These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

Move over boat, there is a new benchmark in town.

This robot is not only a fun print-in-place figure but it is also a very useful calibration tool.

The robot is designed with 17 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

It only uses 20g of filament and is small enough to fit on a Prusa mini or even a Voron V0.

To add to the #MakerMadness theme I have added some accessory, because what says "spring" more than a robot wearing sunglasses and holding a flower 😁.

Link to the Rock version:
https://thangs.com/mythangs/file/55887

Print Settings:

No support!
No brim!

The point of the Benchmark Bot is to find the best parameters to make it function, therefore it is difficult to recommend any settings.

That being said, I used the following parameters:
0.4mm nozzle, 0.2mm layer height, PLA, 3 walls, 4 top/bottom layers, 10% infill.

Benchmark Bot

Move over boat, there is a new benchmark in town.

This robot is not only a fun print-in-place figure but it is also a very useful calibration tool.

The robot is designed with 17 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

It only uses 20g of filament and is small enough to fit on a Prusa mini or even a Voron V0.

Benchmark Bot (Kazi Toad)

Benchmark Bot Flower

Benchmark_Bot_sunglasses_KaziToad.stl

watering can

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

This print-in-place fidget toy inspired by the Chinese Puzzle Ball is a great way to show off your multicolour or transition filament!

Models shown are printed in two varieties of Sovol PLA Silk Magic, the “Blue & Yellow & Fuchsia” and “Acid Blue & Orange.”

See here for video: https://youtu.be/OigZqhRVzOI

Select the “loose” or “tight” version depending on how tightly you want the spheres rotating within each other. 

To print, you will need to ensure that each separate sphere is properly supported. Tree supports work well, especially if you raise the object off the build plate 3mm or so. 

There is a small cylindrical plug inside the innermost ball. This is to stop the supports from generating inside the innermost ball. It can simply be removed with the supports.

See here for more Chinese Puzzle Ball designs:

Plain: https://than.gs/m/911007 
Stone: https://than.gs/m/914291 
Voronoi: https://than.gs/m/913982 

AI generated description:

"This 3D model is a highly intricate Chinese Puzzle Ball. The Chinese Puzzle Ball, also known as a mystery ball, has enjoyed a rich history in Chinese culture, often associated with conveying blessings of health, wealth, and luck. Designed in a spherical shape, this artwork is essentially a ball within multiple balls. Each layer offers a complex network of interconnecting designs and structures for an enthralling visual experience. Plain and loose styled, it displays excellent detailing, sure to add a unique charm to your 3D prints collection or project. A classic ornamental piece in 3D form, the Chinese Puzzle Ball is a creative blend of Chinese culture, mystery, complexity, and 3D printing technology."

Chinese Puzzle Ball (Plain)

Chinese Puzzle Ball Plain Loose.stl

**SKEWBITS** is an original puzzle game designed specifically for 3D printing. Fit the four unique Skewbits into various silhouettes. You may be surprised by how challenging some of the problems can be!

[Watch my video to learn more](https://youtu.be/j_jYnhOX49g)

**Basic Rules**
- Fit the 4 skewbits within each outline. You do not have to fill every space, but most solutions will.
- Only use the skewbits right side up. You may not flip the parts upside down

---

This download includes the grid and puzzle pieces. Individual problems can be downloaded below

**SKEWBITS Problems**
     • [001](https://than.gs/m/949159)
     • [002](https://than.gs/m/949162)
     • [003](https://than.gs/m/949163)
     • [004](https://than.gs/m/949165)
     • [005](https://than.gs/m/949166)
     • [006](https://than.gs/m/949167)
     • [007](https://than.gs/m/949168)
     • [008](https://than.gs/m/949169)
     • [009](https://than.gs/m/949170)
     • [010](https://than.gs/m/949171)
     • [011-015](https://than.gs/m/956501)
     • [016-020](https://than.gs/m/949178)
     • [021-025](https://than.gs/m/949179)
     • [026-030](https://than.gs/m/956502)
     • [031-035](https://than.gs/m/956562)
     • [036-040](https://than.gs/m/956564)
---

**_Printing Guidelines_**

- _Grid.stl_ : Your usual print settings should work fine. I used 15% infill, 5 top layers, 0.2mm layer height. Optionally, swap filament above 1.2mm to make the grid stand out.
- _Skewbits A-D_ : 2-3 perimeters, 0.16mm layer height. No supports. Proper extrusion is important to ensure the print-in-place hinges are sturdy without fusing together (Clearance is 0.3mm). Use the colors indicated by the filenames if you want to match the solution guide. **Prints right side up.**
- _Grid_TPUgrip.stl_ -  Optional grip for the bottom of the grid. Print solid using [Ninjaflex TPU](https://bit.ly/ninjaFLEX)(Also on [Amazon](https://amzn.to/45IhDt9)) or similar. Glue in place using [E6000 adhesive](https://amzn.to/3FrgcV9), etc.
- _Grid_LaserGrip.svg_ : Optional grip for the bottom of the grid. Designed for lasercutting. I used 3mm cork. Watch [my video](https://youtu.be/j_jYnhOX49g) for details.

---

Congratulations to Benji S. for winning the first two competitions! There is a *new competition*. The first players to send photo proof to competitions@makeanything.design after solving puzzles 026-30 and 026-40 will get $100 and $250 towards 3DJake.com 

---

Photographed models were printed using PolyTerra Matte PLA [(US Link)](https://bit.ly/polyTerra) Also on [Amazon](https://amzn.to/3PHOxFA)

SKEWBITS Puzzle Game for 3D Printing

Grid.stl

A fun little fidget toy! Try doing a filament swap halfway through the print to emphasis the positions and patterns of the pieces.

See here for video: https://youtu.be/5Jdjr91qIQI 

This is a print-in-place design. Once the print has fully cooled, release each joint with a gentle twist. Repeated twists will smooth the inner surface and allow for smoother motion.

A “round” and “octagonal” version is included. Both have the same inner mechanism, but the octagonal is easier to print because of the flat bottom surface. To print the round version, I recommend raising it of the print surface about 3mm and building tree support underneath to support the contoured bottom surface.


OctaTwist Fidget Toy

OctaTwist Octagonal.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

**Tight Tolerance Long Bony Basilisk:** 
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052


Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Tight Tolerance Short Bony Basilisk: 
https://than.gs/m/936954
Loose Tolerance Short Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

Tight Tolerance Long Bony Basilisk: 
https://than.gs/m/936921
Medium Tolerance Long Bony Basilisk: Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk: **
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk: **
https://than.gs/m/937047

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

**Tight Tolerance Long Bony Basilisk: **
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk: **
Coming Soon
**Loose Tolerance Long Bony Basilisk: **
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**[Special Thanksgiving Edition](https://than.gs/m/964381) now available for [subscribers](https://than.gs/u/803093?plans=true)!**

**[Mace Edition](https://than.gs/m/969867) now available for [subscribers](https://than.gs/u/803093?plans=true)!**

---

See it in action here: https://youtube.com/shorts/A2oVwtr6K3I

Addon for my [Christmas Chain](https://than.gs/m/963853). Fun fidget toy you can spin around your fingers making tricks and impressing your imaginary friend! Print a Christmas Chain of appropriate length (I'm using length 14, it feels nice) and attach the **Ring** and **End** to the chain. Ready to spin!

Prints nicely without supports!

---

Don't forget to check out my Instagram and YouTube channel for more interesting projects!
https://www.instagram.com/jaatinen3d
https://www.youtube.com/@Jaatinen3D

Ringchaku Spinning Fidget Toy || Christmas Chain

Christmas Chain V1.2 - Ringchaku Ring.stl

My print in place experiments culminate in this cool treasure chest that has functioning lock (and a separate key that opens it).

After printing, carefully bend the lid and loosen the hinges, breaking any possible z-seam blobs inside. Then check the bottom of the chest and the lock latch; run a fingernail or some other thin part along the latch edges and slightly push apart to loosen any fused z-seams. You can use for example a flat screwdriver and push the latch from the opposite end of the larger gap to loosen it finally. It's better to make sure the latch is free before twisting the key in the lock and possibly breaking it inside.

Print-in-Place Treasure Chest with Functional Lock

Print in Place Treasure Chest.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

Print-In-Place, No Supports, Articulating Fidget Toy

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


Tolerance:
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Medium Tolerance Long Bony Basilisk: 
Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

Other Models:
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling Short Bony Basilisk:

Tight Tolerance Short Bony Basilisk: Coming Soon
Medium Tolerance Short Bony Basilisk: Coming Soon
Loose Tolerance Short Bony Basilisk: Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

Print Settings:
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**


Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Medium Tolerance Short Bony Basilisk: 
Coming Soon
Loose Tolerance Short Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

Tight Tolerance Long Bony Basilisk: 
https://than.gs/m/936921
Medium Tolerance Long Bony Basilisk: Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

This baby basilisk just can't wait to be king of the serpents.  Until then, he's content to lounge about and strike a pose for you and your friends.  He's been eating up and growing extra long in prep for the holidays.

This flexible, articulated fidget toy incorporates the unique Mimetics 3D Snap-Flex joint, allowing each body segment to wiggle freely OR snap into a fixed position to maximize your fidget experience.

Baby Basilisk was the first in a line of Snap-Flex models by Mimetics 3D, and is available for free for a limited time.  

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for Baby Basilisk to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Baby Basilisk:**
https://than.gs/m/967529
**Medium Tolerance Extra Long Baby Basilisk:**
https://than.gs/m/967621


Please try out each to see what works best for you, and let me know which version you prefer!

Make sure to revisit frequently for more thrilling Snap-Flex models to come. I'm eager to hear your feedback and collaborate on refining this model going forward.

**Other Models:**

If you like this Baby Basilisk, be sure to check out the latest articulated model here:

**Tight Tolerance Frostbite:**
https://than.gs/m/964164
**Medium Tolerance Frostbite:**
https://than.gs/m/964165
**Loose Tolerance Frostbite:**
https://than.gs/m/964166


This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.


Baby Basilisk (Extra Long) - Articulated Snap-Flex Fidget (Loose Joints)

BabyBasilisk_V2_ExtraLong_Loose.stl

The gears and shaft rotate on this model even though it prints in place. 

Printed on the [Mulcore](https://github.com/3dprintingworld/Mulcore)
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models, consider joining my [Patreon](https://www.patreon.com/3dprintingworld)



The Impossible Gear Fidget

The gears and shaft rotate on this model even though it prints in place. 

Printed on the [Mulcore]( https://github.com/3dprintingworld/Mulcore

**Support and Licensing**
If you would like to help support more free models, or get permission to sell physical copies of my models, consider joining my [Patreon]( https://www.patreon.com/3dprintingworld)


Starter Pokemon all sleeping in a pile taking a break from the big adventure, this trio is print-in-place supportless! Who do you choose? 
[Read more here: https://inspyr3d.com/take-a-break-on-that-big-adventure/ ]([url](https://inspyr3d.com/take-a-break-on-that-big-adventure/))

This support-free, single-piece 3D model is super easy to print. 
NOW IT'S YOUR TURN!

I'm inviting you to create your own 3D models of snoozing Pokémon. It's all about collaboration and fun! To read more about this endeavor, check out the project page

Contributions:
[SparkyFace5: Sleeping Sandshrew](https://than.gs/m/913745) [https://than.gs/m/913745](https://than.gs/m/913745)

Can't wait to see your fantastic creations!
be sure to tag me so I can find them :D #imINSPYR3D

#GottaCatchEmAll
#sleepingPokemon #PokémonSeries #Collaboration #CommunityProject

Sleeping Starter Pokemon

Starter Pokemon all sleeping in a pile taking a break from the big adventure, this trio is print-in-place supportless! Who do you choose? 

**Mace Windu Collapsing Lightsaber**
_Print-in-Place Version_

This lightsaber prints complete all as one piece. 

The [Replaceable Blade](https://than.gs/m/866880) version is available to my Thangs Members.

**Printing**
Supports are not required, for best results use a .4mm nozzle. Find detailed instructions on [how to print collapsing swords](https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords) on my website. If this is your first time printing, I would suggest you try the [test print]( https://social.thangs.com/m/23601) first. 

Printed on the [Muldex](https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer 
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models, consider joining my [Patreon](https://www.patreon.com/3dprintingworld)



Mace Windu Collapsing Lightsaber

**Mace Windu Collapsing Lightsaber**
_Print-in-Place Version_

This lightsaber prints complete all as one piece. 

The Removable Blade Version is available to my [Patrons.](https://www.patreon.com/3dprintingworld)

**Printing**
Supports are not required, for best results use a .4mm nozzle. Find detailed instructions on [how to print collapsing swords](https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords) on my website. If this is your first time printing, I would suggest you try the [test print]( https://social.thangs.com/m/23601) first. 

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer 
___
**Support and Licensing**
If you would like to help support more free models, or get permission to sell physical copies of my models, consider joining my [Patreon]( https://www.patreon.com/3dprintingworld)


These print-in-place Fidget Worms are hard to put down! When you do manage to put them down, use the handy Storage Apple to help them stay warm and safe.

See here for video: https://youtu.be/siRw-CrxgEA 

See here for Storage Apple:  https://social.thangs.com/m/731839 

The worm segments are connected using an enclosed ovoid joint that creates a firmer and more controlled connection than the “linked rings” joint used in most articulated designs. Print the Worms as oriented flat on the build plate. Once finished, allow the print to cool and then give each joint a small twist to free up the movement. The joints may be stiff initially but will loosen up with a few twists and turns.

Worms are provided in 10, 15, 20 segment lengths, plus a small 3 segment “test” worm. Each length comes in “Tight” or “Loose” versions.

The “Tight” versions will give you the best Fidget Worms. Materials, printers and slicers can sometimes yield slightly different results, so try printing the “Test Tight” worm first. If that works fine, then go ahead and print whatever lengths of “tight” worms you like!

If the joints bind and cannot be loosened even with force, try printing the “loose” versions instead.


Fidget Worms

Fidget Worm 15 Segment Tight Fit.stl

Such a weird design. I have no other explanation.

This fidget femur uses a print-in-place ovoid joint to create and unique tactile movement. This joint type is stronger than the interlocking double ring joints used in many articulated designs, so this design is more suitable for use as a fidget or children’s toy.

See here for video: https://youtu.be/br1-jSqgU18

Like a “ball and socket” joint, the oval-shaped ovoid from one segment is held in place by a similarly shaped socket in the neighbouring segment. Varying the relative dimensions of the ovoid and socket allows for precise control of the movement between each segment. In this design, lateral side-to-side movement is maximized, but rotation and up/down movement is slightly restricted. 
You may get some small adhesions between segments. Simply apply a bit of force to move the joint the first time, and it will be fine after that.


Fidget Femur

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**


_The winter chill that fills the air serves well to warn all those who dare to venture out into the night that frigid winds may bring Frostbite!_

Frostbite is the ninth creation in a series of Snap-Flex models by Mimetics 3D, and is available for free for a limited time.



**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows Frostbite to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for Frostbite to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Frostbite:**
https://than.gs/m/964164
**Loose Tolerance Frostbite:**
https://than.gs/m/964166

Please try out each to see what works best for you, and let me know which version you prefer!

Make sure to revisit frequently for more thrilling Snap-Flex models to come. I'm eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)


**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested
Requires good bed adhesion

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.


Frostbite, Winter Dragon Child - Articulated Snap-Flex Fidget (Medium Tightness Joints)

FrostBite_MediumTightness.stl

Useful and easy to print box with double lids to store trinkets. Comes in two versions; split in two compartments or just one big compartment.

Check out the other sizes as well:
[50x50x20mm](https://than.gs/m/845509)
[50x50x50mm](https://than.gs/m/850657)
[100x50x30mm](https://than.gs/m/845710)

Print-in-Place Split Box 80x100x30mm

Print-in-Place Split Box 80x100x30.3mf

A Storage Apple for the Fidget Worms found here: https://social.thangs.com/m/731826 

Use glue to secure the “Stem and Leaf” into the “Lid.” 


print-in-place

Most Popular of All Time

Categories

Popular

Personalize

Trending