Safety clip (Clip de racor)

It is a safety clip for the pneumatic fitting or for a 4mm outer diameter quick connector for 3D printer.

The G-code is created with PrusaSlicer for Prusa mini with an ultra definition of 0.05 mm; but it can also be printed for Creatity and other printers that use Marlin, (if you have a glass bed with clamps, make sure before putting it on, to remove the front clamp on the left, to prevent the nozzle from colliding with it, when doing the first line of filament checking), since PrusaSlicer does it on the front of the hot bed, not like Cura, which does it on the left.

 

Il s'agit d'un clip de sécurité pour le raccord pneumatique ou pour un connecteur rapide de 4 mm de diamètre extérieur pour imprimante 3D. 

Le code G est créé avec PrusaSlicer pour Prusa mini avec une ultra définition de 0,05 mm ; mais il peut également imprimer pour Creatity et d'autres imprimantes qui utilisent Marlin, (si vous avez un lit en verre avec des pinces, assurez-vous avant de le mettre en place, que vous retirez la pince avant gauche, pour éviter que la buse n'entre en collision avec (lors de la vérification de la première rangée de filaments), puisque PrusaSlicer le fait sur le devant du lit chaud, pas comme Cura, qui le fait sur la gauche.

 

Se trata de un clip de seguridad para el racor neumático o para un conector rápido de 4 mm de diámetro exterior para impresora 3D. 

El código G está creado con PrusaSlicer para Prusa mini con una ultra definición de 0,05 mm; pero también se puede imprimir para Creatity y otras impresoras que usan Marlin, (si tienes una cama de cristal con abrazaderas, asegúrate antes de ponerla, de quitar la abrazadera frontal de la izquierda, para evitar que la boquilla choque con ella, al hacer la primera línea de comprobación de filamento), ya que PrusaSlicer lo hace en la parte frontal de la cama caliente, no como Cura, que lo hace en la izquierda.

Ender 3 Display Stand

Ender 3 Display Stand.stl

Vibration Damping Feet

Vibration Damping Feet (1 nut).stl

3D Printer Status Board / Name Board (Print-in-place)

Frame.STL

Ender 3 PTFE Adaptor

adapter to use a ptfe fitting.
I built this adapter to connect the bowden printer to the filament bunker.

Ender 3 Speaker Modifier

Ender_3_Speaker_Modifier_Quiet.stl

light strip clips MK3 (open ended)

I made this for my own light strip that i ordered from amazon.
Light clips sit between the top bolts

link is for those wanting it, its NOT an affiliate link.

https://amzn.eu/d/3mR5AXP

Free-Standing PSU Stand

Free-Standing PSU Stand Legs v3.stl

Creality Enders Starlex 22 Butterfly A4010 R5015 fans shroud

Swiss3Dc-Starlex-Cr-Butterfly-Fans-4011-5015-BL-B2.STL

All in One BIQU H2 Mount

H2MOUNT_A.3mf

Low Friction Spool Holder Adapter

Low Friction Spool Holder Adapter

Are you like me and upgraded your bowden tube, but held on to the old one?

Well you are in luck!  Use it as part of this adapter to reduce friction between your spool and the spool holder.

Designed primarily for the Ender 3, but any similar spool holder should work.

Yes this is a mashup, however it does have significant changes and qualifies as unique work.  See license.txt for more details.

1. Cut two bowden tubes to fit in side of each track.
2. Remove the tube from your spool holder and snap on the adapter.
3. Put the tube back on the spool holder.
4. Enjoy

- Easy snap fit!
- Bowden tubes are low friction by design.
- The curved shape further reduces friction by limiting contact with the spool to two points.
- The curved shape uses gravity to keep the spool centered on the spool holder.

Supports are required. I would suggest using support blocker on the bowden tube holes, they seem to print fine.  

* I used tree supports and a brim.
* I printed at 5° hotter than normal to help with layer adhesion.
* I printed at 0.12 for a smoother look. However during testing I printed at 0.2 and it worked without issue.


Ender 3 series PTFE-to-Creality Direct Drive Extruder Arm Conversion

Since humidity is an issue in my area, I use Rubbermaid 21 cup dry boxes with a reverse Bowden setup on all my printers to minimize the filament's exposure to the air. My Ender 3 Pro is setup for direct-drive extrusion. The stock Creality extruders (plastic and aluminum) don't have a threaded inlet for a PTFE fitting. I'm not content with using a stop at the top 2020, which leaves a good amount of filament exposed, subject to getting brittle, causing breakage. I designed this glue-on conversion for the Creality extruder arms and will work with any PTFE fitting that use the M6 threaded ends.

My top-most criteria was to have it strengthen the plastic version of the Creality extrusion arms, hence the thickness or height of the conversion piece. I also wanted to make sure torque on the PTFE fitting, while the hotend was traversing the X-gantry, wouldn't cause the conversion to loosen up or break due to flexing.

I decided to tap the threads instead of designing them in. Ample reinforcement has been added around the hole so that tapping won't break into the infill. With this method the size and shape of the threaded hole is guaranteed regardless of the filament used and the accuracy of the printer.

If you don't have an M6x1.0 tap, and aren't interesting in acquiring one, you can make one by:

1 - filing two opposing grooves along half the length of an M6x1.0x10+mm screw with a jeweler's file

2 - running it in and out of the hole a little at a time, until the threads are cut all the way through the hole.

15% infill with a Grid pattern is ample as long as you use at least 4 walls (perimeters) I recommend 6. 5-minute epoxy and small hobby clamps will secure the conversion piece to the topside of the extruder arm, which should be done with the arm removed from the extruder. Make sure no epoxy gets into the PTFE threaded area or in the filament hole of the arm. Leave overnight to fully cure.

The two extruders shown are the plastic model that comes on the Creality Ender 3 series and the red anodized aluminum one (on my Ender 3 Pro) that comes with the Creality direct drive kit.


1,25L Bottle Holder For Fridge

Bottle holder.stl

TerraMesh Crossbody Bag | 3D-Printed Wearable Bag | Fashion Accessory | 3A Creates

ender3

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Safety clip (Clip de racor)

Ender 3 Display Stand

Vibration Damping Feet

3D Printer Status Board / Name Board (Print-in-place)

Ender 3 PTFE Adaptor

Ender 3 Speaker Modifier

light strip clips MK3 (open ended)

Free-Standing PSU Stand

Creality Enders Starlex 22 Butterfly A4010 R5015 fans shroud

All in One BIQU H2 Mount

Low Friction Spool Holder Adapter

Ender 3 series PTFE-to-Creality Direct Drive Extruder Arm Conversion

1,25L Bottle Holder For Fridge

TerraMesh Crossbody Bag | 3D-Printed Wearable Bag | Fashion Accessory | 3A Creates

3D Printer Door Frame Enclosure

ender3v1_ledstrip_hanger.stl

legs for ender 3

Creality Ender 3 S1 Mini PC Bracket

Andantio / Six Tiles (Eay Print)

Ender3 Hot-Swap Hot-End Mount