B6 Hood Release Latch

Ingenious Jarv.stl

GoPro Mount for a headrest, can be inserted on headrest and pinched between seat and headrest.

GoPro Headrest Mount

Frantic Jaagub-Bojo.stl

Mac 3Port Mount

Daring Gogo.stl

EK 96-98 lower console air ride and usb mount 

EK AirRide Console Mount

Air_ride_centerconsole_EK.stl

Ecu mount for a 0BD1 ecu in EK chassis mounted in the center of the foot well. Uses a factory bolt hole. Fits under carpet and used on my custom tucked harness that enters in the center of the firewall.

EK ECU Firewall Mount

EK_0BD1_ECU_Firewall_mount.stl

A full Bezel and pod kit for the Flock Multigauge BETA version! Gives a nice professional look with a glass lens and low profile bezel. 

Flock Gauge v1 

Pod.stl

Simple, yet functional rd1 cupholder. Added a option for JUUL holder version for us vapers.

NOT FOR RESALE.

 

RD1 CRV Cupholder v1

Simple, yet functional rd1 cupholder. This model is still in test form, print and comment with issues or improvement. 

NOT FOR RESALE.

 

rd1_cupholder.stl

This is a spacer needed to run the clutch master from a s2000 on a ek civic. Very common upgrade for a cleaner bay. MUST print 100% infill so it don't flex.

S2000 Clutch Master Adapter for EK Civic

Not perfect but replaces the metal mount that rust out. most likely fits 92-00 civic and so on.

96-00 Civic Clutch Reservoir Mount

Factory sized fuel rail spacer. they are tiny and can get lost while doing a rebuild, or end up like me and drop them and never find them again. 

Honda B-D Fuel Rail Spacer

Perfect fit 70mm Throttle body gasket for honda/acura. I printed in TPU and it works amazing. reusable unlike oem paper gaskets.

Honda 70mm throttle gasket

These are plugs to cover all the holes in the engine bay on a 96-00 civic when doing a shaved bay / wiretuck. they may fit later older models as well. they look factory and click tightly into place. save yourself $100+ on the oem plugs. Printed in PETG, asa. or abs.

96-00 Civic Firewall Plugs (wiretuck)

drivers plug.stl

Wireharness_Plug.stl

replaces the radio with dual gauge pod, only works with aftermarket radio din/cubby. added a revised version for easier printing, print clips separate, glue onto back side. Also added a tipple pod.

99-00 Civic Single Din Radio Gauge Pod

replaces the radio with dual gauge pod, only works with aftermarket radio din/cubby. 

gauge_pod_clip.stl

triplepod.stl

just a simple spacer that allows you to use the outer upper timing cover on a honda b series without the inner cover that goes behind the cams. the inner cover is known for warping so this allows you to still us the upper cover without it.

B Series Upper Timing Cover Spacer

Quick gauge pod I designed to fit in the place above the cup holders on a 96-98 civic. I did have to sand my gauge down a little because there isn't any way possible to make the hole bigger! will be updating at some point when i figure out a better approach.

96-98 Civic Gauge pod

Made this gasket and plate to block off the high idle thermal valve on a b/d series honda throttle body. based off scans of original gasket, printed in high temp petg and wokred flawless for me.

Honda HITV Block off

Replaces the gasket between the throttle body and intake manifold with the hitv port fully blocked off.

bseriesgasket.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

mackbanville

Achievements

Seedling

Explorer

Up and Coming