A three piece set for a clean and tidy bathroom. Inspired by all the bubbles that you get in a nice bath.

3MF Multicolor files for bambulab AMS included!
Photos by Maison Lumiere

**A beautiful soap dispenser intended for refilling.** Upcycle a dispenser of a used soap bottle to create this piece. Avoid some plastic waste and have a unique soap dispenser in your bathroom!
3MF Multicolor files for bambulab AMS included!
Fill Volume: 300ml

**Step-by-step**
- Find an empty soap dispenser bottle and unscrew the pump. Alternatively, you can buy high end looking pump, too.
- Measure the diameter of the opening of your pump where the thread sits. 

The threads of these dispensers are standardized. Most widely used are GPI/SPI Neck finishes. I included the two most common types that fit the majority of such pumps.
Soap_dispenser_A: fits 28/400 28/410 28/415 threads with a pump opening width of approximately 28 mm (1,1 inch) that fits bottle mouths of 26 - 28 mm (1.02 – 1.10 inch)
Soap_dispenser_B: fits 24/400 24/410 28/414 threads with a pump opening width of approximately 24 mm ( 0,95 inch) that fits bottle mouths of 23 - 24 mm (0.90 – 0.95 inch)

- Choose your file and print it
- Check the length of the pump tube. If the original bottle was about 250 – 400 ml it should fit. If you use a pump intended for a originally bigger bottle (f.e. 500ml) it may be a bit too long. Cut off a piece of the tube with scissors to make it fit.
- Fill the print with a liquid soap refill bag and buy those from now on
- Have fun and enjoy avoiding some plastic waste along the way!

Size of the print: 84 x 76 x 139 mm
Photos by Maison Lumiere

**Print settings**
Required build volume: 100 x 100 x 150 mm
Material usage: 80g
Print time: 6h – 7h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing: If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), increase print temperature, check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

Soap dispenser “bubbles”

Soap_dispenser_A.stl

Soap_dispenser.3mf

**An elegant soap dish with drainage in the style of my bubbles series.**
3MF Multicolor files for bambulab AMS included!

Cleaning: Empty out the drain when it is full. I advise to clean the product (as you should do with every soap dish) a few times a year. Best results are achieved with a regular old toothbrush. Scrub it for a minute or two under running warm water. 

Size assembled ca: 105 x 105 x 15 mm
Photos by Maison Lumiere

**Print settings**
Required build volume: 110 x 110 x 20 mm
Material usage: 45g in total
Print time: 4-5 h in total

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 20%
Build plate adhesion type: none

Watertight printing - If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

Soap dish “bubbles”

Top.stl

Soap_dish.3mf

**A beautiful toothbrush holder with a unscrewable bottom for easy cleaning.**
3MF Multicolor files for bambulab AMS included!

I always had trouble keeping my toothbrush holder clean. Even putting it in the dishwasher did not result in a clean, hygienic cup. That's why I designed a holder that allows you to simply unscrew the bottom and clean it more easily. This way you get a more hygienic result with less effort.

Size assembled ca: 80 x 80 x 100 mm
This is the V4
Photos by Maison Lumiere

**Print settings**
Required build volume: 100x100x100 mm
Material usage: 90g
Print time: 7h

Material: PLA
Print direction: stls are rotated correctly, check images (yes the body is printed upside down due to the threads)
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none (if you have bad bed adhesion consider using a brim for the body since it is printed upside down)

Watertight printing - If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

Bubbles bundle

Categories:

Tags:

Models in this collection

Soap dispenser “bubbles”

Soap dish “bubbles”

Toothbrush holder “bubbles”