MODULAR SPOOL STAND

4x WHEEL.3mf

SPOOL ADAPTER  (for Creality)

MAIN.3mf

Camping / Unboxing Tool

BLADE_V2.3mf

All in One BIQU H2 Mount

H2MOUNT_A.3mf

PSU MOUNT.3mf

Modular Spool Holder (1kg Space Saver)

Centre_1ofeach.3mf

Heated Vacuum chamber components.
Intended for Premium Quality storage boxes.

You will need several different lengths of M3 hex screws: https://amzn.eu/d/2mAghbn

I also used
Spool Holder Bearings : https://amzn.eu/d/gFGBCHk
Hinge bearings: https://amzn.eu/d/bWtEBpv
Switches: https://amzn.eu/d/4ma39Dr
Heater fan : https://amzn.eu/d/1KPGOKE


HVC-DryBox

BIQU_H2 FULL HOTEND SETUP

I didn't make this one. I've ordered the hotend but decided to wait until it comes to begin trying to make anything for it. Seems so easy to mount I wonder how necessary an upload this is. I guess my verdict is waiting on delivery.

FULL ENDER 3 v1 MACHINE 

I didn't design this one. Intended to assist machine modification designs.

FULL ENDER 3

Hinges

LEFT.3mf

Feet.3mf

FootBase.3mf

60x60 FrontFanGuard.3mf

Grill.3mf

Power Switch Panel

Back.3mf

BIQU H2 Ender3 Cradle

All-in-One Extruder mount, Fan mount and Cable Organizer.

Support Required, Raft Recommended.



Recommended Application:

1, Apply the hook under the Hotend wires and loosely fix the bottom 1 of the 2 vertical screws on the reverse of the Cradle, to apply the Cradle to the H2.

2, Put the first front screw (upper one of diagonal pair) between the printer and Cradle through the hole (on the front of the Cradle) through the Cradle, just to put it in place on the Cradle - not to screw it into the printer yet.

3, Apply the 2nd of the vertical screws on the reverse of the Cradle, tightening them both, securing the Cradle to the Hotend, with the first front screw of the previous step hanging in place.

4, Slide the wire of Fan1 (red+black wire) between the air outlet and the nozzle, so as to slide Fan1 into place (but not screw in yet).

5, Apply the 2nd of the diagonal pair of screws so as to mount the Cradle to the printer.

6, Screw in the 2nd fan, using the original screws, just tightly enough to catch the thread of the Hotend and lock in place, baring in mind the strength of the plastic.

7, Pull the Fan2 wire (blue+yellow wire) behind the Cradle across to past Fan1, allowing the wire to sit in the groove as you put Fan2 in place, screwing it in at the top right hand corner.


I should say, there are a couple minor tweaks yet to complete, including moving the 2nd Carriage to printer (diagonal pair) screw down about 4mm and allowing the first of those 2 screws to sit more flush with the side surface.

I2C 0.96 inch Screen Holder

Designed to mount the 0.96 Inch OLED Module 12864 128x64 SSD1306 to an SG90 Servo motor head for rotating display

SG90 Servo Cup Holder

Stabilizes the foot print of the servo, can screw into work top or use double sided tape.

KeyboardMount.stl

Mount for a wireless keyboard or tablet of up to 12mm depth. Intended for either screw or double sided tape adhesion. Symmetrical, requires 2x prints 

SimpleFunnel.step

The neck of the 1.5L Cocacola bottles are smaller than water bottles so I designed it for that at 1mm thickness though I'm sure you could Vase mode it but I'm guessing you will want a little weight to your funnel.

FOLCoaster.stl

YYCoaster.stl

Filament Hanger

Right-Hand side of filament holder intended to be used with a suitably cut wooden curtain pole (or broom stick etc). 

Right Hanger.stl

Ender 3 Filament Guide (Palette compatible)

Ender 3 Pro - Y Axis Tensioner Cover

Ender Feet (Shock Absorbers)

Experimental attempt to provide shock absorption by using the original bed springs.  I would recommend stretching springs before hand as I found there to be little travel between the two halves.

ENDER FEET

ASM Frame

ASM X-Axis

ASM Y-Axis

ASM Z-Axis

ASM Display

ASM Electronic Enclosure

ASM Spool Holder

ASM Power Supply

lowLEFT.3mf

Sides_x1set.3mf

Would be great to work on design projects, or fulfil requests. I consider myself very much a student though with flair and my touchdown in this field would be getting hired on a regular basis to design stuff. My personal goal is to make a magnetic generator 

AlphaZen

Achievements

Seedling

Fan Favorite

Explorer