6 of my mushroom wall shelf. A great way to get hooked on them 👀 
All shelfs come in different sizes and as fridge magnet version!

**An organic shelf that “grows” from your wall.**
If you need a small shelf for anything you want to make visible every day (like your favorite Benchy or a small plant) this is the one for you. 
You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. I used 3M Tape.

Diameter of the two screw holes: 5,5mm

Size assembled: 80 mm x 115 mm x 105 mm

**Print settings**
Required build volume: 120mm x120mm x 120 mm
Material usage: 40g
Print time: 3 – 4 h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Wall shelf “Fungus”

fungus_shelf.stl

**An organic shelf that “grows” from your wall.**
If you need a small shelf for anything you want to make visible every day (like your favorite Benchys or a plant) this is the one for you. 

**Versions**
- Tinderfungus_shelf_default: The default size
- Tinderfungus_holder_default: the holder for the default size with a screw-hole diameter of 5.5mm
- Tinderfungus_shelf_small: A mini version (60% scale)
- Tinderfungus_holder_small: A holder for the mini version – simply scaling down the default version would make the holder unusable
- Tinderfungus_shelf_no_holder: The Shelf without the cut-out intended for scaling down below the mini version – must be mounted with glue or tape
- Tinderfungus_holder_for_upscaling: If you want a huge version, scale up the default shelf and use this holder – the only difference is the screw-hole size of 3mm that will be usable when scaled. 
- Tinderfungus_shelf_magnet_internal: A version for making a fridge magnet with mid-printing insertion (40% scale)
- Tinderfungus_shelf_magnet_external: A version for making a fridge magnet (40% scale)

**Instructions**
- Print the shelf and holder
- You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. I used 3M Tape. Old fashioned screws and dowels are the most reliable fixation.
- Insert the shelf by moving it horizontally onto the holder until the holder is completely inside the cutout. Then proceed to move the shelf down and the holder locks in. By lightly tapping on top of the shelf it will move down without much resistance.
- Enjoy!

**Instructions fridge magnet**
Magnet required: a 20 x 2 mm neodymium magnet

Internal magnet
- The internal magnet shelf file has a cutout inside to place a magnet during the printing process. All mushroom wall shelf designs have the cutout at the same height – so you can print all of them at the same time.
- Use a copper nozzle for printing (nonmagnetic)
- Slice the file and check the layer height of the last layer before the bridging over the hollow cutout starts. With a 0.4mm nozzle it should be at layer 15. Implement a pause after that layer with your slicer.
Start the print
- At the pause insert the magnet and continue printing. As always be careful with magnets and electronic parts!

External magnet
- Print the file
- Glue in the magnet after the printing process – the cut-out is sized to let the magnet stand out just a bit

Size default assembled ca: 210 x 120 x 65 mm

**Print settings**
Required build volume: 200 x 200 x 100 mm (for beds between 200 and 220 mm width you need to rotate it a bit to fit)
Material usage: 140g
Print time: 13h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Wall shelf “Tinder Fungus”

Tinderfungus_shelf_default.stl

**An organic shelf that “grows” from your wall.**
If you need a small shelf for anything you want to make visible every day (like your favorite Benchy or a small plant) this is the one for you. 

**Versions**
- Oysterfungus_shelf_default: The default size
- Oysterfungus _holder_default: the holder for the default size with a screw-hole diameter of 5.5mm
- Oysterfungus _shelf_small: A mini version (60% scale)
- Oysterfungus _holder_small: A holder for the mini version – simply scaling down the default version would make the holder unusable
- Oysterfungus _shelf_no_holder: The Shelf without the cut-out intended for scaling down below the mini version – must be mounted with glue or tape
- Oysterfungus _holder_for_upscaling: If you want a huge version, scale up the default shelf and use this holder – the only difference is the screw-hole size of 3mm that will be usable when scaled. 
- Oysterfungus_shelf_magnet_internal: A version for making a fridge magnet with mid-printing insertion (40% scale)
- Oysterfungus_shelf_magnet_external: A version for making a fridge magnet (40% scale)

**Instructions**
- Print the shelf and holder
- You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. I used 3M Tape. Old fashioned screws and dowels are the most reliable fixation.
- Insert the shelf by moving it horizontally onto the holder until the holder is completely inside the cutout. Then proceed to move the shelf down and the holder locks.
- Enjoy!

**Instructions fridge magnet**
Magnet required: a 20 x 2 mm neodymium magnet

Internal magnet
- The internal magnet shelf file has a cutout inside to place a magnet during the printing process. All mushroom wall shelf designs have the cutout at the same height – so you can print all of them at the same time.
- Use a copper nozzle for printing (nonmagnetic)
- Slice the file and check the layer height of the last layer before the bridging over the hollow cutout starts. With a 0.4mm nozzle it should be at layer 15. Implement a pause after that layer with your slicer.
Start the print
- At the pause insert the magnet and continue printing. As always be careful with magnets and electronic parts!

External magnet
- Print the file
- Glue in the magnet after the printing process – the cut-out is sized to let the magnet stand out just a bit

Size default assembled: 100 mm x 155 mm x 160 mm

**Print settings**
Required build volume: 160mm x160mm x 120 mm
Material usage: 130g
Print time: 11h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Wall shelf “Oyster fungus”

Oysterfungus_shelf_default.stl

**An organic shelf that “grows” from your wall.**
If you need a small shelf for anything you want to make visible every day (like your favorite Benchy or a small plant) this is the one for you. 

**Versions**
- Amanitafungus_shelf_default: The default size
- Amanitafungus _holder_default: the holder for the default size with a screw-hole diameter of 5.5mm
- Amanitafungus _shelf_small: A mini version (60% scale)
- Amanitafungus _holder_small: A holder for the mini version – simply scaling down the default version would make the holder unusable
- Amanitafungus _shelf_no_holder: The Shelf without the cut-out intended for scaling down below the mini version – must be mounted with glue or tape
- Amanitafungus _holder_for_upscaling: If you want a huge version, scale up the default shelf and use this holder – the only difference is the screw-hole size of 3mm that will be usable when scaled. 
- Amanitafungus_shelf_magnet_internal: A version for making a fridge magnet with mid-printing insertion (40% scale)
- Amanitafungus_shelf_magnet_external: A version for making a fridge magnet (40% scale)

**Instructions**
1. Print the shelf and holder
2. You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. I used 3M Tape. Old fashioned screws and dowels are the most reliable fixation.
3. Insert the shelf by moving it horizontally onto the holder until the holder is completely inside the cutout. Then proceed to move the shelf down and the holder locks.
4. Enjoy!

**Instructions fridge magnet**
Magnet required: a 20 x 2 mm neodymium magnet

Internal magnet
- The internal magnet shelf file has a cutout inside to place a magnet during the printing process. All mushroom wall shelf designs have the cutout at the same height – so you can print all of them at the same time.
- Use a copper nozzle for printing (nonmagnetic)
- Slice the file and check the layer height of the last layer before the bridging over the hollow cutout starts. With a 0.4mm nozzle it should be at layer 15. Implement a pause after that layer with your slicer.
- Start the print
- At the pause insert the magnet and continue printing. As always be careful with magnets and electronic parts!

External magnet
- Print the file
- Glue in the magnet after the printing process – the cut-out is sized to let the magnet stand out just a bit

Size default assembled ca: 100 mm x 150 mm x 150 mm

**Print settings**
Required build volume: 160mm x160mm x 120 mm
Material usage: 100g
Print time: 10h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Wall shelf “Amanita Fungus”

Amanitafungus_shelf_default.stl

**An organic shelf that “grows” from your wall.**
If you need a small shelf for anything you want to make visible every day (like your favorite Benchy or a small plant) this is the one for you. 

**Versions**
- Ostreafungus_shelf_default: The default size
- Ostreafungus _holder_default: the holder for the default size with a screw-hole diameter of 5.5mm
- Ostreafungus _shelf_small: A mini version (60% scale)
- Ostreafungus _holder_small: A holder for the mini version – simply scaling down the default version would make the holder unusable
- Ostreafungus _shelf_no_holder: The Shelf without the cut-out intended for scaling down below the mini version – must be mounted with glue or tape
- Ostreafungus _holder_for_upscaling: If you want a huge version, scale up the default shelf and use this holder – the only difference is the screw-hole size of 3mm that will be usable when scaled. 
- Ostreafungus_shelf_magnet_internal: A version for making a fridge magnet with mid-printing insertion (40% scale)
- Ostreafungus_shelf_magnet_external: A version for making a fridge magnet (40% scale)

**Instructions**
1. Print the shelf and holder
2. You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. I used 3M Tape. Old fashioned screws and dowels are the most reliable fixation.
3. Insert the shelf by moving it horizontally onto the holder until the holder is completely inside the cutout. Then proceed to move the shelf down and the holder locks.
4. Enjoy!

**Instructions fridge magnet**
Magnet required: a 20 x 2 mm neodymium magnet

Internal magnet
- The internal magnet shelf file has a cutout inside to place a magnet during the printing process. All mushroom wall shelf designs have the cutout at the same height – so you can print all of them at the same time.
- Use a copper nozzle for printing (nonmagnetic)
- Slice the file and check the layer height of the last layer before the bridging over the hollow cutout starts. With a 0.4mm nozzle it should be at layer 15. Implement a pause after that layer with your slicer.
- Start the print
- At the pause insert the magnet and continue printing. As always be careful with magnets and electronic parts!

External magnet
- Print the file
- Glue in the magnet after the printing process – the cut-out is sized to let the magnet stand out just a bit

Size default assembled: 236 mm x 120 mm x 72 mm 

**Print settings**
Required build volume: 190mm x190mm x 130 mm
Material usage: 180g
Print time: 18h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Wall shelf “Ostrea Fungus”

Ostreafungus_shelf_default.stl

**An organic shelf that “grows” from your wall.**
If you need a small shelf for anything you want to make visible every day (like your favorite Benchy or a small plant) this is the one for you. 

**Versions**
- Djamorfungus_shelf_default: The default size
- Djamorfungus _holder_default: the holder for the default size with a screw-hole diameter of 5.5mm
- Djamorfungus _shelf_small: A mini version (60% scale)
- Djamorfungus _holder_small: A holder for the mini version – simply scaling down the default version would make the holder unusable
- Djamorfungus _shelf_no_holder: The Shelf without the cut-out intended for scaling down below the mini version – must be mounted with glue or tape
- Djamorfungus _holder_for_upscaling: If you want a huge version, scale up the default shelf and use this holder – the only difference is the screw-hole size of 3mm that will be usable when scaled. 
- Djamorfungus_shelf_magnet_internal: A version for making a fridge magnet with mid-printing insertion (40% scale)
- Djamorfungus_shelf_magnet_external: A version for making a fridge magnet (40% scale)

**Instructions**
1. Print the shelf and holder
2. You can either screw or glue it onto your wall. There are various glue or tape products for wall fixation out there. I used 3M Tape. Old fashioned screws and dowels are the most reliable fixation.
3. Insert the shelf by moving it horizontally onto the holder until the holder is completely inside the cutout. Then proceed to move the shelf down and the holder locks.
4.Enjoy!

**Instructions fridge magnet**
Magnet required: a 20 x 2 mm neodymium magnet

Internal magnet
- The internal magnet shelf file has a cutout inside to place a magnet during the printing process. All mushroom wall shelf designs have the cutout at the same height – so you can print all of them at the same time.
- Use a copper nozzle for printing (nonmagnetic)
- Slice the file and check the layer height of the last layer before the bridging over the hollow cutout starts. With a 0.4mm nozzle it should be at layer 15. Implement a pause after that layer with your slicer.
- Start the print
- At the pause insert the magnet and continue printing. As always be careful with magnets and electronic parts!

External magnet
- Print the file
- Glue in the magnet after the printing process – the cut-out is sized to let the magnet stand out just a bit

Size default assembled: 176 mm x 104 mm x 141 mm

**Print settings**
Required build volume: 180mm x180mm x 110 mm
Material usage: 160g
Print time: 12h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Wall shelf starter bundle

Categories:

Tags:

Models in this collection

Wall shelf “Fungus”

Wall shelf “Tinder Fungus”

Wall shelf “Oyster fungus”

Wall shelf “Amanita Fungus”

Wall shelf “Ostrea Fungus”

Wall shelf “Djamor Fungus”