.jpg&w=3840&q=75)
AVAILABLE FOR COMMERCIAL RESALE WITH TIER 2 - V2 FRAME ONLY
This model is more simplistic in color design to benefit those with one or no AMS unit while still producing a high quality traditional Japanese style piece.. AMS/MMU not needed. Manual filament swaps can easily be done with pauses. This model will only be available to club members.
I have included 2 different 3MF files for Bambu Studio. Please read all the instructions carefully.
For 1 AMS - There are 6 different colors in this model and no colors repeat so it will be pretty easy to print on 1 or NO AMS. For 1 AMS assign colors 5 & 6 to AMS slots 1 & 2. Follow the “pro tip” below if you are worried about missing your color swaps or just remove colors 1 & 2 when color 3 starts printing and replace them with 5 & 6 respectively.
For 2 AMS units - Just load the 6 colors in order, assign accordingly and print.
For NO AMS - pauses already set (manual color changes). Just go in the order below.
Pro Tip: If you are using more colors than you have AMS units you can manually unload the last spool after the print starts. This will force a pause when this spool is eventually called up for duty. The pause will be forced if any spool is not present when called for so in this case you can just un-feed spool 8, swap out the brown/blue gray [see chart below] when the pause occurs then re-feed color 8 [slot 8] back in and resume. With different models it may make sense to force the pause in other AMS slot[s] depending on the color swap order.
If you do not have Bambu Studio/Orca I recommend using it to look through the settings and copying them to make a Hueforge profile template for yourself in your slicer of choice so that future prints will be quick.
If you have any questions about printing this hit me up.
AMS SLOT GUIDE: The model colors will go in and be assigned to the following slots depending how many AMS units you have.
MODEL COLOR - [1] [2] [3] [4] [5] [6]
1 AMS - SLOT ---- [1] [2] [3] [4] [1] [2]
2 AMS - SLOT ---- [1] [2] [3] [4] [5] [6]
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. The profiles have a height modifier to print the first 0.64mm @ 0.16 layer height as that is the min depth/non blended portion of the base color. If you use a different slicer set all your color changes before doing the modifier as it changes the amount of layers. This shaves off approximately half an hour of print time. As with all Hueforges if you scale the model DO NOT change the Z dimension. If you substitute filaments results will vary. If you have Hueforge you can import the STL and see how substituted filaments will change the outcome before printing. If you have questions hit me up.
I use the TD-1 to measure my filament opacity which is why you see the names I have assigned to them in Hueforge. This gives me an accurate prediction. Filament TD can vary from brand to brand and even from spool to spool. If you want to measure you own for accurate predictions in Hueforge check out MY WEBSITE where I have official TD-1 units for sale.
Filaments Used: PLA BambuLab Matte Charcoal Transmission Distance: 0.6 PLA BambuLab TD-1 Blue Gray Transmission Distance: 3.1 PLA Polylite TD-1 Blue Transmission Distance: 1.6 PLA Bambu Lab PURPLE Transmission Distance: 5 PLA BambuLab TD-1 Pink Transmission Distance: 5.8 PLA BambuLab Tough TD-1 Cream White Transmission Distance: 8.3
(This is a high TD white. Polysonic White PLA by Polymaker or Creality Hyper White are good substitutes)
This print uses 6 unique filaments
Swap Instructions: Start with Charcoal At layer #12 (1.04mm) swap to TD-1 Blue Gray At layer #13 (1.12mm) swap to TD-1 Blue At layer #17 (1.44mm) swap to PURPLE At layer #20 (1.68mm) swap to TD-1 Pink At layer #23 (1.92mm) swap to TD-1 Cream White for the rest.