Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3955039.

Run 10x15 Cable Chain on the Y axis movement for X axis cabling.

Ender 5 X Axis Cabling, Y Axis Movement Cable Chain Adapters

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4015038.

Better mount for self aligning when using my Shaft Supports.
Print in something very strong. I am using HTPLA from Proto-pasta that has been heat-treated.

Ender 5 Y-Axis Stepper Motor Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3774993.

Replace the cheezy brass ferrule (will likely need new belts) with these. Print 4 of them.
Install then feed belt thru from bottom and secure with 2 m3 x 12 shcs and 2 m3 nuts. 
Update! 7-28-2019
Significantly reduced size, only need 2 screws per. Added nut pockets.

Ender 5 Y axis belt clamp and aligner

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3976851.

Simple, can be bolted to End of extrusion but you need to tap. M5 Bolt Hole. Keeps the 6mm belt from rubbing the extrusion. Meant to work with 20t 2gt belt pulleys, not the flange bearings.
Print the Cap at 0.2 with curved part facing down.
Print the bolt at 0.12 as shown in pic. It works well enough for what this is.

V3, updated to allow more side to side offset of belt without allowing it to hit the 2020 still.

2020 End Cap with 6mm Belt Guide

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3983422.

Perfectly aligns and supports the shaft drive on the Y axis. Without this there was no way for me to be sure it was aligned perfectly. Also puts a bearing on the other side of each pulley. Use 2 minimum, or 4 if you want to be a little crazy and play with getting stepper aligned perfectly. I replaced the coupler and also drilled out the stepper mounting holes so I could let this all self-align with 4x of these brackets. Will need 2 M5x10 SHCS and a 2 t-nuts each. Uses the same F688 bearing as the OEM brackets. Tight fit if your printer is tuned. I printed .2mm layer, 50% infill.

Ender 5 Y-Axis Drive Support Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5202633.

Print in ABS with high infill. PETG or CF PLA will probably work as well. Sizes of components and spacers are important. Order of stacking is shown in one of the jpg's.
Uses heatset inserts M3 x 5 (d) x 4
4x M3x22
4x M3x30

Ender 5 Z axis thrust bearing block

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3974745.

For the X axis of an Ender 5. Installs without modification
Gets Belts correctly aligned for the 20t 2GT pulley, down in the 2020 extrusion.
Also includes BLTouch mounting option with spacers.
Uses 4x M3x20 SHCS plus 4x M3 Nuts
Made with PETG 0.2 layer height 0.4 nozzle
Print with supports touch build-plate for the bases.

Ender 5 X Axis belt clamp and aligner plus BLTouch mounting

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3934176.

Made to mount on 2040. Moved holes to be 20mm apart

Reverse Bowden Adapter for 2040

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4084481.

Just puts a nice cover over the switch, purely cosmetic.

Creality Switch Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3550210.

Used to space the ESC plus provides wire guides. Wire diameter should be around 1.8mm.


Tekko32 F3 Metal ESC Wire Guides

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4079436.

Make yourself a cleaning system for your nozzle.

Mounts to the front 2020 extrusion.

Use brass brushes from Harbor Freight with the handle cut off.

I use this on my startup G-code
G12 P1 S2 T3

My firmware setting in Marlin 2.0
#define NOZZLE_CLEAN_FEATURE

#if ENABLED(NOZZLE_CLEAN_FEATURE)
  // Default number of pattern repetitions
  #define NOZZLE_CLEAN_STROKES  2

  // Default number of triangles
  #define NOZZLE_CLEAN_TRIANGLES  3

  // Specify positions as { X, Y, Z }
  #define NOZZLE_CLEAN_START_POINT { 235, 55, (Z_MIN_POS + 5) }
  #define NOZZLE_CLEAN_END_POINT   { 240, 8, (Z_MIN_POS + 5) }

Ender 5 Nozzle Cleaning Station

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4460189.

Superior bearing block, eliminated concentricity errors. As long as your screw is straight you should have no wobble. Requires some bearings and stuff that i will be updating this summary with a BOM soon.

You must invert the nut, which is the right thing to do regardless, so that the weight of the bed is NOT compressing the spring, or you will lose Z capacity.

2x F688 Bearings
Spider or spring type coupler max length overall 30mm
Thrust bearing
Shaft Collar
Spacer, recommended 0.5mm thick, change Z to suit your setup.


Ender 5 Z axis leadscrew bearing block

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4944105.

Fits the ADAFRUIT version

ADXL345 clip on Voron Dragon

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4967305.

Positions x axis switch to allow MGN12 carriage to home. Works with the XChange system

Ender 3 Pro XChange X Axis Switch Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4009551.

Mounts the X axis end stop in proper location to hit the metal frame instead of the wheel. Can be combined with my switch cover, check it out.

Ender 5 X-Axis End Stop Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4966010.

Original part had modeling errors. I remodeled it to correct issues particularly with the bosses.
Also made it to allow the M2 screws to supplement the PCB mounted switches.

Voron 2.4 X Y endstop pcb mount, corrected

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4785824.

11mm for Mosquito and 30mm for Copperhead.
I print in Carbon Fiber HTPLA.
Use a single edge safety razor to cut.

Bondtech LGX Plus Mosquito or Copperhead PTFE cutting guides

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3694056.

I found some models on here of the Ender 5 X Axis carriage but they were not accurate to the one on my printer. I disassembled, measured and updated the model to reflect the correct dimensions.

Ender 5 X Axis Carriage, Accurate, Measured

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3559922.

Tight fit, put slim foam under your Rxsr and use a zip tie and a small strip of foam on top of receiver.

R-XSR 20mm mount with Antenna Tubes

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4232556.

I made my own tubing cutter fixture. Major change is much more support for the razor blade to keep it cutting straight. I could not get perfect square cuts on the original.

Remix Hotend Fix Tubing Cutter Tool

Stabilizes the Z axis lead screw with proper thrust bearing and axial bearings on each side. Takes load completely off the stepper.

michael.r.gamber