This is a modular stand that allows you to create the perfect organizational space for your jewelry. It is also designed to be an easy and optimized print!


**Print Settings**
- Print all objects with their flat sides down, and the jewelry holders themselves upright.
  - The slicer's ‘auto orient’ feature should do this for you.
- 3 walls, 10-15% infill
- PLA is fine if using this model indoors

**Parts and Assembly**
_Please refer to the gif above to see how each part fits together_
_Parts are labeled in the "Modular Jewelry Holder v8 - Build Plate" 3mf file_

1. You need 1 of each of the following models:
- base
- stand base
- The "top" model isn't necessary but caps off the top of the organizer to provide a cleaner look

2. You need at least 1 of the following objects, but can print and stack as many as you need - this is the modular part of the stand
- extension
- Note: I've personally tested it with 3 and it is stable.

3. You need as many of the following objects as you have 3-hole slots in your final configuration
-  jewelry holder

4. Optionally, you can print the following object to hold jewelry on the side of the stand
- side jewelry holder
- Caution: They are thin and can break!


Happy printing!

Want to sell this print? Become a member today!

Modular Jewelry Stand

Modular Jewelry Holder v8.3mf

Modular Jewelry Holder v8 - Build Plate.3mf

This is a coaster that is wavy, fun, and an easy print!

**Print Settings**
- This is an easy print, most anything goes.
- To reduce visible layer lines, print in 0.2mm layer height or less!
- If you'll be using these outdoors, print in ASA or ABS

Happy printing!


Want to sell this print? Become a member today!

Wavy Drink Coaster

Joyful Coaster v1.3mf

This is our updated page holder! It is more ergonomic to use, sitting on the book at an angle your wrist and thumb more naturally rest at. The angled body also allows you to hold your book pages by the stem, from a single side, or even turn it around to get a larger surface to hold either with!

This is designed to be printed in TPU.

We've tested how this indents our pages, and 95A has worked fine for us, but if you're really concerned about page indentation, print in 85A or lower!



Happy printing!

Want to sell this model? Become a member today!

Page Holder V2

Page Holder V2.3mf

This is version 1 of our page holder design. Now free as V2 is about to be released! 

This is designed to be printed in TPU.

 We've tested how this indents our pages, and 95A has worked fine for us, but if you're really concerned about page indentation, print in 85A or lower!



Happy printing!

Want to sell this model? Become a member today!

Page Holder V1

Page Holder Final - Standard.3mf

**General**
This is a travel or home accessory allowing you to get everything from a toothpaste tube! It features a ratcheting mechanism, markers to know which way to turn, a tactile knob to twist, as well as a threaded top for a clean and secure look!

This model is an aesthetic enhancement to my standard toothpaste squeezer, and has a great tactile feel!

**Assembly**
- Follow the included pictures
- thread the center column through the bottom knob. Use a little force to get it to sit flush against the bottom knob.
- Place the ratcheting mechanism onto the the center column with the taller fins **face down**
- thread the outer tube onto the center column and make sure the teeth align with the ratcheting mechanism. This bottom knob will hang over the outer tube slightly for aesthetics
- Thread the top cap onto the thread at the top of the center column, turn until it is snug. The screw threads _should_ stop you from being able to overtighten it and introduce drag on the ratcheting mechanism, but if there is drag, unscrew the top cap slightly.

**Usage**
- Line up the center column slit with the outer tube slit
- Put the toothpaste tube through the thinner outer tube slit, and thread it through the center column slit
- Start ratcheting slowly to make sure the toothpaste tube doesn't slip out of the center column

- To release your toothpaste tube, just unscrew the top enough to disengage the ratcheting mechanism at the bottom, and unwind your tube until you can pull it out.

**Printing**
- 5-piece print, but can usually be done on 1 plate
- The 3mf included already has all parts oriented and random seems applied to parts that need it
- You need to make sure supports are enabled, there are a few parts with overhangs that were unavoidable.
- You need to make sure the threads on the center column are printed fully! A outer/inner wall of 0.4mm seems to be fine for me, but double check by checking the slicer preview page and zooming in on the center column threads.
- layer height: 0.2mm

**Feedback**
Have suggestions on ways to improve this model? Leave a comment! I'm always looking for user feedback.


Want to sell this print? Become a member today!

Toothpaste Squeezer - Seashell

Toothpaste Squeezer v6 - Sea Shell (Build Plate).3mf

**General**
This is a travel or home accessory allowing you to get everything from a toothpaste tube! It features a ratcheting mechanism, markers to know which way to turn, a tactile knob to twist, as well as a threaded top for a clean and secure look!

**Assembly**
- Follow the included pictures
- thread the center column through the bottom knob. Use a little force to get it to sit flush against the bottom knob.
- Place the ratcheting mechanism onto the the center column with the taller fins **face down**
- thread the outer tube onto the center column and make sure the teeth align with the ratcheting mechanism. This bottom knob will hang over the outer tube slightly for aesthetics
- Thread the top cap onto the thread at the top of the center column, turn until it is snug. The screw threads _should_ stop you from being able to overtighten it and introduce drag on the ratcheting mechanism, but if there is drag, unscrew the top cap slightly.

**Usage**
- Line up the center column slit with the outer tube slit
- Put the toothpaste tube through the thinner outer tube slit, and thread it through the center column slit
- Start ratcheting slowly to make sure the toothpaste tube doesn't slip out of the center column

- To release your toothpaste tube, just unscrew the top enough to disengage the ratcheting mechanism at the bottom, and unwind your tube until you can pull it out.

**Printing**
- 5-piece print, but can usually be done on 1 plate
- The 3mf included already has all parts oriented and random seems applied to parts that need it
- You need to make sure supports are enabled, there are a few parts with overhangs that were unavoidable.
- You need to make sure the threads on the center column are printed fully! A outer/inner wall of 0.4mm seems to be fine for me, but double check by checking the slicer preview page and zooming in on the center column threads.
- layer height: 0.2mm

**Feedback**
Have suggestions on ways to improve this model? Leave a comment! I'm always looking for user feedback.


Want to sell this print? Become a member today!

Home and Travel Accessories

Models in this collection

Modular Jewelry Stand

Wavy Drink Coaster

Page Holder V2

Page Holder V1

Toothpaste Squeezer - Seashell

Toothpaste Squeezer - Plain