AllAll
Search scope
Upload for Search
AllAll
Search scope
Upload for Search
J

Left Vent Mount - MK7 / MK7.5 Golf

by
jeoje
Follow
Follow
Remix Model
Social
J
jeoje
|
Image 5 of 15
Left Vent Mount - MK7 / MK7.5 Golf 3d model
J
jeoje
|
Image 5 of 15
Left Vent Mount - MK7 / MK7.5 Golf 3d model
2D
3D
Makes
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf 3d model
Left Vent Mount - MK7 / MK7.5 Golf - I used strategically placed zip ties to hold it on because I wasn't able to get any tapes to stick to the PETG. Printed with Prusament PETG on the Prusa Mini. 100% infill for rigidity. Took 2 hours and 30 minutes. No supports. 5mm brim to make sure it stuck to the build plate. Using a Scosche Magicmount Magnetic dash mount to hold the Accessport. Have yet to run the wire. I plan on running it through the vent that this clips too. I will be reprinting this using ASA to make sure it doesn't warp during the summer or while cranking the heat during the winter. - 3d model
Left Vent Mount - MK7 / MK7.5 Golf - Printed with Prusament PETG on the Prusa Mini. 100% infill for rigidity. Took 2 hours and 30 minutes. No supports. 5mm brim to make sure it stuck to the build plate. Using a Scosche Magicmount Magnetic dash mount to hold the Accessport. Have yet to run the wire. I plan on running it through the vent that this clips too. I will be reprinting this using ASA to make sure it doesn't warp during the summer or while cranking the heat during the winter. - 3d model
Left Vent Mount - MK7 / MK7.5 Golf - I used strategically placed zip ties to hold it on because I wasn't able to get any tapes to stick to the PETG. Printed with Prusament PETG on the Prusa Mini. 100% infill for rigidity. Took 2 hours and 30 minutes. No supports. 5mm brim to make sure it stuck to the build plate. Using a Scosche Magicmount Magnetic dash mount to hold the Accessport. Have yet to run the wire. I plan on running it through the vent that this clips too. I will be reprinting this using ASA to make sure it doesn't warp during the summer or while cranking the heat during the winter. - 3d model
This model is restricted by licensing terms. 
View license.

Description I made this specifically for mounting a Cobb Accessport, but really you could attach anything to this.

Install Clips in above the left vent trim, and uses VHB tape to secure the bottom to the bottom of the vent. You should be able to move the mount left or right the width of the vent without too much issue.

VHB tape the ram ball that comes with the Accessport to the mount. Use the cable stay to keep the cable from flopping around.

Material ABS is suggested, PETG would probably work, but I would not suggest PLA as it will warp in the heat. MatterHackers Midnight Blue ABS is what was used for the pictures. I will reprint in black or graphite gray ABS when more comes in.

Settings Walls: 4 Bottom: 5 Top: 5 Infill: 40%

Category:

Hobbies
Automotive
4 Likes24 DownloadsNovember 15, 2021
4 Likes24 DownloadsNovember 15, 2021
This model is restricted by licensing terms. 
View license.
TermsTerms & ConditionsSupportFeedbackReportReport ModelPrivacy