This is a front control panel cover replacement for a Commodore 1702 monitor. Other versions of this item I found online were slightly too long and had the hinges integrated, making them unprintable (no matter what they always broke). I rebuilt the entire model from scratch and made the hinges separated and keyed to the body pieces. This allows the hinges to be printed flat on the bed, giving them the strength required to not snap immediately. I printed this in PETG for increased flexibility. Glue the hinges in place with super glue (Gorillia GEL is the best for this IMO) and glue the center to each side of the body.   

Two versions of the left body are included, V2 has some extra support for the hinge although I did not need it when I printed mine.

Commodore 1702 Front Control Panel Cover

Left Body v2.stl

Here are some simple, easy to print stands for various hand held video game consoles. Included are:

Game Boy: Fit for DMG-01 (Original) Game Boy but also holds GBC, GBP etc. Also a good fit for Retroflag GPi Cases.

Game Gear: A THICCer version of above meant for the chonky Sega Game Gear. Might also hold a LYNX? Send me a free one and I'll let you know.

DS/PSP: For thinner consoles, holds my DSi, DS Lite and PSP just fine. (DS Lite not pictured).

Printed with 0.4 Nozzle at 0.28 layer height, lay the model on it's side.

Handheld Console Stands

Game Boy.stl

This is a Parametric Shelf Bracket that can be used in either a classic underneath the shelf style or as an over the shelf hanging down style bracket (see pics). The parameters that can be accessed in Fusion 360 are:

Board Thickness: How thick is the board you plan to put in the slot for use in the 'over' style. A lumber yard 1x6 will measure approximately 18.5mm by 140mm due to sanding and facing losses. Enter 19mm in this case for a snug fit around a 1x6.

Board Width: As above a 1x6 will measure approximately 140mm wide. A 1x8 would be 191mm etc. The supplied model fits a standard 1x6 at 140mm. 

Bracket Thickness: How thick do you want the perimeters of the bracket to be? I've chosen 5mm which works well. This measurement drives some other measurements  so tinker at your own risk.

Bracket Height: The length of the "other side" of the bracket when used as an overhanging bracket. Ideally this should be as close to the width of the board as possible given the available height of the bracket. 120mm for a 1x6 is a nice compromise for using in both directions. 

Please enjoy!

2-Way Parametric Shelf Bracket

Say Hello to your desk workstation's new best pal, Bendy McLampface!

Bendy is a #Gridfinity module with an articulated spine of connecting segments with an LED lamp inside! Bend, twist, pose and coil Bendy to whatever position suits you! Bendy can be as long or as short as you like, providing you have the wire and components to assemble him!

Bendy's internals consist of a salvaged USB micro cable, with the micro end cut off and the VCC and Ground wires connected via a SPST switch and a 100~ ohm resistor to any LED you please. 

I used a 3mm white LED but anything you can stuff down Bendy's throat will work great!

Once wired up glue the lid to the base and you're done. A magnetic base is highly recommended. 

Segments are printed with the flat 'female' end of the connector on the build plate. Support may or may not be required for the switch slot on the Lid depending on how well your printer can bridge.

Glue on Bendy's face to the bezel of the Lamp Shade (or don't Bendy will understand I'm sure).

Make sure to tie a knot in the usb cable to provide some strain relief, Bendy will thank you!

#Gridfinity Bendy McLampface

McLampface.stl

This is a collection of dust covers that slip over the bottom of cartridges for retro consoles. They are fit snug but come off easy (many iterations).

I printed these with Hello3D Marble PLA with an 0.8 nozzle because I can, but any filament should work and I'd love to see you print them in something flexible (I lack a direct drive extruder).

Consoles Included:
- Atari 2600
- NES
- SNES
- GB (Fits GBA as well)
- N64
- Master System
- Game Gear
- Genesis/Megadrive

These are what I own, but if you want something not listed send me a console and game to keep and I'll make it for you. ;)

Retro Game Cartridge Dust Covers

SNES.stl

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

These bit holders are parametric, a group of 9 bits will be generated for each module deep and wide selected. Values bitSize controls the bit shank (6.25mm or 4mm usually) and slopSize controls the extra 'space' around the holes. I find a value of 0.2 works well here.

If you lower the extrusion of the holes from 10 to 5 they work well for holding MK8 compatible hot end nozzels as well.

You can use the .f3d archive to edit the parameters as you choose. You can also go into the sketch and adjust the spacing directly, or edit the extrusion and choose if you would like the strain relief lines or not. I've uploaded some pictures of my customized ones as an example.

Source file included.

#Gridfinity Parametric Bit Holders

1x2 Bit Holder.stl

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman.

This is a 3x4 stepped paint shelf compatible with AK and Vallejo 24mm squeeze bottles.

UPDATE
Added requested sizes 1x4 and 3x5.

UPDATE

Added the source file and also a 3x3 version in STL. Increased the hole size slightly as it was a bit tight.

UP-UPDATE
One file was broken, it's fixed now. Also added a 2x3 version.

#Gridfinity Paint Shelf

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman.

This is a 3x4 stepped paint shelf compatible with AK and Vallejo 24mm squeeze bottles.

Paint Shelf 1x4.stl

Paint Shelf 2x3.stl

Paint Shelf 3x3 Fixed.stl

Paint Shelf 3x5.stl

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman.

This is a 1x1x1/2 module designed to hold the irregular shape of Gorilla brand super blue bottles. 

#Gridfinity Gorilla Super Glue Holder

This item is for use with the [#GridFinity system](https://www.youtube.com/watch?v=ra_9zU-mnl8) by Zach Freedman:

This 1x1x1/2 module holds one (1) bottle of 3D Gloop! [Nano Gloop](https://www.3dgloop.com/shop/nano-gloop), a really good glue available in a range of materials. The bottle is 25mm round and the hole is 25.5 with a chamfer.


#Gridfinity Nano Gloop

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

Hey There! Another #Gridfinity add-on! These parametric lids can be sized to any configuration you desire. Simply enter the slotsWide and slotsDeep numbers and like magic you have a lid for any basket or bin or whatever. 

A selection of common sizes in STL format included.

These should be printed with the top of the lid flat on the bed.

#Gridfinity Parametric Lids

2x2.stl

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

**UPDATE:**
Taking Zack's suggestion from his latest Gridfinity video, I have added a version (see attached Spacers 2.0.f3d) that not only adds a provision for keeping the magnet mounts in the corners but is also fully parametric up to 8x8. Thanks to KptnAutismus on github for the updated templates.


This is a collection of height adapting spacers for the Gridfinity system. You might ask "Why the heck would I ever need this?". The answer is relatively simple, while Gridfinity does an excellent job of maximizing your XY Axis storage space, you may want items at the back to sit at a higher level for accessibility, or maybe you want to stack something on top of two modules in your system but they are of different heights. My spacers will open up the world of the Z axis to your Gridfinity layout.

Sizes available are 1/4 (250), 1/2 (500) and 3/4 (750). Layouts available are:

1x1
1x2
1x3
1x4

2x2
2x3
2x4

3x3
3x3

4x4

Try it out today, spacers can go above or before your modules and consist of the outer perimeters of the Storage bin template.

Comment below if you need a custom size or height!

#Gridfinity Height Adaptive Spacers

2x2x025.stl

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

Say hello to the GFpi, a 2x2x3/4 Gridfinity module that holds a Raspberry Pi Model 4. Now your Gridfinity system can surf the world wide web! Front and side I/O slots give you access for all your cool peripherals and doo-dads. 

The Case is 3/4 of a unit high, enough to give space for 4 integrated standoffs and room for the height of the I/O. It is still stack-able should you desire it stay tuned for a series of stacking ring spacers for Gridfinity to let you convert odd size units to match up on heights!

Print with 0.4 nozzle as some walls are thin enough that larger sizes would not slice correctly. 

#Gridfinity Raspberry Pi Case

This is the Filacaster (Filament Caster), my 3d printed guitar in the classic American axe style. This is a new upload, because the old one got messed up when I was versioning and there were multiple copies of the same parts that I couldn't remove. 

This guitar is split into 9 elements to facilitate printing on most desktop FDM printers. The parts are referenced with 4.75mm printable layout pins and should be epoxied together. 

I would recommend adding some solid infill in your slicer around the tremelo block mounting points and printing the 3 center elements with a high infill (+50%) to increase strength. 

I have printed an earlier version of this guitar without the holes and while it does play, it is heavy, cumbersome without the tummy cut and probably not comparable to a real guitar in terms of intonation stability and the like. 

Since I printed the prototype, I've added the hexagonal holes, not so much as a design choice but as a way to reduce weight. I know this pattern is played out these days but I really did print the original in May 2021, before there were dozens of printed stratoclones all over the printer-verse.

A standard Strat style pickguard should fit, but I've included a two part guard that follows the hex cutouts and has some additional mounting holes.

Print with high infill, support from the bed. I printed the prototype with an 0.8 nozzle but I'm sure it would look even better with 0.4 and ironing enabled, time permitting.

When I print this newer version I will upload photos of it, in the meantime I added some pictures of the prototype without the holes. Please excuse the epoxy stains, I wasn't careful. :)

UPDATE

Forgot to add the slot for the selector switch to the bottom of the pick guard. Oops.

Filacaster

Fused.stl

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

This is a 4 unit wide by 1 unit deep by 1/4 unit high hook up wire spool holder. This is compatible with common wire hookup kits such as: [https://www.amazon.ca/CBAZYTM-Stranded-Gauge-Colors-Electrical/dp/B075M8DGYX/](url)

It will work with most common spool sizes, and uses a 6mm rod (as supplied with most kits). There are 6 threading holes at the front.

**UPDATE**

I added the source file as per request, but it isn't parametric so heads up.

_I removed the raised front panel as it was pushing the spools back too far, the holes are in the gridfinity body now._

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This was printed with Black eSun PLA PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support.

#Gridfinity Wire Spool Holder

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

This is a 4 unit wide by 1 unit deep by 1/4 unit high hook up wire spool holder. This is compatible with common wire hookup kits such as: [https://www.amazon.ca/CBAZYTM-Stranded-Gauge-Colors-Electrical/dp/B075M8DGYX/](url)

It will work with most common spool sizes, and uses a 6mm rod (as supplied with most kits). There are 6 threading holes at the front.

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support.

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

**UPDATE**
_Hole sizes increased by 0.2mm to allow better tolerance._

 A 1 wide by 2 deep by 2 unit high Standard Sharpie holder MAXIMIZED to hold an outstanding 14 Sharpies or other 12mm cylindrical items. The wells are 65mm deep. Also available in a pathetic 1x1 version holding a meager 5 items.

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This was printed with black eSun PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. 

#Gridfinity Sharpie Holders

1x2x2 Sharpie.stl

This item is for use with the #GridFinity system by Zach Freedman:

https://www.youtube.com/watch?v=ra_9zU-mnl8

A 1 wide by 1 deep by 1/2 unit high "Generic Building Brick" adapter plate for Gridfinity. Proudly display all your special brand-agnostic little guys in the midst of all your gubbins and paraphernalia.

This was printed with an 0.4 nozzle, I'm not sure it is advisable to print with larger ones due to the extreme precision required for brick-and-stud blocks to correctly seat. Printing studs like these is a difficult task, and no 3d printers will have the same extrusion widths. Included are .STL files with the studs set to the proper 4.8mm size and also the 5.05(!) I had to export for my under extruding machine to make something snap-able. Also included is the Fusion 360 archive, edit the sketch Studs and change the top left stud diameter and the rest will follow as they are an array. A 1x2 test plate archive is also included so you can dial in the stud size without wasting filament.

Results may vary, [Blacktron](https://brickipedia.fandom.com/wiki/Blacktron_Astronaut) Pilot not included.

#Gridfinity Toy Brick Adapter

1x1x2 Brick Adapter 4-80mm Stud.stl

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

 A 1 wide by 2 deep by 1/2 unit high USB thumb drive and SD card holder for use on a weighted base plate. 

**UPDATE 2**

_As requested, I've added a USB only version with 8 slots to the archive. Please note they are angled due to the fact that the bodies of most USB drives are too wide to fit 2 columns/rows in parallel._

**UPDATE**
_I've added three additional STL files, one with a double height 10x Standard SD card version which is stack-able, a single height 10x Standard SD card version which is not and a half height 16x Micro SD card version which is stack-able. Please note that due to the depth required for the micro SD card and to keep the bin at half height the slots intersect with the screw holes on the bottom of the bin. You will be able to use magnets but not m3 screws._
 
Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This item was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The holder has slots for 4 USB Devices, 6 Standard SD cards and 6 Micro SD cards. The Standard slots are capable of holding 2 Memory Stick Duo's for all you PSP fans and even xD cards for you retro Fujifilm camera users. Tolerances are loose to allow the model to be printed easier on poorly configured printers that over extrude.

#Gridfinity Usb and SD Card Holder 

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

 A 1 wide by 2 deep by 1/2 unit high USB thumb drive and SD card holder on a weighted base plate. 
 
Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. This item was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The holder has slots for 4 USB Devices, 6 Standard SD cards and 6 Micro SD cards. The Standard slots are capable of holding 2 Memory Stick Duo's for all you PSP fans and even xD cards for you retro Fujifilm camera users. Tolerances are loose to allow the model to be printed easier on poorly configured printers that over extrude.

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

**UPDATE 4**
Added 3x5x2 and 3x5x1 as per request. Since I've been accused of being un-intellegent (yes hyphenated) in the comments I've resolved never to add a readme file to any of my models. You'll just have to remember where you downloaded them.

**UPDATE 3**

As per request, added 1x4x1, 1x4x2, 1x5,1 1x5x2.

**UPDATE 2**

More new sizes, as per request. Also added the source file, though I'm not sure anyone will understand my crude methods.

**2x3x1**
**2x3x2**

**2x4x1**
**2x4x2**

**2x5x1**
**2x5x2**


**UPDATE**

 A set of Gridfinity baskets with a hex mesh grid. Multiple sizes now include (WxDxH):

**1x1x1**
**1x2x1**
**1x3x1**

**1x1x2**
**1x2x2**
**1x3x2**

**2x2x1**
**2x2x2**



Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The basket is slightly spongy and flexible. Remove any stringing with a heat gun or lighter.

#Gridfinity UPDATED 5/20/22! Hex Baskets

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

 A 2 wide by 2 deep by 2 unit high basket with a hex mesh grid. I use this to store about 25 misc pens on a weighted base plate. 

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The basket is slightly spongy and flexible.

#Gridfinity 2x2x2 Hex Basket

Hi, my name is Bristien and I make things. All sorts of things really.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

bigbrisco