Profile Image
Bedlam Threadz
Bedlam Threadz

Bedlam Threadz

Follow

Select a membership plan

Model is included in this plan
Available now

Supporter Tier
$10.00
/ month

This tier is for people that enjoy my work and would like to support my ongoing efforts to make high quality models.

This tier allows access to all models that will be both exclusive and early access before public release. Models will be labeled accordingly and all early access models will be a minimum of 60 days prior to public general release. Some models will never be released outside of subscription tiers. This tier does NOT allow for commercial use of designated models. Personal use only. You may download and print these models, but may not sell prints or files and will not distribute any files in any manner.

Model is included in this plan
Available now

Commercial Tier
$15.00
/ month

This tier is for people that are looking to resell printed models that are specifically designated for physical good sales. To resell printed models you must have an active subscription. If you choose to stop subscribing your rights to resell printed models ends as soon as your paid period expires.

Redistribution and resale of the digital files is not allowed, and subscribers acknowledge that Bedlam Threadz has the sole right to distribute, post and sell the digital files provided.

This tier also provides for the ability to request specific models to be created. For requests under this tier models via request will be available to all club members. If you would like a private custom design you can always message me and we can work something out if you would like to retain the rights to specific artwork.

Bedlam Threadz
Bedlam Threadz

Hueforge Magnet Frame - 100x100

by
Bedlam Threadz
Bedlam Threadz
Bedlam Threadz
Bedlam Threadz
|
Image 1 of 2
Hueforge Magnet Frame - 100x100  3d model
Bedlam Threadz
Bedlam Threadz
|
Image 1 of 2
Hueforge Magnet Frame - 100x100  3d model
2D
3D
Makes
Hueforge Magnet Frame - 100x100  3d model
Hueforge Magnet Frame - 100x100  3d model

Hueforge Magnet Frame - 100x100

This is a Hueforge frame with 8 holes for 6x3mm magnets at the back for 100x100 (technically 108x108 read below) filament paintings. I have included two frames in this pack as the tolerance of the magnets I ordered varied a bit. One has holes that are 6.2mm and one has holes that are 6.3mm. I found that 4 magnets in the corners held really well on my fridge, but they are “rare earth magnets” so they may be stronger than some that others have hence the extra holes if needed.

This model works like the 200x200 V2 larger frame in that the paintings are actually 108x108 after a 108x108x0.64mm plate is merged to the 100x100 Hueforge model. This allows the entire picture to be displayed within the frame and in this case allows for the frame to have a slimmer profile.

Instructions:

Painting

Right click your build plate and add a primitive cube.

Non-uniform scale the cube to 108x108x0.64* (0.64 in my case. This should be equal to your “min depth” setting in Hueforge)

Import your 100x100 Hueforge Model

Center both the model and the primitive cube.

Merge/Assemble the two models.

Print with your trusty Hueforge profile and you should be good to go.

Frame

I printed it using the standard 0.2 Bambu profile which was 0.2mm layer height/15% grid infill and and two wall loops. You can cut a portion of the frame with the holes in the slicer if you want to test your magnets in the different hole sizes. It might be worth putting a negative modifier cylinder all the way through the hole so you can pop it out easily. I had to hammer in the one with the 6.2mm holes and the ones with 6.3 were a little loose so I used some gorilla glue and let them set over night. I would recommend cutting the end off of a Q-tip and use it to apply the glue inside the holes very sparingly.

If you have any questions hit me up.


0 Likes0 DownloadsJuly 14, 2024
This model is restricted by licensing terms.