Radios and other media players design to hold a bluetooth speaker.

Go back in time with this 1938 radio case for a bluetooth speaker. With this small, nostalgic retro version of a classic radio you can enjoy listening to old radios shows, music from then or really any era. Can also be used without the speaker for a decorative stash box to hold fun items. The knobs even twist for fidgeting fun.

This version in sized for an Altec-Lansing Mini H2O bluetooth speaker which you can get [here](https://www.amazon.com/dp/B013XJLCGU) on Amazon.

The box and lid print seperately and are both 2 color, AMS or color swapped prints (which won't exactly match the pictures, the box will have more strips). Both knobs are printed separately (no supports) and snap in place to the lid. I would recommend NOT using silk pla for the knobs as they tend to snap and break.

**Print Instructions:**
- Box prints without supports, make sure you have good plate adhesion for the corners of this box. Use the .3MF AMS file or manually color swap the stripes layers:
10.0mm-13.0mm
16.4mm-19.4mm
22.8mm-25.8mm

- Lid requires normal supports and a color swap for the speaker grill between layers 4.2mm-4.8mm. 20% Infill Recommended. ***Supports and support interface can be difficult to remove. Be gentle snipping the support interface from the grill to not damage it.*** Make sure to fully remove supports around the edge so the lid will fit on the box, it is a snug fit which will loosen up over time.

- Knob1 requires an AMS system to get the logo flush on the dial. No supports. 3 walls 30% infill.
- Knob1thick is a version to print if your filament shrinks the peg and is too loose. 3 walls 30% infill.
- Knob1swap is designed to swap colors between layers 0.6mm -1.0mm.3 walls 30% infill.
- Knob2 is one color, no supports. 3 walls 30% infill.
- Knob2thick is a version to print if your filament shrinks the peg and is too loose. 3 walls 30% infill.

Creative Commons Licenses 4.0 BY-NC-ND - Attribution, Non-Commercial, No Derivitives. A commercial license to sell these prints any many others is available by subscribing to my Thangs Commercial Partner membership plan.



1938 Radio Bluetooth Speaker Case

1938_Radio.3mf

1938_Radio.stl

The RetroMaker Radio 1957 Bluetooth Speaker holder is sized to fit an AllTec Lansing Mini H20 speaker. Dial, logo label and back plate print separately. Filaments shown - Eryone Aqua Blue Matte and CC3D Dark Blue Cyan Silk.

Radio prints best flat on it's back. Set retraction settings to low, this print has a lot of retractions around the grill mesh. Recommend printing with a brim to keep the print from warping off the plate. Minimal supports can be added for the under-mesh section but I found they were difficult to remove. Unsupported produces some stringing but it is mostly hidden when speaker and or back is added.

Back Plate with RetroMaker logo is designed to print with a filament swap. Print at .2 layer height and insert a filament change at layer 7. No Infill. No supports. Back plate without logo is one color print in place.

LogoTag is designed to print with a filament swap. Print at .2 layer height and insert a filament change at layer 6. Make sure to trim and sand edges to fit in place.

Dial and nut prints in place without supports. Nut should fit tight against the back of the radio housing. Some sanding may be required to fit nut.

Creative Commons License BY-NC-ND 4.0

Retro Radio 1957 Bluetooth Speaker Holder

retromaker_radio_1957.stl

Boombox Max Bluetooth Speaker Holder. FDM Print version. Can be printed with separate colored speaker grills or with the grill incorporated. Holds an Altec Lansing Hydro Mini Bluetooth Speaker. (could be sized up for other speaker types) #JuneTunes Rock the Bells!

Boombox_max_base_pla - Prints with no supports standing up, RetroMaker logo on the plate. Recommed 0.2mm layer height

Boombox_max_base_pla_nogrills - Prints with no supports (besides built in/removable supports) standing up, RetroMaker logo on the plate. Recommed 0.2mm layer height
Use with resin or pla separately printed grills.

Boombox_max_top_pla - Prints with supports. Iron top layer or print at 45 degree angle. Recommed 0.2mm layer height

Boombox_max_handle_pla - Print on it's side (for strength) with minimal supports for the nubs. Recommed 0.2mm layer height

Boombox_max_grill_pla2 - Print flat on plate, no supoorts. Recommed 0.2mm layer height

Resin Grills coming soon.




Creative Commons License 4.0 BY-NC-ND



Boombox Max Bluetooth Speaker Holder

boombox_max_base_pla.stl

Miniature portable record player in the mid century modern style of the 1960s. Holds a Mini H2O Altec Lansing speaker. [Amazon link to this speaker](https://a.co/d/cRBHeK0)


Top slides into a groove in the base. Slim base available here [https://than.gs/m/911495](https://than.gs/m/911495)

#FunctionalArt

**Print Instructions:**
Tonearm: Print with supports .2mm layer height
Base: Print with supports. .2mm layer height.
Top: No Supports. .2 layer height
Filament Swap
0mm main color
1.8mm Dial plane
2.4mm alternate turntable color
2.8mm Speaker Grill
5.4mm Dial Top Color

Creative Commons License 4.0 BY-NC-ND

Bluetooth Speakers

Categories:

Tags:

Models in this collection

1938 Radio Bluetooth Speaker Case

Retro Radio 1957 Bluetooth Speaker Holder

Boombox Max Bluetooth Speaker Holder

Mini 60s Record Player Bluetooth Speaker