_"Six bullets. More than enough to kill anything that moves."_ - Revolver Ocelot

Five shots will have to do! Take this six-shooter for a whirl if you are looking for a different take on the existing Revolver Tile. Like the original, the whole tile is a trigger zone. When a ball rolls through it, turn the cylinder to release one ball from a chamber. All orientations are legal, so when placing choose carefully where to 'aim' the chute path. If a ball somehow ends up in a chamber, consider it a tacticool reload!   

**Rules Card Text**
Setup: Line up a chamber with the chute. Load balls into remaining chambers. Balls in chambers do not count for the 3-ball rule.
Trigger: Turn cylinder any direction to release one ball.

**Hardware**
One 10mm M3 screw. You may be able to get away with longer, but 10mm suffices. I recommend an M3 flat washer.

**Printing / Assembly Instructions**
Everything is printed in PLA. I printed the mount plate face down (so pins face up) with supports, which filled in the track where the balls sit. Other models do not need support and are self-explanatory.

Six Shooter Tile
1. Install the M3 screw through the top of the spinner, through the recommended washer if used, into the mount plate. Make sure its tight so that it doesn't rotate freely, but you can turn it.
2. Apply glue to the mounting pins and contact faces. Line it up, slot the plate into the tile base, and give it time to dry.

Rules Card
- Multi-material: drag six_shooter_card_base.stl and six_shooter_card_details.stl into your slicer simultaneously, loading it as one object with multiple parts. Assign filaments as desired.
- Single-material: print the single color model, or if you want multi-color add a pause and perform a filament swap.



Hextraction Six Shooter Tile

six_shooter.3mf

six_shooter_base.stl

six_shooter_cylinder.stl

six_shooter_demo_DO_NOT_PRINT.stl

six_shooter_mount_plate.stl

six_shooter_card_base.stl

six_shooter_card_details.stl

six_shooter_card_single.stl

It's a hit! Send ships and tiles to the bottom of the sea with this new tile for Hextraction.

Place ships on the tile face during setup. When a ball rolls through this tile, place a peg in a ship. Once that ship is full of pegs, it's sunk! Remove it and destroy _every tile_ in the corresponding slots on the board. This tile cannot be destroyed by it's own effect. Once all ships are gone, destroy this tile and put everything neatly away - you'll thank me later!

The tile face respresents a standard hextraction board. If your board has one more row, I've supplied the Extended Lid. If you have non-standard board shapes/sizes, interpret the grid positioning as you'd like! 

**Rules Card Text**
Setup: Place 1-3 ships on the tile.
Trigger: Place a peg in a ship. If that sinks the ship, destroy all non-Battleship tiles in the matching slots on the board. Destroy this tile when all ships are sunk.

**Printing / Assembly Instructions**
Everything is printed in PLA. The tile base and lid are two pieces, lid should be printed face-down, same for the pegs and ships. I needed a brim on the pegs and ships.Assembly is simply click-fit the lid to the base. Feel free to mix up your ship sizes/quantity, but the default is 1 each of the 2, 3 and 4 length (and the correct quantity of pegs per hole). Tolerance is a bit tight to keep things from falling out during play. I can supply tolerance modifications if requested. To produce my standard tile configuration, print:
- 1x battleship_tile_base
- 1x battleship_standard_lid **OR** 1x battleship_extended_lid
- 1x battleship_boat_2L
- 1x battleship_boat_3L
- 1x battleship_boat_4L
- 9x battleship_peg

Rules Card
- Multi-material: drag both the base and detail STLs into your slicer simultaneously, loading it as one object with multiple parts. Assign filaments as desired.
- Single-material: print the single color model, or if you want multi-color add a pause and perform a filament swap.

Coming up with a workable ruleset was a challenge for this tile. The biggest baked-in issue is that if your board is non-standard, you'll have to get creative with mapping the tile face grid to the real board. A different tile I have in the works will work with relative positions. Let me know your feedback! Big thanks to [NoStepOnDeez](https://thangs.com/designer/NoStepOnDeez) for workshopping the rules with me, and for the inspiration for the tile container design (linked as a remix parent).

Enjoy!


Hextraction Battleship Tile

battleship_extended_lid.stl

battleship_standard_lid.stl

battleship_tile_base.stl

battleship_tile_extended.3mf

battleship_tile_standard.3mf

battleship_boat_2L.stl

battleship_boat_3L.stl

battleship_boat_4L.stl

battleship_peg.stl

battleship_card_base.stl

battleship_card_details.stl

battleship_card_solid.stl

Ragnarök begins when Jörmungandr the World Serpent makes it to the board.
Introducing the first _customizable-triple-folding-combo-forbidden-effect-tile_ for Hextraction! Let's get into it.

This tile is a triple folding combo: each tile is connected via links and magnets keep it closed when not in use. Simply unfold, tuck the long link into the middle, and place it on the board if space is available. 

Its customizable: the tail can be swapped out for any standard double lane tile (e.g. original [double lanes](https://thangs.com/designer/NoStepOnDeez/3d-model/Hextraction%20Double%20Lane%20Tiles-1061128) or my [Riptide exit](https://thangs.com/designer/cadeluca/3d-model/Hextraction%20Riptide%20Tile-1130359?source=mymodels)). The head and middle cannot be swapped, else the assembly couldn't deploy or fold properly.

The forbidden effect: Honestly, I suggest voting the effect off and enjoying the novelty of the tile itself, but it's there if you want it! Overdrive without a full board is the diastrous reality of Ragnarök, and is thus Forbidden. If you are a fan of Norse mythos **_and_** have a ton of Hammer tiles, you are in luck.

**Rules Card Text**
Forbidden - Ongoing: Overdrive is active while this tile is on the board. This tile can only be destroyed by a Hammer tile.

**Assembly Instructions**
1. Print the 3 body tiles, 1 standard link, and 1 long link. 
2. Match the shorter link slots up on the Tail and Middle. Put the standard link in place and jam snippets of filament through the hinge axis, then cut the filament flush.
3. Match the Head to the Middle's longer link slot. Put the long link in place, repeat the filament hinge install step.
4. Test that balls can roll through and that the combo folds properly. When folding, the bottom of Head and Middle should contact, and the top of Middle and Tail should contact.
5. (Optional) Glue 4 6x2mm magnets in place (Head: 1 on bottom; Middle: 1 on top and bottom; Tail: 1 on top).

Hextraction World Serpent Tile

Link.stl

Long_Link.stl

World_Serpent_Card.stl

World_Serpent_Card_Base.stl

World_Serpent_Card_Details.stl

World_Serpent_Head.stl

World_Serpent_Middle.stl

World_Serpent_Tail.stl

_“Push your enemies away or pull them toward you - with UNDERTOW, you control where the fight occurs.”_ - Fink Manufacturing

I've designed a series of tiles representing Vigors from BioShock Infinite - tonics the player consumes to gain a myriad of powers. Each tile is designed to look like the unique Vigor bottles, with their powers captured as game effects.

**Rules Card Text**
On Play: Push or Pull a tile in line of sigh with one of Undertow's edges. Push: Move the target tile away from Undertow until it is blocked by another tile or the edge of the board. Pull: move the target tile next to Undertow.

**Printing / Assembly Instructions - _Please Read Before Printing_**
I've provided various options to help those who don't have multi material systems, or to minimize filament waste if you do. I also included 3mf files.

Undertow Tile
- MMS: Drag undertow_tile_base and undertow_tile_octo_surface into your slicer together. Assign colors and print.
- No-MMS: Same as above, but pause and swap filaments for the surface details.

Undertow Icon (Print twice if using it in the card - see the card section)
- MMS: Drag undertow_icon_base, undertow_icon_foreground, undertow_icon_octopus into your slicer together. Assign colors and print.
  -  If you want to minimize filament swaps, print the foreground separately and glue it on.
- No-MMS: Drag undertow_icon_base and undertow_icon_top into your slicer together. Pause and swap filaments for the top section. 
  - You may also choose to print the icon as a single unit (undertow_icon_single). 
  - If you want as close to the 3 color variant as possible, you could print the base and octopus with a swap, then print the foreground separately and glue it on.

Glue the Undertow Icon onto the tile.

Undertow Card
I've designed this to use the same icon as the tile, but you can absolutely forgo that extra work and just slice the solid stl as you please (undertow_card_full). Otherwise, print a second Icon to use with the card and continue:
- MMS: Drag undertow_card_base and undertow_card_detail into your slicer together. Assign colors and print.
- No-MMS: Same as above, but pause and swap filaments for the surface details.
  - Or use the undertow_card_no_icon_one_piece stl and slice as you please.

Glue the Undertow Icon onto the card.


cadeluca

Achievements

Voyager

Seedling

Debutant