Profile Image
3DGeex
3DGeex

3DGeex

Hi!

My name is Michael, I'm a Scifi, Gaming and Science Geek and I looove 3D printing! Recently I started to design my own models and turn my ideas into printable stuff! There is really no specific style to my models - From practical to funny and articulating things! Here I will share my designs with you and would also love to hear ideas from you! Thank you for your support!

Michael - 3DGeex

Follow

Select a membership plan

Model is included in this plan
Available now

Personal Geek
$7.00
/ month

Personal Geek Plan:

  • 8 Downloads every month from the entire catalog.
  • Access to exclusive members only models.
  • Early access to models before they are released on other platforms.
  • Discord access where you can propose ideas, provide feedback, participate in polls and general discussions.

Model is included in this plan
Available now

Commercial Geek
$10.00
/ month

Commercial Geek Plan:

  • 12 Downloads every month from the entire catalog
  • Commercial license allowing you to sell physical prints
  • Access to exclusive models available only for members
  • Early access to models before they are released on other platforms
  • Discord access where you can propose ideas, provide feedback, participate in polls and general discussions.
  • I will publish your online store as an authorized seller on my social media accounts which can bring you more traffic and sales

Model is included in this plan
Available now

Super Geek
$12.00
/ month

Super Geek Plan:

  • 20 Downloads each month from the entire catalog
  • Access to exclusive models available only for members
  • Early access to models before they are released on other platforms
  • Commercial license allowing you to sell physical prints
  • Discord access where you can propose ideas, provide feedback, participate in polls and general discussions
  • I will publish your online store as an authorized seller on my social media accounts which can bring you more traffic and sales
Michael T

The Grinch Middle Finger

by
3DGeex
Follow
Follow
Remix Model
3DGeex
3DGeex
|
Image 1 of 9
The Grinch Middle Finger 3d model
3DGeex
3DGeex
|
Image 1 of 9
The Grinch Middle Finger 3d model
2D
3D
Makes
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model
The Grinch Middle Finger 3d model

Middle Finger is Back by popular demand in a Christmas Edition😅 I had many requests for this so it had to be done!

The hand is print-in-place - While printing it should be easier than the original middle finger (Which was also pretty easy) - all recommendations from the MF print are relevant here as well - Print slow, watch flows and so on...

Sleeve and Cuff are optional addition but it adds a lot to the looks :) You attach it using some glue - But don't glue the fingers from the bottom - just the sides.

Scaling: This hand has less mass than the original MF cause it's thinner and the default size is smaller, But the finger extends more. The finger this time has 2 walls so if you scale down - do not scale below 85% as finger will become a single wall. Scaling up should not be a problem.

3D PRINTING SETTINGS No supports 10% infill 2-3 walls Finger considerations:

If the finger wobbles:

  1. Use glue / make sure your adhesion is good
  2. lower speed
  3. Enable z-hop
  4. Check Z height make sure it's not to close to bed

if walls get fused:

  1. reduce flow / width of first layers
  2. make sure you don't have an elephant foot
  3. Randomize your Seam

22 Likes66 DownloadsJuly 24, 2024