Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4357672.

----

**Update 08-02-2021**: I've used the [Ender 3 Pro Roller Cover/Cable Chain Mount
](https://www.thingiverse.com/thing:4623371) by [silvr21](https://www.thingiverse.com/silvr21/) to make V3. Their Satsana remix has a very tight fit with cut-outs for the Satsana (which I use), so I've remixed their design with the original hot end connection to make an even better piece (and it really is a lot better than v1 and v2).

I've also moved the attachment a bit to the right since my cover sometimes popped off due to the chains being pushed into the side of my Ender 3 Pro.

The new files are called: 
* - _X-axis_rollers_cover_with_chain_v3.stl_
* - _X-axis_rollers_cover_with_chain_part_b_v3.stl_

The _.3mf_ file has been uploaded as well named as _x-axis_rollers_cover_with_chain_v3.3mf_.

You'll need to reprint Part B as well as I had to change it's design just a bit. It's now an even tighter fit.

---

**Update 03-10-2020**: I've used the [Ender 3 Pro X-axis Cover with Lip](https://www.thingiverse.com/thing:4578816) by [dafunda](https://www.thingiverse.com/dafunda/) to make V2. Their remix has a nice lip, so this should make the cover a lot more sturdy (see the first picture).

You'll need to reprint Part B as well as I had to shorten it a little bit since I changed the placement if the chain attachment.

The new files are named:
* - _X-Axis Cover -  Chain attachment + Lip.stl_
* - _X-Axis Cover -  Chain attachment + Lip - Part B.stl_

This time no .3mf files since the Part B one is pretty much the same but made shorter and I forgot to save the .3mf for the actual cover.

To be frank, all I did was take the .stl from dafunda and added the chain attachment from the original .3mf, tested it, tweaked it, tested it again, released it.

---

I really liked the [X-axis rollers cover](https://www.thingiverse.com/thing:4050465) by [FilBer](https://www.thingiverse.com/filber), however, I was using a remixed version of the [hot end chain connection](https://www.thingiverse.com/thing:3802593) by [Littlefiver](https://www.thingiverse.com/littlefiver) and I couldn't use both at the same time.

To resolve this issue I've remixed the reinforced hot end mount onto the x-axis roller and sliced the connection piece. Now the rollers are covered and I can still attach my chain, making it all look very sleek.

Please leave a make or a comment if you printed this yourself. Thank you!

---

**Printing**

Make sure you print both parts it as shown in the screen shots. You will need a decently calibrated machine with well defined acceleration, otherwise the fit will be quite loose.

Part B does not require supports. It's just a boring clip. ;)
 
 

**Assembly**

You'll need a single M3 bolt around 12mm. Longer is possible as you can just screw it through the entire length, but shorter will look nicer. 

After that, it's just a matter of attaching the chain to the hook. This will take some force so make sure that you don't break your chain link. The mount should be more than strong enough.

 

**How I Designed This**

Imported all the STLs into Microsoft's 3D builder, split things up and just tweak it until it looked decent and worked on my machine. 

I've included the 3MF files if someone else wants to perfect this design.

X-Axis Rollers Cover + Chain attachment + Lip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4644815.

---

Extended the BLTouch by [SitRepPope2020](https://www.thingiverse.com/thing:4389566) (original by [Leesirc](https://www.thingiverse.com/thing:4373721)) just a bit for a better fit. It's not the nicest job, but does what it should do.

**X/Y Offset**

The offset is about -50 and -14 (but please measure it for yourself). The z-offset you'll have to figure out yourself.

**Warning**

The BLTouch mount might bump into your x-axis assembly on the left. Please double check that you have proper clearance.

My X-axis switch is moved forward a bit because of  [X-Axis Stepper Damper Adapter with Filament Roller Guide](https://www.thingiverse.com/thing:3579363) by [FerretWithASpork](https://www.thingiverse.com/FerretWithASpork) and [benawhite](https://www.thingiverse.com/benawhite).

Satsana - BLTouch Mount - Extended

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4316750.

---

I wanted to have bigger screw holes and make it work on my Ender 3 Pro, so I sliced [MHDev2 upper half](https://www.thingiverse.com/thing:3951744) onto the [lower half of benawhite's Ender 3 Pro version](https://www.thingiverse.com/thing:3516416).

Z-Axis Stepper Damper Adapter - Bigger screw hole - Ender 3 Pro

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

guywithaprinter

X-Axis Rollers Cover + Chain attachment + Lip

Satsana - BLTouch Mount - Extended

Z-Axis Stepper Damper Adapter - Bigger screw hole - Ender 3 Pro