I made this cool guitar hanger with invisible screws. The mount itself is printed with [GreenGate's "Devin Montes Cool Grey" 100% Recycled PETG Filament](https://bit.ly/coolGrey), and the top padding is printed with a flexible TPU like [Ninjaflex](http://bit.ly/ninjaFLEX)

Use the wall-plate to trace screw placement on your wall. Screw into a stud for best strength, or use quality anchors. Of course the strength will also come down to the print quality. I printed the PETG at 100% infill and it feels more than strong enough for my acoustic guitar, but use at your own risk! Make sure the arrow on the 'wall-plate' is pointing upwards, and use at least the top and bottom screw holes (middle if you want the extra strength)

The 'padding.stl' should friction fit onto the 'arm.stl' which slides onto the 'wall-plate'. If the flexible padding doesn't stay in place you can also glue it down with [E6000 adhesive.](https://amzn.to/45GlcAS)

I've included versions to fit varying guitar neck widths. The 50mm, 56mm, and 60mm versions indicate the maximum width at the first fret.

Guitar Wall Mount Hanger with Flexible Top

60mm_Arm.stl

This is the Filacaster (Filament Caster), my 3d printed guitar in the classic American axe style. This is a new upload, because the old one got messed up when I was versioning and there were multiple copies of the same parts that I couldn't remove. 

This guitar is split into 9 elements to facilitate printing on most desktop FDM printers. The parts are referenced with 4.75mm printable layout pins and should be epoxied together. 

I would recommend adding some solid infill in your slicer around the tremelo block mounting points and printing the 3 center elements with a high infill (+50%) to increase strength. 

I have printed an earlier version of this guitar without the holes and while it does play, it is heavy, cumbersome without the tummy cut and probably not comparable to a real guitar in terms of intonation stability and the like. 

Since I printed the prototype, I've added the hexagonal holes, not so much as a design choice but as a way to reduce weight. I know this pattern is played out these days but I really did print the original in May 2021, before there were dozens of printed stratoclones all over the printer-verse.

A standard Strat style pickguard should fit, but I've included a two part guard that follows the hex cutouts and has some additional mounting holes.

Print with high infill, support from the bed. I printed the prototype with an 0.8 nozzle but I'm sure it would look even better with 0.4 and ironing enabled, time permitting.

When I print this newer version I will upload photos of it, in the meantime I added some pictures of the prototype without the holes. Please excuse the epoxy stains, I wasn't careful. :)

UPDATE

Forgot to add the slot for the selector switch to the bottom of the pick guard. Oops.

Filacaster

Fused.stl

Guitar pick guitar keychain. The name says it all xD. 
Check more projects on: https://www.youtube.com/channel/UCp3sDRwVkbm7b2M-2qwf5aQ/videos



Guitar pick guitar keychain

A Guitar shaped box with lid for storing guitar picks or anything else that will fit. Scale up for larger items

Guitar Box for guitar picks (Lid and Bottom half)

A Guitar shaped box with lid for storing guitar picks or anything else that will fit.

Guitar Box for guitar picks

guitarbottom.stl

guitartop.stl

Guitar pick triangle shape, with dimensions 33mm x 32mm x 2mm.
2mm thickness is flat part of pick (around grip).  Middle (grip part) is 2,5mm.

Diamond shaped middle, for better grip.

Guitar pick triangle - 33 x 32 x 2mm

guitar_pick_triangle.SLDPRT

Guitar pick wall hanging.  Scale for as large or small as you want.  Comes with hole in the back for easy hanging.  

Minimal infill required.  

Commercial resale license is available for this print with your Thangs.com membership to Makers Mashup.  Start selling these now in your etsy shop!

When it comes to hardware, I rely heavily on Bambu Lab 3D printers. My A1 Mini https://rb.gy/uofj5 is a staple in my office, while my fleet of X1C Carbons https://rb.gy/9r2az ensures rapid and high-quality production. #ComissionsEarned which help support my free model development.

🌟 *Love this model? Take a moment to support Rob (Makers Mashup) and get more involved!* 🌟

🎥 **Watch & Subscribe on [YouTube](https://youtube.com/MakersMashup)** - Assembly videos, tutorials, and much more. Don't miss out on new content!

🔗 **Join the Creative Journey on [Thangs.com](https://www.thangs.com)** - Subscribe to my profile for the latest models and exclusive content.

🤝 **Engage with the [Community Discord](https://discord.gg/ZDKq5N2)** - Get help and advice from over 1000 members. Build anything with the support of our community!

📲 **Get Social with MakersMashup** - 🐦 [Twitter](https://twitter.com/MakersMashup) | 📸 [Instagram](https://www.instagram.com/makers_mashup/) | 👍 [Facebook](https://www.facebook.com/MakersMashup)

❤️ **Support the Channel & Creator** - Your support makes a difference!
   - 🤝 [Patreon](https://www.patreon.com/makersmashup) – Support my ongoing work and get access to exclusive content!
   - 💸 Drop a tip: [Ko-fi](https://koji.to/k/8E9J)
   - 🛍️ Shop on Amazon? Click [this link](https://amzn.to/429HusI) before your next purchase. It helps the channel at no extra cost to you!

🔓 **Unlock Incredible Benefits!**
   - Resale Abilities with a Commercial Subscription on [Thangs.com](https://www.thangs.com)
   - Early Access to Models with a subscription on Thangs, YouTube, or Patreon
   - Request New Models as a subscriber

🚀 *Let’s build, share, and grow together!* 🚀


Guitar Pick Wall Hanging - #JunesTunes

Guitar pick wall hanging.  Scale for as large or small as you want.  Comes with hole in the back for easy hanging.  

Minimal infill required.  

Commercial resale license is available for this print with your Thangs.com membership to Makers Mashup.  Start selling these now in your etsy shop!

Was this model helpful for you? Consider supporting my work in any of the following ways!  Even the free options help the channel!

Consider dropping a tip https://koji.to/k/8E9J or
consider supporting my ongoing work https://www.patreon.com/makersmashup
Purchase anything on amazon after visiting our store page https://amzn.to/429HusI  Just click this link first!

No cost option to support my work?

- Subscribe to the YT channel
- Follow me on Thangs.com
- Watch videos on the channel!
- Share any of the videos on social media!
- Share my models with friends and family!



These are the the Tops for our Light Caster Guitar.  These were designed to be printed in translucent PLA to look like scale when lit up with lights.  We used COEX's "transparent blood" PLA for this project. 

Guitar Insert Scales

Guit1Scales.stl

Electric Guitar

Mesh1 OuterShell Model

Mesh2 OuterShell1 Model

Mesh3 Difference Model

Mesh4 OuterShell2 Model

Mesh5 Difference1 Model

Mesh6 Difference2 Model

Mesh7 OuterShell3 Model

Mesh8 Difference3 Model

Mesh9 Difference4 Model

Mesh10 Group1 Model

Mesh11 OuterShell4 Model

Mesh12 Group2 Model

Mesh13 Group3 Model

Mesh14 OuterShell5 Model

Mesh15 Group4 Model

Mesh16 Group5 Model

Mesh17 Group7 Group6 Model

Mesh18 Group8 Group6 Model

Mesh19 Group9 Group6 Model

Mesh20 Group10 Group6 Model

Mesh21 Group11 Group6 Model

Mesh22 Group12 Group6 Model

Mesh23 Group13 Group6 Model

Mesh24 Group14 Group6 Model

Mesh25 Group15 Group6 Model

Mesh26 Group16 Group6 Model

Mesh27 Group17 Group6 Model

Mesh28 Group18 Group6 Model

Mesh29 Group19 Group6 Model

Mesh30 Group20 Group6 Model

Mesh31 Group21 Group6 Model

Mesh32 Group22 Group6 Model

Mesh33 Group23 Group6 Model

Mesh34 Group24 Group6 Model

Mesh35 Group25 Group6 Model

Mesh36 Group26 Group6 Model

Mesh37 Group27 Group6 Model

Mesh38 Group28 Group6 Model

Mesh39 Group29 Group6 Model

Mesh40 Group30 Group6 Model

Mesh41 Group31 Model

Mesh42 Group31 Model

Mesh43 Group31 Model

Mesh44 Group31 Model

Mesh45 Group31 Model

Mesh46 Group31 Model

Mesh47 Group33 Group32 Model

Mesh48 Group34 Group32 Model

Mesh49 Group35 Group32 Model

Mesh50 Difference5 Group32 Model

Mesh51 Group36 Group32 Model

Mesh52 Group37 Group32 Model

Mesh53 Difference6 Model

Mesh54 Difference6 Model

Mesh55 Difference7 Model

Mesh56 Difference8 Model

Mesh57 Difference8 Model

Mesh58 Difference8 Model

Mesh59 Difference9 Model

Mesh60 inlays1 Model

Mesh61 inlays2 Model

Mesh62 inlays3 Model

Mesh63 inlays4 Model

Mesh64 inlays5 Model

Mesh65 inlays6 Model

Mesh66 inlays7 Model

Mesh67 inlays8 Model

Mesh68 inlays9 Model

Mesh69 inlays10 Model

Mesh70 inlays11 Model

Mesh71 inlays12 Model

Mesh72 Intersection warmothlogo1 Model

Screamer Trumpet Mouthpiece,
I put this together as an experiment to find the right sizes for me while looking for a mouthpiece.
I've made the bore a little smaller so that you can drill it out to the size that you want. just start with a small drill bit and play the mouthpiece, repeat this until you have the feeling that you want from it.
I've printed mine with 10 top layers and at 90% in PETG so that I can modify it easily after its printed. sand it and smooth it with a hot air gun to get best results.
I turned out to be a good mouthpiece and I can easily blow across the total register, pedals up to above high F with it.
I'm not a professional, just a hobbyist trying to find what works for me.
it would look better in ABS filament, then smoothed with acetone. but I don't have any ABS filament.
Have Fun.

Screamer Trumpet Mouthpiece

STL file for 3D printing a replacement Hercules guitar stand adjuster as the original fails very commonly, and NO Hercules do not supply a replacement part.

I have a video of me fitting this on youtube, please feel free to like/comment/subscribe

https://www.youtube.com/channel/UCpy2LPYeFDK8X-l0XhmKA4A

HERCULES Guitar stand adguster replacement.stl

STL file for 3D printing a replacement Hercules guitar stand adjuster as the original fails very commonly, and NO Hercules do not supply a replacement part   

I designed and 3D printed a protective box to organize a Lavalier Microphone.

The lid can simply be screwed onto the box with nothing else needed.

**Print Settings**

Depending on the size of you print bed, in the slicer you might have to split the model into parts and auto align it on the bed.

PLA Filament (Prusament)
Print Temp: 215°C First Layer / 210°C 2nd Layer onward
Perimeters: 2
Infill: 15%

I am printing with a Creality CR-6 SE

Check out my YouTube Video for more details: https://youtube.com/shorts/FZR89YLYmjQ

License Type = CC BY-NC-SA
(CC Attribution-NonCommercial-ShareAlike)

Protective Box for Lavalier Microphones with Srew-on Lid

Lav Mic Box - V1.stl

Slipknot guitar pick, Wall hanger, measures about 275 mm. 

slipknot-guitar-pic.stl

These are little guitar pick holders for your string instruments. I used the filament swap function on my MK3 to have the white details on top of the guitar body.

You don't need any support while printing this model because the bridges are too little to worry about. 

**Every make will be featured on my Instagram add your handle and follow me :)** Check out [my Instagram](https://www.instagram.com/tomo_designs/) if you want to see more designs like this or if you have questions!

happy easter everybody!

[Here](https://youtu.be/g-U49XYFXtE) you can see a more detailed look at my other design.
![](https://youtu.be/oMc8vY-9kbI)

You can also become a seller of all my designs. Check out my <a href="https://www.patreon.com/TomoDesigns/">Patreon</a>

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND


Guitar Pick Holders - Small Guitars easy print

Guitar pick holder 1.stl

**Pick Holder**
This is a cool little 3D Printed guitar pick holder. It holds around 3-4 picks. My design used a spring I found inside of an old machine. But the design can be easily changed for any type of spring. It is a cool little design and a fun thing to keep around

**_Surprise_**

This guitar pick design also has a surprise Shrek face on it if you want it! If not you can print out the plane guitar face.

#JuneTunes


Spring Loaded Guitar Pick Holder

Pick Holder v6.step

This is a bagpipe chanter utilizing a membrane reed.

Print all the parts in vertical orientation with supports (except for the outer chamber, as it's easy to jam up the threads. If your printer struggles with bridging, my trick for support removal was to insert an open scissors into either side of the section and "unscrew" the supports by twisting counterclockwise).

Wrap PTFE tape around the threads and verify an airtight connection. Alternately, you can try packing the grove where the outer chamber sits with heavy instrument grease (chapstick works great) which may also form an airtight seal. 

Screw the outer chamber onto the inner until the outer and inner cylinders are flush with one another (doing this against a mirror, countertop, or ideally granite surface plate helps), and use 400 grit sandpaper with a splash of water to ensure evenness. Check the evenness is airtight by sucking on the air inlet while pressed against the surface, covering the body tube section with a finger.

To make the membrane, many different materials are possible and produce different tones and performance. At the time of writing my favorite material is mylar emergency blanket material, which is what this design is optimized for. Cut a square or circle of material larger than the outer chamber and use the tension ring to attach it to the outer chamber. You want a smooth surface with no wrinkles, but NOT an overly tight "drum." This can take a few tries, but you can even out wrinkles by holding the tension ring and pulling the excess mylar side-to-side.

Next, trim the mylar to size, again while still holding the tension ring in place! When you have a clean attachment with ~2mm of overhanging mylar, put the onion dome on. This will conceal the excess mylar and protect the membrane. Finally, set the initial tension by slowly screwing the outer cylinder against the inner while blowing through the air intake. When you begin to hear a sound, stop, and put the body tube in (to be included soon - currently I am using garden pipe - see image).

Tune the pipe against itself by checking the octave (second-to-lowest note and highest note). If the octave is flat, the membrane needs tightening. If the octave is sharp, the membrane needs loosening. Then, tune the pipe to a tuner by moving the body tube in and out of the inner chamber's tenon.

Membrane Reed Bagpipe Chanter

Inner.stl

Ensure that your guitar strap stays on with this Strap Cap. It fits over a standard guitar strap button to make sure your guitar doesn't drop to the floor so you can jam with confidence!

In my case I didn't actually use it for a guitar, but a Jerry Jones 'electric sitar'.

---

Print at 100% infill and 1 shell 

[Relevant Video](https://www.youtube.com/watch?v=O5QJbhx4uKM)



Strap Cap // Guitar Strap Lock

strapcap-outer.stl

Shure MV7 cover

microfone_cover-04.stl

Wedge Screamer Trumpet Mouthpiece,
Just for fun.
I put this together to play with different ideas and to find what worked for me.
I printed mine in PETG with very small bore then this allowed me to drill out the bore until I got the feel i wanted from it.
Sanded it down and used a hot air gun to smooth the surface. I printed this with 10 top layers and 90% infill allowing me enough room to alter the mouthpiece with a blade until I got what I wanted. I've made this a wedge shape just to experiment with the idea.
I've designed it so that you get a different effect if you turn the mouthpiece 180 degrees. Have fun.

Wedge Screamer Trumpet Mouthpiece

grand piano box made in tinkercad :) print in pieces

9/5 - fixed files to be separate 

Piano Jewelry Box

grand piano box made in tinkercad :) print in 3 peices

grand piano box-4.stl

grand piano box-3.stl

grand piano box-2.stl

I made two types of guitars that can be used both as a pen holder and as a plant holder. 
There is also a bench that can be used as a pen hodler

Plant Holder + Pen Holder SK07

Plant Holder + Pen Holder SK07 1-3.stl

Music Equipment & Technology

Most Popular of All Time

Categories

Popular

Personalize

Trending