The Corsair H150 AIO cooler has a cosmetic pump cover that displays the Corsair logo and it is attached magnetically so that it can be rotated in order to let the logo be upright with any pump orientation. This also works with the H55 and H100 models, which share the same heatsink/pump assembly.

You can unscrew the four screws on the back of this cover to take it apart and i thought i could recreate it to print my own logo. 

The dimensions I designed take into account my own printer tolerances. I went through some trial-and error, you might need to adjust the diameters of the little pillars the screws attach to, but it's a small part and prints in _minutes_, so you can really fine-tune it if you want.

There are two ways you can have the RGB light shine through your logo: you can either print this part flat, in white/translucent plastic and paint the negative space in black to block the light, or you can include your logo in the design with your software of choice (I used F360 so I included a fully modifiable .step file) then print the face in black plastic and the rest of the cover in white, after a few solid layers. 

The first option is best for detail, but you'll have to resort to some kind of screen printing if you want to achieve factory-level precision and light blackout. The latter takes a little trial and error, and it requires you to print the logo face-down, which depending on the gauge of your printer, nozzle, bed calibration, etc.. it might lose some detail. YMMV. 

To print my own design I first extruded the text -1 mm into the surface of the part, then I printed it face down on my Bambu Labs P1S with a .6 mm nozzle and 0.18 mm layer height, no supports, 100% concentric infill (for maximum light blockage, some kind of infill pattern might look good if light shines through the part though). 

I added an automatic pause at layer 4 and manually switched filaments from black ABS to white, as i do not own an AMS. AMS users might achieve good results by printing this upright, tilted and supported on its back side to maximise print detail but increasing waste and print time. 

Corsair H150 AIO custom logo pump cover.

your logo here.stl

This multitool holder was designed for my tools specifically, so mine fit perfectly, but I included the .step file in case you need to modify it. It prints in place, all at once with no supports on my Bambu Lab P1S.

The vertical openings are designed to hold three pairs of scissors (for cloth, pinking shears, paper), while the tilted slots allow for a snug fit for your thread snips, tiny scissors and tweezers. The weight of the scissors keeps it stable, you don't need to weigh it.
It can hold a few bobbins on the front and in the back.

I use a Koh-I-Noor Hardtmuth chalk for my projects so the ridges below should hold it perfectly and the square opening on the right is used for the little case that holds spare chalk.
I cut a kitchen sponge a little bit bigger than the shallow square on the left and press fit it snugly, rough side down, to use it as a pin cushion.

The circular opening on the left size holds a 10mm round neodymium magnet, which can hold needles and small items.
I usually use the tall ridge all around to keep a few easily accessible clips, which I prefer over pins. 

Overall, it's designed to hold:

- 8in fabric scissors
- 8in pinking shears
- 8in scissors (normal/paper)
- 1in scissors
- Singer seam ripper
- Thread snippers
- Tweezers
- DIY pin cushion
- 1-4 Needles (on the neodymium magnet)
- Approx 10 bobbins
- 2x Koh-I-Noor Hardtmuth chalk holders
- Koh-I-Noor Hardtmuth spare chalk case
- Roll-up measuring tape or 45mm rotary cutter blades
- 10-20 small sewing clips
- Various small items

Sewing tools holder

Body11.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

giacomo1574

Achievements

Seedling

Corsair H150 AIO custom logo pump cover.

Sewing tools holder