4 Color HueForge model. Han Solo Carbonite filament painting made using Sunlu PLA+ colours.

Print at 0.08mm layer heights, 0.16mm first layer.  100% infill (Rectilinear)


 

Filaments Used:
Sunlu PLA+ Black Transmission Distance: 0.6
Sunlu PLA+ Grey Transmission Distance: 2
Sunlu PLA+ Silver Transmission Distance: 2
Sunlu PLA+ White Transmission Distance: 6

Swap Instructions:
Black until layer #6 at 0.56mms
Grey until layer #9 at 0.8mms
Silver until layer #11 at 0.96mms
White for the rest

 

This is a filament blending model, avoid special filaments and stick with the plain ones for the best results.  SUNLU filaments tend to be more transmissive and are a good choice.

Use the exact numbers in your slicer to match up properly.

two different size models are supplied and designed to print with 0.4 nozzle, 

**If re-scaling model make sure not to alter the Z height of the model**


ALL Ian Smalley's designs are protected by Copyright Law. Downloading does not give you permission to use the files or physical prints for financial gain. If you want a commercial license to Legally sell prints from my designs, you will need a SELLER subscription.

Han Solo Carbonite (Filament Painting)

han solo carbonite_Front_80x200.stl

6 Color HueForge model. 'Rocket Clock' filament painting made using Bambu Pla Matte filaments.


Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

Filaments Used:
PLA Bambu PLA Matte Charcoal Transmission Distance: 0.6
PLA Bambu PLA Matte Scarlet Red Transmission Distance: 2
PLA Bambu PLA Matte Mandarin Orange Transmission Distance: 3
PLA Bambu PLA Matte Lemon Yellow Transmission Distance: 4
PLA Bambu PLA Matte Marine Blue Transmission Distance: 2
PLA Bambu PLA Matte Ivory White Transmission Distance: 4

Swap Instructions:
Start with Charcoal
At layer #6 (0.56mm) swap to Scarlet Red
At layer #11 (0.96mm) swap to Mandarin Orange
At layer #12 (1.04mm) swap to Lemon Yellow
At layer #14 (1.2mm) swap to Marine Blue
At layer #15 (1.28mm) swap to Ivory White for the rest.

 

This is a filament blending model, I would recommend trying to match the td as close as possible if not using the exact filaments to get the best results

Use the exact numbers in your slicer to match up properly.

The Model is designed to print with 0.4 nozzle.

**If re-scaling model make sure not to alter the Z height of the model**

 

Mark the Centre at the rear and drill the required size hole for your clock movement.

Link for the movement that I used is listed below but any standard movement will be fine (be sure to check the size of the hands)

https://www.amazon.co.uk/dp/B0BBLXG55S?psc=1&ref=ppx_yo2ov_dt_b_product_details

ALL Ian Smalley's designs are protected by Copyright Law. Downloading does not give you permission to use the files or physical prints for financial gain. If you want a commercial license to Legally sell prints from my designs, you will need a SELLER subscription.

Rocket Clock (Filament Painting)

6 Color HueForge model. 'Rocket Clock' filament painting made using Bambu Pla Matte filaments.

(I use Bambu Lab x1c and I do not need use prime tower on this print)

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

Filaments Used:
PLA Bambu PLA Matte Charcoal Transmission Distance: 0.6
PLA Bambu PLA Matte Scarlet Red Transmission Distance: 2
PLA Bambu PLA Matte Mandarin Orange Transmission Distance: 3
PLA Bambu PLA Matte Lemon Yellow Transmission Distance: 4
PLA Bambu PLA Matte Marine Blue Transmission Distance: 2
PLA Bambu PLA Matte Ivory White Transmission Distance: 4

Swap Instructions:
Start with Charcoal
At layer #6 (0.56mm) swap to Scarlet Red
At layer #11 (0.96mm) swap to Mandarin Orange
At layer #12 (1.04mm) swap to Lemon Yellow
At layer #14 (1.2mm) swap to Marine Blue
At layer #15 (1.28mm) swap to Ivory White for the rest.

 

This is a filament blending model, I would recommend trying to match the td as close as possible if not using the exact filaments to get the best results

Use the exact numbers in your slicer to match up properly.

The Model is designed to print with 0.4 nozzle.

**If re-scaling model make sure not to alter the Z height of the model**

 

Mark the Centre at the rear and drill the required size hole for your clock movement.

Link for the movement that I used is listed below but any standard movement will be fine (be sure to check the size of the hands)

https://www.amazon.co.uk/dp/B0BBLXG55S?psc=1&ref=ppx_yo2ov_dt_b_product_details

Welcome and thankyou for your support.

This tier gives you early access to all of my designs and access to exclusive member only models to print with consent to sell the physical prints for financial gain.

Selling or sharing of the digital files is not permitted

please note that the commercial license to sell prints is only given to active ‘Seller’ members, if you choose to cancel your subscription the license will expire simultaneously.

Seller

Welcome and thankyou for the support, This tier gives you early access to all of my designs and access to exclusive member only models to print for personal use only.

Please note the files are not to be re-distributed or used for financial gain.

Personal Use

5 Color HueForge model. 'Spider-Man Clock' filament painting made using Bambu filaments.

if you are not familiar with printing at really fine layers such as 0.04 you will need to lower the print speed on printers like the Bambu

(I recommend the following speed settings for the Bambu with 0.04 layers, inner walls, outer walls and gap infill - 200mm/s, sparse infill, internal solid infill and top surface - 150mm/s)

 

Print at 100% infill with a layer height of 0.04mm with a base layer of 0.24mm

Filaments Used:
PLA Bambu PLA Matte Charcoal Transmission Distance: 0.6
PLA Bambu PLA Matte Marine Blue Transmission Distance: 2
PLA Bambu PLA Matte Scarlet Red Transmission Distance: 1.5
PLA Bambu PLA Matte Lemon Yellow Transmission Distance: 4
PLA Bambu PLA Matte Ivory White Transmission Distance: 4

Swap Instructions:
Start with Charcoal
At layer #10 (0.6mm) swap to Marine Blue
At layer #15 (0.8mm) swap to Charcoal
At layer #19 (0.96mm) swap to Scarlet Red
At layer #22 (1.08mm) swap to Lemon Yellow
At layer #25 (1.2mm) swap to Ivory White for the rest.

At Layer #33 (1.44mm) swap to Charcoal for the border

At layer #41 (1.76mm) swap to Ivory White for the numbers (clock with numbers)
 

 

This is a filament blending model, I would recommend trying to match the td as close as possible if not using the exact filaments to get the best results

Use the exact numbers in your slicer to match up properly.

The Model is designed to print with 0.4 nozzle.

**If re-scaling model make sure not to alter the Z height of the model**


ALL Ian Smalley's designs are protected by Copyright Law. Downloading does not give you permission to use the files or physical prints for financial gain. If you want a commercial license to Legally sell prints from my designs, you will need a SELLER subscription.
 

add a negative cylinder to the Centre of the model in slicer to create the correct size hole for your movement or alternatively mark the Centre at the rear and drill the required size hole.

Link for the movement that I used is listed below but any standard movement will be fine (be sure to check the size of the hands)

https://www.amazon.co.uk/dp/B0BBLXG55S?psc=1&ref=ppx_yo2ov_dt_b_product_details

Spider-Man Clock (Filament Painting)

Spider-Man Clock (with border).stl

Spider-Man Clock (Border with line number markers).stl

Spider-Man Clock (border with numbers).stl

Filament painted print made using HueForge - Filament swaps ONLY, no mmu/ams required

5 Colour ‘filament painting’ model, Santa

 

(I recommend the following max speed settings, inner walls, outer walls and gap infill - 200mm/s, sparse infill, internal solid infill and top surface - 150mm/s)

 

Print at 100% infill with a layer height of 0.04mm with a base layer of 0.24mm

Filaments Used:
PLA Bambu PLA Matte Charcoal Transmission Distance: 0.6
PLA Bambu PLA Matte Marine Blue Transmission Distance: 2
PLA Bambu PLA Matte Ivory White Transmission Distance: 4
PLA Bambu PLA Matte Scarlet Red Transmission Distance: 1.5
PLA Bambu PLA Matte Lemon Yellow Transmission Distance: 3
 

Swap Instructions:
Start with Charcoal
At layer #7 (0.48mm) swap to Marine Blue
At layer #9 (0.56mm) swap to Ivory White
At layer #12 (0.68mm) swap to Charcoal
At layer #13 (0.72mm) swap to Scarlet Red
At layer #16 (0.84mm) swap to Lemon Yellow
At layer #18 (0.92mm) swap to Ivory White for the rest.
 

I would recommend trying to match the td as close as possible if not using the exact filaments to get the best results

Use the exact numbers in your slicer to match up properly.

The Model is designed to print with 0.4 nozzle.

**If re-scaling model make sure not to alter the Z height of the model**

 

ALL of Ian Smalley's designs are protected by Copyright Law. Downloading does not give you permission to use the files or physical prints for financial gain. If you want a commercial license to Legally sell prints from my designs, you will need a SELLER subscription.

Santa 'Filament Painting'

santa vector_Front_150x150.stl

santa vector_Front_200x200.stl

santa vector_Front_150x150 bambu 3mf.3mf

santa vector_Front_200x200 bambu 3mf.3mf

5 Colour E.T clock, made using Bambu filaments.

Filament painted print made using HueForge - Filament swaps ONLY, no mmu/ams required

(I recommend the following max speed settings, inner walls, outer walls and gap infill - 200mm/s, sparse infill, internal solid infill and top surface - 150mm/s)

 

Print at 100% infill with a layer height of 0.04mm with a base layer of 0.24mm

Filaments Used:
PLA Bambu PLA Matte Charcoal (Black) Transmission Distance: 0.6
PLA Bambu PLA Matte Marine Blue Transmission Distance: 2
PLA Bambu PLA Matte Ice Blue Transmission Distance: 3.5
PLA Bambu PLA Basic Jade White Transmission Distance: 5

PLA Bambu PLA Matte Lilac Purple Transmission Distance: 2

Swap Instructions:
Start with Charcoal (Black)
At layer #11 (0.64mm) swap to Marine Blue
At layer #18 (0.92mm) swap to Ice Blue
At layer #23 (1.12mm) swap to Jade White
At Layer #34 (1.56mm) swap to Charcoal (Black) for the border
At Layer #39 (1.76mm) swap to Lilac Purple for the numbers

 

I would recommend trying to match the td as close as possible if not using the exact filaments to get the best results

Use the exact numbers in your slicer to match up properly.

The Model is designed to print with 0.4 nozzle.

**If re-scaling model make sure not to alter the Z height of the model**

 

add a negative cylinder to the Centre of the clock in the slicer to create the correct size hole for your movement or alternatively drill the required size hole.

Link for the movement that I used is listed below but any standard movement will be fine (be sure to check the size of the hands)

https://www.amazon.co.uk/dp/B0BBLXG55S?psc=1&ref=ppx_yo2ov_dt_b_product_details

 

ALL of Ian Smalley's designs are protected by Copyright Law. Downloading does not give you permission to use the files or physical prints for financial gain. If you want a commercial license to Legally sell prints from my designs, you will need a SELLER subscription.

E.T Clock

E.T Clock.stl

Hueforge tester, creating 3d printed filament paintings, using 3d printers to create art

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Ian_Smalley

Pinned models

Spider-Man Clock (Filament Painting)

Santa 'Filament Painting'

E.T Clock

Han Solo Carbonite (Filament Painting)

Rocket Clock (Filament Painting)