This plan is for anyone from personal use to commercial for physical prints.
With this plan you get full access to my files with no download restrictions so take what you like and happy printing!

Micro's Emporium

Pegs:
This peg is used to connect different modules together. I recommend printing a bunch of these and just setting them to the side and using as needed.

Hardware needed:
None

Instructions for Printing:
Raft = no
Brim = optional but not needed
Wall Loops/Top and Bottom shells  = 2 - 4 (personally i like 4 for extra stability)
Layer Height = 0.2 mm
Speed = Default
Temperature = Default for your material of choice
Orientation = One of the flat sides. This makes it so there is less resistance when inserting and makes it so if things do get stuck, the sheer point will happen on the peg instead of the module.

During testing I used the Bambu Labs x1 Carbon with PolyLight PLA and left most settings in the Bambu Studio as default with any changes listed above so your print times may vary.

Material = roughly 3 grams
Time = 23 minutes
Material and time includes the Bambu X1 Carbon prep time and flow lines.

I recommend printing a full build plate worth, for me I print about 50 at a time and put them in a bag for later use. I have added this as an optional file.

Peg X 50:
Material = roughly 88 grams
Time = 3 hours 20 minutes
Material and time includes the Bambu X1 Carbon prep time and flow lines.


Arduino Module Peg.stl

Arduino Uno:
This Module is used for the Arduino Uno microprocessor.

Hardware needed:
2 x 2 mm screws with 4 mm of length
Arduino Uno

Instructions for Printing:
Raft = no
Brim = optional but not needed
Wall Loops/Top and Bottom shells  = 2 - 4 (personally i like 4 for extra stability)
Layer Height = 0.2 mm
Speed = Default
Temperature = Default for your material of choice

During testing I used the Bambu Labs x1 Carbon with PolyLight PLA and left most settings in the Bambu Studio as default with any changes listed above so your print times may vary.

Material = roughly 90 grams
Time = 2 hours 34 minutes
Material and time includes the Bambu X1 Carbon prep time and flow lines.

Instructions for use:

Use the screws to thread the holes inside the module by screwing them in and then removing them.
Insert the Arduino Mega into the hole with the ports sticking out of the holes in the side at an angle and then sliding it down until it is flat. By doing this the holes in the arduino should slide into place over the little pegs sticking up.
Insert the 2x screws into the holes in with no pegs and screw into place until they won’t go down very far.  (Warning: do not over tighten or you risk harming your Arduino)


Arduino Module Uno.stl

Arduino Mega:

This Module is used for the Arduino Mega microprocessor.

Hardware needed:
2 x 2 mm screws with 4 mm of length
Arduino Mega

Instructions for Printing:
Raft = no
Brim = optional but not needed
Wall Loops/Top and Bottom shells  = 2 - 4 (personally i like 4 for extra stability)
Layer Height = 0.2 mm
Speed = Default
Temperature = Default for your material of choice

During testing I used the Bambu Labs x1 Carbon with PolyLight PLA and left most settings in the Bambu Studio as default with any changes listed above so your print times may vary.

Material = roughly 87 grams
Time = 2 hours 32 minutes
Material and time includes the Bambu X1 Carbon prep time and flow lines.

Instructions for use:

Use the screws to thread the holes inside the module by screwing them in and then removing them.
Insert the Arduino Mega into the hole with the ports sticking out of the holes in the side at an angle and then sliding it down until it is flat. By doing this the holes in the arduino should slide into place over the little pegs sticking up.
Insert the 2x screws into the holes with no pegs and screw into place until tight. (Warning: do not over tighten or you risk harming your Arduino)


Arduino Module Mega.stl

Hello,
My name is Jon but you can call me Micro.

I am a hobbyist designer who wants to find ways to push technology as a whole forward and to me that means starting with hobbyists of different types.

I am trying to design and post a project at least once a month likely towards the end of the month.

I like to design things as modular as possible so you can create your own work flow. Not all projects will be modular between each other but in their own ecosystems.

Right now all my designs are behind a paywall but I will also be posting basic versions that are free to use.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

MicrosEmporium

Achievements

Seedling