Gridfinity Paint Brush Holder & Rinser - Wet / Dry

This is part of my Gridfinity Paint Stuff collection. I've been wanting some Gridfinity-based organization for my paint area, so I made some stuff.

This is a paint brush holder I made for when I'm actively working on something. It's angled so that you can sit the brushes in it and fill the small reservoir with water, letting you rinse your brushes as you go. It's not a lot of water, but enough to let you keep your brushes clean and maintained as you use them. You can also use it dry as a simple organizer for the brushes you're using on your current project. each one holds up to 5 brushes.

I have a holder for sponge brushes coming soon as well - keep an eye out if you use those.

Recommended print settings for all of my Gridfinity Paint Stuff are as follows:

Supports: None
Infill: 8% - 12% lines or tri-hex
Line Height: .2 - .24

If you find these or anything else I make useful, please consider buying me a beer:

https://www.buymeacoffee.com/thingymaker9000

Enjoy!

Gridfinity Sand Block Holder

This is part of my Gridfinity Paint Stuff collection. I've been wanting some Gridfinity-based organization for my paint area, so I made some stuff.

This is a really simple holder for a pair of standard 3" x 4" sand blocks. Great for keeping them close by when you're working on large prints which require a lot of sanding to finish. I will probably add more sizes for this in the future.

Recommended print settings for all of my Gridfinity Paint Stuff are as follows:

Supports: None
Infill: 8% - 12% lines or tri-hex
Line Height: .2 - .24

If you find these or anything else I make useful, please consider buying me a beer:

https://www.buymeacoffee.com/thingymaker9000

Enjoy!

Gridfinity Spray Paint Holder

This is part of my Gridfinity Paint Stuff collection. I've been wanting some Gridfinity-based organization for my paint area, so I made some stuff.

This is a really simple holder for a standard sized can of spray paint. Perfect for when you need a few rattle cans on hand quickly, but they also work great for storing and organizing a large quantity of cans on a shelf.

Recommended print settings for all of my Gridfinity Paint Stuff are as follows:

Supports: None
Infill: 8% - 12% lines or tri-hex
Line Height: .2 - .24

If you find these or anything else I make useful, please consider buying me a beer:

https://www.buymeacoffee.com/thingymaker9000

Enjoy!

Gridfinity Paint Palette

GPS-4x1-Paint-Palette.stl

Gridfinity Acrylic Paint Bottle Holder

GPS-4x1-Paint-Holder.stl

Steel Series Arctis 1 Wireless Accessory Case

Steelseries Arctis 1 Accessory Case.stl

Gridfinity 1x1 Glasses Holder - No Supports

Here is a basic, 1x1 Gridfinity glasses holder. Holds sunglasses as well as eyeglasses up to 145mm in width. However the file can easily be modified to increase or decrease height as needed.

Use the following print settings and you should have no issues as well as an under 2 hour print:

Layer height: .24 - .32
Walls / Top / Bottom: 3
Infill: 10% - 20%
Supports: none

View all of my Gridfinity models here:

https://thangs.com/search/gridfinity%2520%252B%2520%2522thingymaker9000%2522?manualModelView=true&scope=all

Gridfinity Dry Docks for Storage Drives / Hard Drives - 2.5" | 3.5" | M.2 | SSD

Gridfinity Dry Dock for Storage Drives - SSD Size Drive.stl

Shower Caddy | Soap Holder | Single & Double Sizes

Shower Caddy Single.stl

Gridfinity 2x3 Altoids Tin Adapter

Gridfinity Altoids Tin Adapter.stl

Gridfinity 1x1 Dense 9 Full SD & 9 Micro SD Card Storage

This is a 1x1 block for the Gridfinity system, which stores up to 9 full-size SD cards as well as 9 Micro SD cards.

I recommend printing this if you have a large amount of SD cards to store. This is not great for cards which you are using constantly, as it will get tedious to remove individual cards. This is dense storage for those of us who have lots of these cards and adapters lying around.

Print settings are as usual for my Gridfinity items:

Layer height: .24 - .32
Top / Bottom Layers + Walls: 3 - 4
Infill: 10% - 20%

Use the lower values for cheaper / faster prints; use the higher values for weightier / higher quality items. You get the idea.

Gridfinity Dense 1x1 Full SD & Micro SD Storage

Gridfinity 2x1 Phone Stand - No Supports Needed

This is a no-frills, no-nonsense phone stand for the Gridfinity system. It does not require supports. It will probably fit your phone - it fits a OnePlus 7 Pro just fine. There is a slot for a charger on both sides, if you're into that sort of thing.

It's not too pretty but it will make your phone stand up, and it fits with #Gridfinity so print one out if you want. I recommend these settings:

Layer height: .24 - .32
Infill: 10% - 20%
Walls: 3
Top / Bottom layers: 3

Gridfinity Phone Stand - No Supports Needed

Gridfinity USB & Micro SD Holder

1x1 Gridfinity block for storing up to 10 USB devices as well as 3 Micro SD cards. Simple design set up for fast printing. 

Recommended settings are as follows:

Layer Height: .32mm
Walls: 3
Infill: 10% - 20% (depending on desire)
Supports: No

Amazing Spider-Man Wall Art - Easy Filament Swap

A super easy filament swap print for those who want to try it out. This print can be used as a cool bit of wall art as I show in the picture, simply put it in a frame and add some color-changing LEDs behind it and this print really pops.

Here are my print settings:

Layer height: .32mm
Walls: 3
Top & Bottom: 6 layers
Infill: 8% tri-hex pattern (no actual infill will print, it will be all top / bottom layers)
Material: PLA+, 208F hotend, 60F bed
Support: None

I used white PLA+ for the bottom and black PLA+ for the graphic. Use whatever material you like, but I highly recommend they are the same type and brand, just different colors. This eliminates a lot of variables and makes sure they bond together as best as possible.

In Cura, insert a Filament Change at Layer 4. You should have 3 layers of background material, then the rest will be the graphic, so you will need to change prior to layer 4 starting if you decide to pause and do it manually. I recommend having your nozzle move up and away so that you can push some extra filament through. This prevents smears of the previous color ending up in your graphic.

PS: For the frame, I simply cut out some black construction paper to fit a 9" x 9" shadow box, and then cut a rectangle out slightly smaller than the print itself and mounted the print inside of it. Then I just ran a cheap RGB LED strip around the back. Cool effect for cheap :)

PPS: I obviously don't own the art copyright itself, I used publicly available images and fonts for this private work of fan-art.

Spider-Man Wall Art.stl

100Hex Hellraiser Box Lament Configuration Tiles

Hellraiser 100 Hex Face 1a.stl

Small Table Base

This is the base for a small table. The legs will stand approximately 6in off the ground, plus the height of whatever table top you use. Perfect for low-seated areas where you need a small table.

Prints in one piece, no supports. Includes holes to screw in a table top. I recommend the following settings:

15 - 20% infill
3 - 4 walls / perimeter shells
3 - 4 top & bottom shells

The more infill / shells you do, the better it will turn out. It will also use more filament, so you can choose your preferred settings. It will take between 10 and 15 hours to print.

Please note that this table is in no way meant to be load-bearing. This should go without saying but it's not a seat in any way, this is a base for a small table and has a load capacity of 5 - 10lbs. You're responsible for how you use it.


A Round To It

Round_To_It_serif.stl

Ubiquiti Nanobeam M5 external mount replacement

This design conforms to the mount pole which originally came with the device. Use if you're attaching this mount to stock hardware or something similar.

mount-arm-with-pole-gap.stl

Febreeze (or other) Air Freshener Wall Mount or Holder

Made this so we can have quick access to air freshener around the house. Never know when you might need it!

These are mounted with strong double-sided tape, but you could easily modify this to have screw holes through the mount plate if desired.

I print these at 15% infill (mostly only matters for the bottom) using PLA or PLA+. Should print in about 2 1/2 hours.

I make stuff, mainly when I need something specific I can't find anywhere. Not the best, not the worst. Maybe something I've made will work for something you need.

thingymaker9000

Achievements

Seedling

Fan Favorite

Novice Maker

Trailblazer