AMS Feed Protector Button
A different design on the button. 
Remix of: 
OurAngryBadger - https://www.printables.com/model/329082
ktothestank - https://www.printables.com/model/306625-bambu-ams-feeder-pfte-adapter
scorf - https://www.printables.com/model/390800-bambu-ams-feeder-protector-adapter

AMS Feed Protector Button (remix)

AMS Feed Protector Button (tubeless) v0.1 rlm .stl

I wanted to vent the exhaust from my Bambu Labs X1C through a filter then outside. The original model would not work without modification. The other remixes were close, but not quite what I was looking for. 

Print times are roughly 3hr on normal, and 1.5hr on ludicrous.

This model is a remix of: https://www.printables.com/model/280283

Bambu X1C Vent Adapter

I wanted to vent the exhaust from my Bambu Labs X1C through a filter then outside. The original model would not work without modification. The other remixes were close, but not quite what I was looking for. 

Print times are roughly 3hr on normal, and 1.5hr on ludicrous.

I use lighters for heat shrink all the time. This tray will keep two lighters handy at all times.

This 1x2 Gridfinity tray has custom slot that will hold two Bic (or similar) lighters.

Gridfinity Bic Lighter Tray

Gridfinity Bic Lighter Tray (two slot, fa) v0.1 rlm .stl

Vibration Damping Feet

This model uses rubber stoppers to dampen vibrations between the printer and work surface.

- Easy twist-in or M5 T-nut versions
- 2020 and 2040 (etc.) compatible
- Glue not required
- Keeps printer stationary. 
- Optionally, you can cut a small circle of paper to put between the rubber stopper and work surface if you like to move your printer around.


East twist-in version:
- Easy twist-in design!
- May need additional post processing.
- May need supports.

M5 T-nut version:
- No support needed!
- No additional post processing.
- M5 T-nut and bolt required.

*You may need to resize the model to match your tolerances.

Rubber stoppers on Amazon: https://amzn.to/3U1YNHP

Just FYI: Damping and Dampening are synonymous. (Yes, I had to say it.)
Rubber stoppers not included.
T-nuts not included.

Vibration Damping Feet

Vibration Damping Feet (1 nut).stl

Xacto Knife tray insert for Gridfinity with 1 slot.

Rather than dedicating a 1x3 (gridfinity units) exclusively as an Xacto knife tray, give this insert a try.
The insert fits inside an 1x3, or can be used stand alone on your work surface.

Gridfinity Xacto Knife Tray Insert (1 slot)

Xacto Knife tray insert for Gridfinity

Rather than dedicating a 1x3 (gridfinity units) exclusively as an Xacto knife tray, give this insert a try.
The insert fits inside an 1x3, or can be used stand alone on your work surface.

Optional models:
Model B (squares at both ends)

Gridfinity Xacto Knife Tray Insert (3 slot)

Gridfinity Xacto Knife Tray Insert A (3 slot) v0.1 rlm .stl

Low Friction Spool Holder Adapter

Are you like me and upgraded your bowden tube, but held on to the old one?

Well you are in luck!  Use it as part of this adapter to reduce friction between your spool and the spool holder.

Designed primarily for the Ender 3, but any similar spool holder should work.

Yes this is a mashup, however it does have significant changes and qualifies as unique work.  See license.txt for more details.

1. Cut two bowden tubes to fit in side of each track.
2. Remove the tube from your spool holder and snap on the adapter.
3. Put the tube back on the spool holder.
4. Enjoy

- Easy snap fit!
- Bowden tubes are low friction by design.
- The curved shape further reduces friction by limiting contact with the spool to two points.
- The curved shape uses gravity to keep the spool centered on the spool holder.

Supports are required. I would suggest using support blocker on the bowden tube holes, they seem to print fine.  

* I used tree supports and a brim.
* I printed at 5° hotter than normal to help with layer adhesion.
* I printed at 0.12 for a smoother look. However during testing I printed at 0.2 and it worked without issue.

Works with Ender 3 and CR-10S.
Probably works with any Creality spool holder. I think the diameter is the same.

Low Friction Spool Holder Adapter

Low Friction Spool Holder Adapter

Are you like me and upgraded your bowden tube, but held on to the old one?

Well you are in luck!  Use it as part of this adapter to reduce friction between your spool and the spool holder.

Designed primarily for the Ender 3, but any similar spool holder should work.

Yes this is a mashup, however it does have significant changes and qualifies as unique work.  See license.txt for more details.

1. Cut two bowden tubes to fit in side of each track.
2. Remove the tube from your spool holder and snap on the adapter.
3. Put the tube back on the spool holder.
4. Enjoy

- Easy snap fit!
- Bowden tubes are low friction by design.
- The curved shape further reduces friction by limiting contact with the spool to two points.
- The curved shape uses gravity to keep the spool centered on the spool holder.

Supports are required. I would suggest using support blocker on the bowden tube holes, they seem to print fine.  

* I used tree supports and a brim.
* I printed at 5° hotter than normal to help with layer adhesion.
* I printed at 0.12 for a smoother look. However during testing I printed at 0.2 and it worked without issue.


Adjustable Phone or Tablet stand with a Celtic Claddagh theme

Celtic Claddagh Adjustable Stand

Celtic Claddagh Adjustable Stand v0.01 rlm - Back Claddagh .stl

Cute spider
GLOWING!
There is a hollow place for an LED Tea Light.

This is a remix of:
https://www.printables.com/model/299185-win-an-obxidian-nozzle-e3ds-halloween-competition
 Changes:
 - Enlarged
 - Hollowed out
 - Hole for Tea Light

Glowing Spider

Glowing Spider (large, hollow, closed) v0.5 rlm .3mf

Glowing Spider (small, hollow, 6 open) v0.5 rlm .stl

Glowing Spider (small, hollow, closed) v0.5 rlm .stl

Gridfinity compatible Caliper Holder

Optional models:

With slots for Rulers

With end cut (for smaller printers)

With slots for Rulers and end cut (for smaller printers)

Gridfinity Caliper Holder (horizontal)

Scary tree with Cute spider and web.
GLOWING!
There is a hollow place in the tree for an LED Tea Light.

Halloween Glowing Tree and Spider

Tree and Spider remix v0.3 rlm (set) .stl

Tree and Spider remix v0.3 rlm spider (small hollow) .stl

Scary tree with Cute spider and web.
GLOWING! 
There is a hollow place in the tree for an LED Tea Light.

Tree and Spider remix v0.3 rlm spider (hollow) .stl

Tree and Spider remix v0.3 rlm tree .stl

Tree and Spider remix v0.3 rlm web .stl

Remix to allow for an LED Tea Light to make the brain glow.

Frankenstein's Monster LED Tea Light Holder
Remix by: Robert Martin
Remix on: 10/20/2022
Original License: 
License: Creative Commons - Attribution - NonCommercial

Original: 
Frankenstein's Monster with Removable Brain  by yeg3d on Thingiverse: https://www.thingiverse.com/thing:1081535
Original License: 
Creative Commons - Attribution

Frankenstein's Monster with Glowing Brain

Frankenstein's Monster with Glowing Brain (brain) v0.3 rlm .stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

roborob