A very simple velcro-down divider to keep stuff from sliding around in my trunk

Trunk divider

This is a simple adapter to capture the handlebar mount, and attach it to something flat.  My intended use case is a Scosche magnetic mount; I'll stick a metal plate to the back of this and it will go on the existing magnetic mounts.  But this could also work with any stick-on / VHB tape.

This part has some clearance built in and doesn't require a tight fit.  I printed in a _fancy_ TPU but any sun- and heat-friendly material should be fine.

Use one of the included bands to secure the mount.  Both would certainly be overkill.

The model does not require any supports or rafting; should be a very forgiving print.

Beeline flat adapter

This is a simple adapter to capture the handlebar mount, and attach it to something flat.  My intended use case is a Scosche magnetic mount; I'll stick a metal plate to the back of this and it will go on the existing magnetic mounts.  But this could also work with any stick-on / VHB tape.

This part has some clearance built in and doesn't require a tight fit.  I printed in a _fancy_ TPU but any sun- and heat-friendly material should be fine.

A blank for a round shift knob.  It's sized for a Caterham or Miata (same transmission).  Will need to be tapped with an appropriate $4 tap from your favorite retailer; some MX-5 use 10x1.25, my 7 uses 10x1.5.

Two parts, they print with no supports and will snug together when installed to keep it from rotating.  For best feel, chuck it (while tapping) and spin the parts in sand paper.

Designed to be leather-wrapped, but the (sanded) plastic feels good too.

Note that the shifter can get pretty hot in warm weather, so print in TPU, PETG, PC, PA, or something tolerant of heat.

Round shift knob

leather ball 2-pt - ball.stl

an old cafe-style straw holder.  Uses 1/4" dowel for the connection from lid to base.  insert the 'base' into the cup, dump a bunch of straws on it, then put the lid down.

Sized specifically for 7.8" disposable straws

Straw Holder jar

straw holder - cup.stl

A remixed set of files from a T-Rex model; sized for a 16" tree, with laser-cut "hips" for support.  If the tree is not pre-lit, add lights :)

Tree Rex

TRexHeadSupported smol.stl

laygs, smol - hip (v).stl

laygs, smol - hip (h).stl

filament spools are floppy and annoying and slow to print; this is one made from laser-cut wood.  it's 3 pieces to minimize wood consumption.  Can be made with 2, 3, 4, or 6 petals; the 3- and 6-petal versions probably make most sense.

Print 2 hubs, 2/3/4 or 6 spindles, and twice that many petals.  So a "3 petal" version as pictured has 2 hubs, 3 spindles, 6 petals.

Laser Spool for Filament

laser spool - hub.stl

a dead-simple Switch stand.  It unsnaps to store flat, but when open is very stable.  Room to cut in a triforce or bellbag or whatever.

Laser-cut Nintendo Switch stand

laserstand - lhs.stl

Models for a laser-cut wood box, or a printed box + lid, sized to fit a wowstick and accoutrements

The model is symmetric: print two fronts and two rights, to make all 4 sides.

Wowstick case

wowstick case - base model

tyre block for 185/55/R13; meant to be mounted on top of wood blocks for height.  basically a 2-sided chock

tyre block - Part 1.stl

This is an insert to go inside the barrel of an inexpensive HF rock tumbler.  Use a bunch of these to keep media or stages separate.

Tumbler cup wik lid

cup - cup.stl

cup w- agitators - cup.stl

A small, printable hook to tuck under the console without requiring any destructive fasteners.  Used to secure the corners of a small cargo net.

net hook

A spanner specifically for the Bilstein rings

C-Spanner

This is a simple cover for the bare wiper spindles on a Caterham with aeroscreen fitted.  Will probably fit any model.  Print in a sunlight-tolerant material like PETG, PC, ASA...

7 wiper spindle cover

This is a simple cover for the bare wiper spindles on a Caterham.  Will probably fit any model.  Print in a sunlight-tolerant material like PETG, PC, ASA...

A simple holder for 22x 18650 cells.  First draft, but it works exactly like what I wanted.  The cells are isolated, prints w/o support, very simple.  Perfect for hurricane season when you're deboning old hoverboard packs.

18650 holder

A printable template to make a small changepurse, the "octobag."  Designed to be easy to cut, all straight lines and convex corners.  Holes are spaced 5mm for ease of pricking.  The larger holes are meant to be about 4mm (paracord) but knock yourself out.

Included DXFs to etch (or cut) your leather directly :D

Octobag leather template

octobag 6 tall - side.stl

Updated octobag 6 tall - side.stl, octobag 6 tall - base.stl, octobag_6_tall_-_base.stl

octobag 6 tall - base.stl

A loop of paracord (or similar) and this attaches to the headrest of your car seats.  It can help secure a purse or grocery bag to keep them from floppin around while you're driving safely and carefully.

Printed in the natural orientation without support. 

Seatback bag anchor

A water-retaining planter designed to hang (from like a tree).  Thepot is 6" at the top, about 5" deep, and will retain 2" of water to the (hidden) drain.

Ideal for Nepenthes / hanging pitcher plants, helping them tolerate ~weekly watering or rainings.

Printable without supports, max 45* overhang.  Designed for a simple / attractive color change at the top.

Skeeter-free hanging nep planter

a 2-part / multi-friendly pot for Carnivorous Plants, sized to fit on a ~6" ledge.

6x4 Carnivorous Plant pot

6-in ledge planter, multi - pot.stl

a Carnivorous Plant-friendly pot in 2 parts: a saucer, and independent pot w/ drain / wicking holes.  Print in multiple colors (if you wish).  The pot is THICK and may provide some insulation to protect your plants from temperature shock.

Print the two separately.  The parts can be used independently, but I like to seal the saucer with rubber paint, and (while drying) place the pot there to sort of glue it down.  For outdoor use I prefer PETG.

2-color Carnivorous Plant pot

2-color 6in planter - pot.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4993771.

I made some "simple" stacking bins for my wife's sewing things (like little clips and pins and whatnot).  Very clean design, easy to print, easy to use.  Includes two sizes -- one about 4" on a side, and a 1/2-size version so 2 small ones can stack on the larger.

I made a more sophisticated (and boxier) part for my own garage use.  This design is modular, I can blow them up pretty large.  Smaller generations will stack 2-per-layer on the next larger size.  Each size includes a matching "lid" if needed, though realistically I'll probably only use the lid for the smaller sizes.

I've only made 1 depth (about 2cm + the ledge) but can fire up deeper models if anyone needs.

Stacking bins

modular_stacker_g3_-_bin.stl

modular_stacker_g3_2x_deep_-_bin_(1).stl

modular_stacker_g2_5cm_deep_-_bin_(1).stl

This is part of a set of modular templates which could be used to make a thing.  Print them in PETG and use to cut and punch individual pieces. 

These aren't meant to assemble anything specific, but should be the interesting parts (like corners or interfaces) to make, like, a bag.

This specific part is an "outside corner".  The seam and raw edge is visible in the finished product.

It could be used to make a reinforcing corner, but is really meant to be incorporated into a larger design.

Modular leather template: outside corner

A simple template to cut an outside corner for like... a bag.  5mm seam, 5mm hole pitch, and assumes ~ 2mm leather thickness (4-6 oz range).  This shape can be subbed in the corner of a much larger piece, or used as-is to just create a reinforcement corner for a bag.

Leather template: outside corner, 2mm

NEW AND IMPROVED!  A useless set of marks to show where the material will be folded

outside_corner_v3.stl

A simple cover for Gardyn ports, to prevent algae growth.  

The solid cap just blocks unused ports.  Print in PETG or TPU, it should be snug but not "tight".


Gardyn covers

A simple cover for Gardyn ports, to prevent algae growth.  

The foil cover is meant to hold down a piece of aluminium foil.  Place a square of foil over the port and use the cover to hold it down.  Poke a small hole in the middle for your seedling.  as it grows, the seedling may widen the hole itself.  Or you can help it, whatever.  

When you're ready, tear the foil and slide the cover out of the way, without damaging the seedling.

rigid_foil_cover_(1).stl

rigid foil cover (1).stl

I design simple, easy-to-print, functional items for around the house.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

austindavid