Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1240754.

It's finally here. The new FPV-Rover V2.0 https://www.thingiverse.com/thing:2952852

This is a remix of the drogerdy designed by timmiclark. http://www.thingiverse.com/thing:700835/#files

Upgrade 01: http://www.thingiverse.com/thing:1269962 Upgrade 02: http://www.thingiverse.com/thing:1700138 Upgrade 03: http://www.thingiverse.com/thing:1936491 Upgrade 04 by Superfly851: http://www.thingiverse.com/thing:1979227 Upgrade 05(Nerf Dart Launcher): https://www.thingiverse.com/thing:3835285 Videos on Youtube https://www.youtube.com/watch?v=4Qc0D7U5R0s https://www.youtube.com/watch?v=6tj8FTdTix0 https://www.youtube.com/watch?v=TQPVS7V3_Jw https://www.youtube.com/watch?v=x7D1qESYsrA https://www.youtube.com/watch?v=jhvpuBi0zO4 https://www.youtube.com/watch?v=lbQW_ebiLKA https://www.youtube.com/watch?v=BlgNhrQPaEA https://youtu.be/AgPFbaMxf3g

<b>Instructions:</b>

Body: The body has a support on the bottom to become a clean print. The support has to be removed after printing. Infill: 15%

Track: You'll need 64 tracks. Infill: 15%

Pin: There are two different pins. The normal one is 3.7mm. If the chain is to tight, you should print the small one with 3.0mm and add 3-4 of those pins. After printing the pins, you have to remove the small support on each side. Infill: 15%-20%

Small cog: You need 8 small cogs. Infill: 15%

Main cog: You need 4 main cogs. Infill: For the first 10mm you can print it with 15%. For the rest you should use at least 90%.

Rubbertrack: Use Flexifil or Ninjaflex for the rubber track and glue it to the track. The rubber tracks are not necessary but you will love it. Infill: 30%-50%

Track2: If you don't want to print the rubber track or don't have Ninjaflex, you can print track2 instead of track + rubber track. Infill: 15%

Front + back: Print this with brim if it doesn't stick to the surface and use support structure. Infill: 15%

FPV-Cam holder: Print it with support structure and glue the small part on the back side. This is for the servo to move the cam up and down. Infill: 15%

Camera and LED mount: You need these two parts if you want do use a fpv-camera. Infill: 15%

Tow-bar: Infill: 15%

Tow-bar plug: If you don't want to use the tow-bar you need this twice. Infill: 15%

LED-mount: Infill: 15%

Top: The top is designed to use a 40mm fan for cooling the vtx and to plug in the fpv-antenna from banggood. Infill: 15%

Track-body-connector: You can glue the track frame together and glue it to the body but if you do that, you can't replace parts if broken. Use this to mount the track frame to the body. They are marked for front and back. Infill: 15%

Track outer cover: Print this part twice. Infill: 15%

Outer track frame: Print this part twice. Infill: 15%

Inner track frame right/left. Infill: 15%

<b>Parts to print:</b>

1x body (for 2S or 3S) 1x front 1x back 64x track 64x rubber track 64x pins (try which one fits best for you) 8x small cog 4x main cog 1x inner track frame right 1x inner track frame left 2x outer track frame 2x track outer cover 1x top 1x set track-body-connector 1x tow-bar 2x tow-bar plug 1x fpv-cam-holder 1x set camera-led-mount 1x led mount

<b>Parts you need (BOM):</b>

2x package of 10 bearings 688ZZ for the small cog (you need 2 bearings each cog) https://bit.ly/3F3ZmLg

4x motor with gear (you need 4 motors, 2 for each chain) http://bit.ly/3Bb6YKQ

2x brushed esc (one esc for each side. connect two motors to one) https://bit.ly/3ivkvXj

8x bearings 61802 2RS / 6802zz for the main cog (each main cog needs 2 bearings) http://bit.ly/2wyk0QX

1x Front camera https://bit.ly/3H8Z60v

1x Rear camera http://bit.ly/3XGh3Zc (8mm x 8mm or 12mm x 12mm)

1x FPV-switch http://bit.ly/3uJdCog

1x Package magnets 3mm x 1mm (front and back are sticked to the frame by magnets) http://bit.ly/3uq9skU

1x fan 40mm (12v) for cooling the vtx http://bit.ly/3BgRS6H

1x servo for the tilt-mechanism for the cam and LED https://bit.ly/3VR58Xu

We use 4 tuning motors (Slotdevil 2035) instead of the motors which come with the gear reducer. You can run the tuning motors with 3S (the ESC does supply this, even if they are for 7,4v)

Use 4 motor pinions for the tuning motors (sigma 4 9z m50 nylon)

20x M3 Screw 25mm long https://bit.ly/3izqOcy 4x M4 Screw 20mm long https://bit.ly/3iAtgiW 4x M4 Nuts https://bit.ly/3B7QiE1