Demon Slayer Sabito Mask for Decor or Cosplay.

3D printing settings used:
Bambu Slicer 0.16mm standard setting
Size: 175 x 97 x 247 mmm
Suggestion: I print the mask standing up so the layer lines end up at the bottom vs if you lay it flat with supports on the inside of the mask (you'll have layer lines on the middle of the forehead and middle of cheeks which will be visible when worn).

For the eyes I paused my print midway (see photo or use 3mf file) and added tulle fabric and resumed the print, this way the tulle was imbedded in the eye print.

The scar has sparse infill of 30% since the spikes can be fragile when removing supports. Suggestion orient it the way as show in photo above (if you use the 3mf file for bambu all settings and orientations are already set).

Mask and pink ears have a sparse infill of 8%.

Everything else is set to 15% sparse infill.

Demon Slayer Mask - Sabito

Sabito.3mf

Ear pink L.stl

Ear pink R.stl

Eye L.stl

Eye R.stl

Head Cosplay 1.stl

mouth.stl

Pupil L .stl

Pupil L (1).stl

Pupil R .stl

Pupil R (1).stl

Scar.stl

Yiga Clan Mask as seen in the TOTK game ;)

Used Bambu slicer at 0.16mm Optimal setting.

Adding a photo of how the eyes were oriented and where they were paused to allow you to add the tulle fabric.

When orienting the eye triangles lift the inner corner after you use the "auto orient" option on Bambu Slicer. The key is to try to make the top surface as flat as possible (see photo) so you can lay your tulle down flat-ish This is ONLY APPLICABLE IF you are not using the 3mf file provided. The 3mf file is already oriented fine w/ the pauses added.

The Legend of Zelda, Tears of The Kingdom Yiga Clan Mask

yiga.3mf

circle.stl

earring bottom L.stl

earring bottom R.stl

earring red L.stl

earring red R.stl

earring top L.stl

earring top R.stl

eye.stl

left eye triangle.stl

left triangle.stl

middle triangle.stl

right eye triangle.stl

right triangle.stl

Demon Slayer Hotaru & Kozo Masks modeled in Blender.
Adding 3mf file ready to print and separate stls too.
Scale down eyes to 99% and you will be fine.
For the eyes I paused my print (see photos) and added tulle fabric and secured it with magnets and resumed the print, this way the tulle was imbedded in the eye print. To remove outside tulle just cut it off as close to eye with exacto knife and torch excess away. When glued into mask it wont be visible.(All orientations and pauses included in 3mf file)

Demon Slayer Swordsmith's Maks - Hotaru & Kozo

Hotaru.3mf

HotaruFace1.stl

HotaruEyeR.stl

HotaruEyeL.stl

HotaruEyeBrowL.stl

HotaruEyeBrowR.stl

Kozo.3mf

Kozo Face 1.stl

KozoCheek L.stl

KozoCheek R.stl

KozoEye L.stl

KozoEye R.stl

KozoEyebrow L .stl

KozoEyebrow R.stl

Mech-E/Otaku with a passion for 3D printing.


Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

AllTheBuz3D

Achievements

Seedling