Made for the ACC Premier buttstock 
uses two standard M-LOK screws and nuts to be attached 

If you prefer to buy the product complete. visit our store at www.hitthat.ca and view and buy any of our innovative products.

M-Lok Bag Rider 

Large Bag Rider.step

This kit contains three files.
1) Bolt shroud insert ( fits between the bolt handle and chassis to close the hole)
2) MagLatch Release for easier location of mag latch, helps if you have limited mobility in hands 
3) Under barrel tailer insert to fit better for sporting contours 

make sure you download all three separately 

use ASA for best durability 

MDT- Field Stock dressing kit

R700 SA- Bergara Bolt shroud insert.step

Not much to it, Bore Guide for cleaning and bore scope made for left and right handed bergara B14R actions ( the extractor moves )

Print from any material 

If you prefer to buy the product complete. visit our store at www.hitthat.ca and view and buy any of our innovative products.

Bergara B14R Barrel/Bore Guide.step

Bergara B14R Barrel Guide.step

PRIVATE USE ONLY. CONTACT FOR COMMERCIAL USE

So Here is the ACC_PREMIER internal weight and barrel bridge. 
NOTE: This is a 4 part file. make sure you download all four parts and print as many bridge section to need to accommodate your scope. 

This is for R700 inlets and should work on other models but may need some mods

The two inserts will replace your internal weights but you can add the weight back in the form or birdshot inside the insert. ( up to 2lb) 

This will accommodate a 32mm barrel 

once the two inserts are glued and screwed in( mounted from the bottom into M3 or M4 inserts ) you can fill the insert from the front and cap it with the new nose cap. 
The side and bottom MLOK at still fully usable for additional weight or accessories.  

You will need M3x3.5 or 4mm heat inserts at least x50 and x50 M3 by 8mm hex key screws
ASA for best durability, print both inserts vertical for best strength and quality 

These are both accent and functional prints. if you print the inserts in a accent color and the caps are the same color as your frame, your M lok slots will be contrasted 

ACC_PREMIER_ Barrel_Bridge 

ACC_PRIEMER_INSERT_2.step

Simple, straight forward arca slide table stand for both R700 chassis and CZ457 inlet chassis, these are not the same!

these slide onto arca and same height as handle great for cleaning work 

TableStand for MDT Chassis.step

104820 ACC Premier - Part 34 (1).step

Finally a use for the open MLOK screw slots next to on the ACC chassis. These work great with the standard MDT chamber flag.  

Uses 10-24 x 1/4 counter sunk screws 

Best printed in PLA, NYLON, ASA - NOT ABS

FLAG-IT Chamber flag holder

Flag-IT Chamber flag holder.step

Here is a left and right handed MLOK thumb rest for ACC chassis, uses a single M-Lok nut and screw  

These have been tested on MDT chassis but should work on any MLOK compatible forward grip. 

Best printed in ASA or CF-Nylon. 

I added them to both sides of the chassis for the odd time we shoot off side/hand 

If you prefer to buy this product pre made, you can find a link to webstore here 
https://www.hitthat.ca/product-page/thumb-restkit 

MLOK- Forward Thumb Rest 

Right Thumb Rest.step

For many this is the missing piece to finish off the rifle. This one was made for R700 footprint and should work for most R700 footprint actions. 
ASA material in 0.12mm layers printed face down for best results. 

Other actions may need to file down the part a bit but I'm also willing to help make changes for more inlets

MDT ACC chassis Remington R700 Short Action Bolt insert 

ACC R700-Wide.step

Thumb Rest ( for right and left( wrong handed)) Shooters, these work great on ACC Gen 1 and ACC Gen2. 

Best printed in ASA and attached with 3M ultra thin double sided tape, but silicon or epoxy would work as well. just wont be removable. 

MDT ACC Chassis Rear Thumb Rest

Left_Rear_ThumbRest.step

Jay's Custom is a place to see and share 2A content that does not break the law but is helpful for most competitors

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Jay's_Customs

Achievements

Seedling

Debutant