Devin B

PLEIADES Round Waste Bin

by
Make Anything
Follow
Follow
Remix Model
Make Anything
Make Anything
|
Image 1 of 17
PLEIADES Round Waste Bin 3d model
Make Anything
Make Anything
|
Image 1 of 17
PLEIADES Round Waste Bin 3d model
2D
3D
Makes
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin - I used the 0.6mm nozzle, a 0.8mm outer all, and the other setting you said to change in Bambu Studio. Everything was scaled at 150% with the exception of the of the ring. I had to increase it's size by 1mm as the original one was too loose in the can and too tight on the lid. Now it fits just right.

The lid had some under extrusion issues but the pattern came out nice (it looks a little ****-eyed as I rotated the lid to fit on the build plate. The pattern on the bottom of the bin came out AWESOME.

The lid took some doing to pop the hinged part loose. I thought I was almost going to break but at the last second it came loose.

Thank you again for another awesome model. You are the bomb. - 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin 3d model
PLEIADES Round Waste Bin - My first print on my new bambu x1C. Very easy to print,when following the instructions. Even my wife said that she though it was Nice, the first time she said that about a print. was it because of the printer of because of the model? - 3d model
PLEIADES Round Waste Bin 3d model
This model is restricted by licensing terms. 

Keep your space clean and stylish with this round PLEIADES waste bin. This three part design utilizes a lightweight spiralized bin along with an outer rim that can hold a plastic liner, and a lid with a print in place hinge that keeps your trash out of sight, out of mind.


My PLEIADES series of prints are designed to be printed in vase/spiral mode in your slicer. I suggest printing the 'bin' part with a 0.8 mm nozzle width (even with a 0.4mm nozzle) and 3-5 bottom layers. No top layers. Make sure your slicer is not set to close small gaps. In BambuStudio/Cura I set the 'Slice gap closing radius' to 0 mm

The lid and outer rim can be printed with 3+ shells and 15-25% infill at 0.16-0.2 mm layer height. Depending on the filament and infill% you may want to increase the number of solid top layers on the lid to 6 or 7 for a smooth surface.

Use a small plastic bag for the liner. It may also be used without a liner if you only plan on using it for dry waste.

When attaching the lid to the rim, make sure to line up the connector along the inside edges, which help hold it in place. When separating the parts, it's easiest to pry up from the opposite side (closer to the hinges).


Photographed models were printed on the Bambu Lab X1-Carbon 3D Printer using Bambu Lab PETG-CF filament.* *These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!


159 Likes640 DownloadsFebruary 24, 2024


159 Likes640 DownloadsFebruary 24, 2024
This model is restricted by licensing terms.