**Pull the pin and throw them fast, they will explode!!
Transform your Water Balloons in Water Grenades
Share your prints!!**

**INSTRUCTIONS:**
Intoduce the tip of the balloon and clip it in, then secure it with the pin.

You can use a spring from any kind of pen to make the latch fly off when thrown and to ensure the balloon is released. 

MAX spring diameter 5mm (Maybe you will need to cut the spring to length)
 
**Follow me on:**

Instagram: https://www.instagram.com/afo3d/

TikTok: https://www.tiktok.com/@afo3d

Youtube: https://www.youtube.com/@AFO3D

 

**Licensing**
All my designs are non-commercial and may not be sold, reproduced, or shared outside of this website.
If you wish to sell any of them you must subscribe to my Thangs.com or Printables.com
Commercial membership plans.

-AFO

BALLOON GRENADE

BALLOON_GRENADE.3mf

Here you shall find all my gadgets, I hope they serve you well!!

GADGET SHOP

**PRINT-IN-PLACE HAR CLAW CLIP**

This is the perfect gift for your mom this Mother's Day, it's not a remix, it's a complete redesign from my previous hair clip. It works better and the smaller version prints great.
 
**FOR THE LARGE MODEL YOU NEED TO REMOVE THE INCLUDED SUPPORTS WITH THE HELP OF A CUTTING BLADE**

THE SMALL ONE JUST NEEDS A CLEAN UP



**Follow me on:**

Instagram: https://www.instagram.com/afo3d/

TikTok: https://www.tiktok.com/@afo3d

Youtube: https://www.youtube.com/@AFO3D

 
**Reccomended Print Settings:**
Filament: PETG (don't use PLA)
Layer Height: 0.20
Infill: 100%
Support: On buildplate only
 
-AFO

HAIR CLAW CLIP (REDESIGN)

HAIR CLAW CLIP REDESIGN LARGE.stl

**Use your 0.2 mm Nozzle to print a small chess game and have some fun playing against ANTS.**

 
**THERE IS TWO VERSIONS:**

THE BIGGER version uses BIGGER MAGNETS: 4mm x 2mm (96 magnets needed)

**LINK FOR THE 4mm x 2mm MAGNETS**:
https://amzn.to/3Jn1uka

(this is an affiliate link i would appreciate if you use it TY)


THE SMALLER version uses SMALLER MAGNETS: 2mm x 1mm (96 magnets needed)

**LINK FOR THE 2mm x 1mm MAGNETS:**

https://amzn.to/3xE1R7n

(this is an affiliate link i would appreciate if you use it TY)

 

**You can play using this tweezers:**
https://makerworld.com/en/models/433868#profileId-338654



**YOU HAVE THREE OPTIONS FOR THE MAGNETS:**

1.NOT USING THEM (EASY)
2.GLUING THEM AFTERWARDS
03.EMBEDDING THEM MID-PRINT


**Follow me on:**

Instagram: https://www.instagram.com/afo3d/

TikTok: https://www.tiktok.com/@afo3d

Youtube: https://www.youtube.com/@AFO3D


Reccomended Print Settings:
- Multicolor
- 0.2mm Nozzle
- Brim
 

 

- AFO


MINI CHESS GAME

CHESS+BOARD+EMBEDDED+MAGNETS(3).3mf

**The best gift for your mom it's the memories that you have with her, memories are freezed in time by photograpy, this gift captures the images in a little film keychain.**

Customize the photos and print the film in the [this video.](https://www.canva.com/design/DAGDu152i7U/hTfYTWck00zAbRB0bmSYlQ/view?utm_content=DAGDu152i7U&utm_campaign=designshare&utm_medium=link&utm_source=publishsharelink&mode=preview)

 

**Follow me on:**
Instagram: https://www.instagram.com/afo3d/

TikTok: https://www.tiktok.com/@afo3d

Youtube: https://www.youtube.com/@AFO3D


**Reccomended Print Settings:**
- Brim
 

-AFO

PHOTO FILM KEYCHAIN

KODAK+PHOTO+FILM+ROLL.3mf

**KEEP YOUR MOST VALUABLE THINGS HIDDEN WHILE YOU TAKE A DIP INTO THE SEA.**

It includes an AirTag compartment so you can bury it and find it with ease and a little print-in-place handle to carry it.


**NEW VERSION IMPROVEMENTS:**
- LOCKER KEY FOR EXTRA SECURITY.
- NO THREADS  (sand gets stuck and blocks them sometimes)
- BETTER AIRTAG LOCKING CAP
- PRINT IN PLACE
- STRONGER HANDLE
 - BIGGER AND POINTIER
- Share your prints!!

(ASA or ABS is recommended)

 

It's recommended to use the print profile provided, supports are already in place and tolerances tested.
Assembly:
I used this 16mm locker key: https://amzn.to/4drbgi3
(This is an affiliate link)


1. INESRT THE SAND SHIELD ON THE LOCKER KEY
2. TIGHTEN THE LOCKER KEY FROM THE OTHER SIDE WITH THE NUT
3. ALIGN THE METAL LATCH AND TIGHTEN THE SCREW THE LATCH NEEDS TO BE ALIGNED WITH THE KEY LIKE SHOWN, TO LOCK IN PLACE.
4. AND YOU ARE DONE!
 
Maybe you will need to help the cap come loose with some plyers.

**Follow me on:**
Instagram: https://www.instagram.com/afo3d/
TikTok: https://www.tiktok.com/@afo3d
Youtube: https://www.youtube.com/@AFO3D


**Licensing**
All my designs are non-commercial and may not be sold, reproduced, or shared outside of this website.
If you wish to sell this model print, subscribe to my thangs commercial license.

-AFO

AFO3D

Achievements

Seedling

Debutant

Pinned models

SAND SAFE 2 (With Keys and AirTag)

PHOTO FILM KEYCHAIN

MINI CHESS GAME

BALLOON GRENADE

BALLOON GRENADE

GADGET SHOP

HAIR CLAW CLIP (REDESIGN)

MINI CHESS GAME

PHOTO FILM KEYCHAIN

SAND SAFE 2 (With Keys and AirTag)