Simple holder with compartments for AA and AAA batteries. It requires a minimum amount of plastic to print. 
I don't like the idea of having different organizers for these two types of battery so I created this design to keep them all in one place. You can also print dividers to separate discharged batteries and keep them in the same place. 

**Versions**

- Smaller (42x84x25mm)
- Smaller with Gridfinity base (2x1 slots)
- Bigger (42x168x25mm)
- Bigger with Gridfinity base (4x1 slots)

Gridfinity versions are identical to normal but have a solid bottom with grid slots.

**Printing**

- 2 wall perimeters
- outer/inner wall printing order
- doesn't require infill
- 3 bottom shell layer

Battery Holder with optional Gridfinity base 

BatteryHolder_4slots.stl

This set of boxes is designed specifically for storing cables. They have a lightweight design to use a minimum amount of plastic. The extended container's edge prevents cables from slipping out. 
These boxes are alterations of my original design (https://thangs.com/designer/Dead.Pixel/3d-model/Cable%20Organizing%20Box%20-1131054) but are adapted to work with Gridfinity modular system. I tried to keep them as light as possible and they are just a little bit bigger and heavier than the previous. But if you are not interested in using grid system I would recommend to stay with original model.

The boxes are made in 6 sizes and have variations with or without slots for magnets on the bottom side. All of them are two slots wide but vary in length.

Used slots on a grid	Dimensions, mm	  Compartments	 Weight, g
   2x1	                        42x84x66	           2	                        28 (29)
   2x2	                        84x84x66	           4	                        45 (48)
   2x3	                        126x84x66	           6	                        63 (66)
   2x4	                        168x84x66	           8	                        80 (84)
   2x5	                        210x84x66	           10	                97 (102)
   2x6	                        252x84x66	           12	                114 (120)

**Printing recommendation**

I recommend using PETG or PLA+ for better durability but regular PLA will also work fine.
Should be printed without supports. 
You need magnets of 6mm diameter and 2mm thickness for variant with magnet slots. But it is not necessary to use magnets in every slot. It's up to you to decide where to place them.

**Compatibility**

This organizer is ideally suited for managing short (up to several meters) flexible cables. It is **not suitable** for thicker or stiffer cables like HDMI, DisplayPort, and similar types.

Gridfinity Cable Organizing Boxes

CableOrganizingBox_2x1.stl

CableOrganizingBox_2x4.stl

A box designed specifically for storing cables. You can choose from one of three sizes. It has a lightweight design and requires only 65g to 85g of plastic to print depending on the size. I recommend using PETG or PLA+ for better durability. The extended container's edge prevents cables from slipping out.
The box's dimensions are:
9 compartments - 172mm x 81mm x 60mm (suitable for A1 mini without scaling)
10 compartments - 201mm x 81mm x 60mm
12 compartments - 241mm x 81mm x 60mm

If you are looking for a box compatible with Gridfinity try my another design https://thangs.com/designer/Dead.Pixel/3d-model/Gridfinity%20Cable%20Organizing%20Boxes-1131056?source=All+Files. I tried to keep the same lightweight concept and combine it with the benefits of the grid modular system. The boxes from that set have more size variants but are slightly bigger and heavier so it's up to you to choose which is better for your needs. 


**Compatibility**

This organizer is ideally suited for managing short (up to several meters) flexible cables. It is **not suitable** for thicker or stiffer cables like HDMI, DisplayPort, and similar types.

Cable Organizing Box 

CableOrganizer9.stl

I designed this stand for my Pitbull Skull Shaver to let it drip and dry after wet shaving but it can be used with any shaver of this type.
It is compatible with shaver heads of up to 65mm wide. Let me know if you need a bigger size.

Shaver Stand

Shaver Stand Top.stl

Small simple tool to sand small parts. Dimensions: 100mm x 50mm x 40mm. 
The handle provides a more ergonomic grip and skewed sides allow it to reach narrow parts or sharp inner corners.

 
**Instructions**

Requires non-3D printed parts:
- 1x M5 Screw with low profile cap (15-27mm long)
- 1x M5 Nut

Despite it can be printed without supports I would recommend using a small support for the hole in the base part.

Print all three parts. Put M5 nut inside the printed “Nut” part. Place “Nut” inside “Handle” making sure that metal nut is on top. Put the screw through the hole at the bottom of “Base”, then through “Handle” with “Nut”. Turn the “Nut” until it will be tighten enough. 

Sanding Block / Sanding Tool with Handle

Handle.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Dead.Pixel

Achievements

Seedling

Fan Favorite

Battery Holder with optional Gridfinity base

Gridfinity Cable Organizing Boxes

Cable Organizing Box

Shaver Stand

Sanding Block / Sanding Tool with Handle