/688026 
Chain Link Gridfinity Bin 1x2 60mm: https://social.thangs.com/m/688029 
Chain Link Gridfinity Bin 1x2 80mm: https://social.thangs.com/m/688031 
Chain Link Gridfinity Bin 1x2 100mm: https://social.thangs.com/m/688034

See here for single unit bins:
Chain Link Gridfinity Bin Single 40mm: https://social.thangs.com/m/664238 
Chain Link Gridfinity Bin Single 60mm: https://social.thangs.com/m/664257 
Chain Link Gridfinity Bin Single 80mm: https://social.thangs.com/m/664280 
Chain Link Gridfinity Bin Single 100mm: https://social.thangs.com/m/664302


Chain Link Gridfinity Bin 2x2 (20mm)

This 2x2 unit “chain link” bin is compatible with the Gridfinity modular storage system designed by Zack Freedman: https://thangs.com/?category=Gridfinity#content . It is part of a set of four sizes with inside heights of approximately 20mm, 40mm, 60mm and 80mm

See here for video: https://youtu.be/ia-tEUhWVfw 

See here for 3D files:
Chain Link Gridfinity Bin 2x2 20mm: 
Chain Link Gridfinity Bin 2x2 40mm: 
Chain Link Gridfinity Bin 2x2 60mm: 
Chain Link Gridfinity Bin 2x2 80mm: 

The boxes will fit on to the baseplates found here: https://social.thangs.com/m/60925 . 

Prints without supports. Holes to insert 6mm (1/4”) magnets on the bottom to use with magnetized Gridfinity baseplates.

See here for 1x2 unit bins:
Chain Link Gridfinity Bin 1x2 40mm: https://social.thangs.com/m/688026 
Chain Link Gridfinity Bin 1x2 60mm: https://social.thangs.com/m/688029 
Chain Link Gridfinity Bin 1x2 80mm: https://social.thangs.com/m/688031 
Chain Link Gridfinity Bin 1x2 100mm: https://social.thangs.com/m/688034

See here for single unit bins:
Chain Link Gridfinity Bin Single 40mm: https://social.thangs.com/m/664238 
Chain Link Gridfinity Bin Single 60mm: https://social.thangs.com/m/664257 
Chain Link Gridfinity Bin Single 80mm: https://social.thangs.com/m/664280 
Chain Link Gridfinity Bin Single 100mm: https://social.thangs.com/m/664302


1x1 Gridfinity block for storing up to 10 USB devices as well as 3 Micro SD cards. Simple design set up for fast printing. 

Recommended settings are as follows:

Layer Height: .32mm
Walls: 3
Infill: 10% - 20% (depending on desire)
Supports: No

Drives will sit straight up and down but are intentionally a tiny bit loose - in my experience if they are tight in the socket you end up picking up the whole block instead of the drive you want.

____________________________________________

Find all of my Gridfinity models here:

https://thangs.com/search/%22--thingymaker9000gridfinity--%22?scope=all

--thingymaker9000gridfinity--

____________________________________________

If you find these or anything else I make useful, you can buy me a beer over here:

https://www.buymeacoffee.com/thingymaker9000

Enjoy!

Gridfinity USB & Micro SD Holder

1x1 Gridfinity block for storing up to 10 USB devices as well as 3 Micro SD cards. Simple design set up for fast printing. 

Recommended settings are as follows:

Layer Height: .32mm
Walls: 3
Infill: 10% - 20% (depending on desire)
Supports: No

Just a funky holds-too-many-things for my Gridfinity desk. Holds a bunch of thumb drives, SD whatever cards, MicroSD whatever cards.... Yeah. It's awfully busy but that's half the fun.

Pixel Box Recommend Gridfinity Accessories

Models in this collection

Gridfinity Lids

Gridfinity Drill Caddy

Chain Link Gridfinity Bin 2x2 (20mm)

Gridfinity USB & Micro SD Holder

Gridfinity USB Thumb Drive SD MicroSD TF SDXC SDHC SDUC T-Flash TransFlash holder