tracking pixel
3D Printing World

Collapsing Master Sword (Print-in-place)

by
3dprintingworld
Follow
Follow
Remix Model
3dprintingworld
3dprintingworld
|
Image 1 of 15
Collapsing Master Sword (Print-in-place) 3d model
3dprintingworld
3dprintingworld
|
Image 1 of 15
Collapsing Master Sword (Print-in-place) 3d model
2D
3D
Makes
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) - 4 color PIP using X1C. - 3d model
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) - I was super thrilled with this print! - 3d model
Collapsing Master Sword (Print-in-place) - Amazing! Tolerance on the blade is a little tight but I bet that loosens up over time  - 3d model
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) - came out nicely - 3d model
Collapsing Master Sword (Print-in-place) - Rainbow silk! Wasn't sure if it was gonna look good, but I love it! - 3d model
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) - As far as the blades will push down. Unable to pull apart. Were printed separately. - 3d model
Collapsing Master Sword (Print-in-place) 3d model
Collapsing Master Sword (Print-in-place) - printed on Anycubic Kobra 3 Combo (i clicked Bambu Lab A1 because thats the closest thing to Kobra 3 and they dont have Kobra 3 as an option) using Pantone Tropical Turquoise, takes a lot of force to get back in, extends to only 650mm, great quality, the little thin ceiling in the pommel where the blade ends broke when forcing the blade back in so the blade goes in a little further than normal, otherwise printed okay - 3d model
Collapsing Master Sword (Print-in-place) 3d model
This model is restricted by licensing terms. 
1.2K Likes12K DownloadsNovember 6, 2021
This model is restricted by licensing terms. 


Collapsing Master Sword This Master Sword prints-n-place as just the hilt but extends in to a full sword. Its 250mm tall when printing but extends to 870mm long! The sword is designed to be printed with a .4mm nozzle so the blade is two shells thick. The line width should be set to .42mm.

Master Sword Versions Replaceable Blade Dual Extrusion Three Color

Scale If you must scale only scale Z or change your nozzle size to match a smaller scale nozzle. For example, you can use a .3 nozzle and scale it to 75%, .32mm line width. This would make it roughly 190mm tall.

Print Settings I had issues printing this the first time, I would suggest everyone do print the test print which can be found here I printed several of them to better tune the retraction at layer changes. My issue was the size of the layer seams were causing the blades to fuse. The test print is a total of 24mm high so I change retraction setting every 8mm. Then I compare the changes until I achieve the best result. Each printer is going to be different but in my case I used a negative “extra restart” distance to reduce the size of the layer seam.

Detailed printing instructions can be found on my website

Printed with 3D Fuel Cobalt Blue and Silver Pro PLA

Printed on the Muldex rep-rap IDEX printer.


Support and Licensing If you would like to help support more free models please consider joining my Thangs Membership To get permission to sell physical copies of my models, consider joining my Patreon


1.2K Likes12K DownloadsNovember 6, 2021




This model is restricted by licensing terms. 
1.2K Likes12K DownloadsNovember 6, 2021
This model is restricted by licensing terms.