Budget Heat Press Insert Tool (Cheap & A bit Janky)

Heat Insert Press (Budget or Jank)V1_1.step

Articulating Arms Helping hands bracket

this is a design made to hold a small helping hands base over a workpiece with articulating arms attached to a swivel over a workbench. It is helpful when soldering on delicate equipment where the base may scratch the surface or be in the way.

Yet another flux Dispenser

Gridfinity Solder Holder station

Gridfinity Solder Holder Base

Weller ET soldering tip organizer (~5.5mm base )

# **Soldering Tip Organizer**
Inner hole diameter is 6mm, holes extend ~18mm. Will hold any tips that fit those dimensions accounting for shrinkage with your printer/filament.

**Infill is required to support internal geometry.**
7% Line infill using Cura worked well for me.

Soldering Station - Gridfinity

K2_Gridfinity_Solder_Iron-Tips-Sponge.stl

TENEX - Solid State Volumetric Display

Volumetric_Display v11.step

Gridfinity Soldersucker Holder 22mm OD.3mf

Soldersucker holder for a 22mm OD Soldersucker and a 7mm OD tip

Soldering Iron Holder

Recently purchased a soldering kit and the soldering iron came with a tiny stand that provided no stability for the iron. So I created this little stand that incorporates the metal cage and the brass clippings container that came with the iron and added in a sponge for good measure. Took about 10 hours to print, but the iron is now very stable and the cleaning materials don't move around anymore.

The stand was designed in Tinkercad. You can find it at [https://www.tinkercad.com/things/6gnUHukYyih](url)


Gridfinity SMD/Component Handy Holder

Gridfinity 2x1 SMD Handy Holder Base.stl

Stickvise part lifter

A simple copy [the Stickvise PartLift](https://www.stickvise.com/accessories/partlift). I love the Stickvise and the high temperature PTFE jaws are totally worth it as well, but I am not paying $16.50 for a pair of these little part lifters.

Part is designed parametrically in Freecad. Adjust the thickness up or down to change the stiffness, and change the width as desired for the parts you will use it with as well.

Weller WLBRK12

Battery powered soldering iron with top-cover.

Gridfinity Desoldering Needels Holder

A Gridfinity Holder for Desoldering Hollow Needles. 3x3 configuration.

Gridfinity Soldering Tools Holder

A Gridfinity Soldering Tools Holder.
A Holder for 6 tools in 2x4 configuration. The slots are 3.5mm and the space between the 2 sections is 81mm.

Solder Tip Holder Gridfinity for Weller WE1010 soldering station

1x1 Gridfinity solder tip holder for Weller WE1010 soldering station for 16 Tips

Gridfinity Helping Hands Mount

A Gridfinity mount (2x2) for soldering helping hands - https://www.amazon.com/dp/B002PIA6Z4?psc=1&ref=ppx_yo2ov_dt_b_product_details

Soldering Clamp

Base Flat.stl

Thread Insert Tool

Gridfinity Holder for a Silicone Soldering Mat

A Gridfinity holder for a curled up silicone soldering mat.

Gridfinity Hakko 599B Holder

The perfect way to stash the sturdy and inexpensive [Hakko 599B brass tip cleaner](https://amzn.to/3XTwi1Q) on your favorite Gridfinity baseplate. Combine with a soldering stand and wire dispenser for a full soldering station!

To assemble, first remove the feet from the 599B's base to expose the three holes. Insert into the recess so the pegs mate with the holes. For a permanent fit, peen the pegs over with a soldering iron or other hot thingy.

Magnets or screws are VERY STRONGLY RECOMMENDED! You don't want to spill solder dust all over your project!!

Directions:
1. Print one Main Unit and two Sili-Jar Holders from any rigid filament.
2. Take one of the silicone jars apart. Put the lid on the small dish atop the Main Unit to create a screw holder.
3. Cut an X in the bottom of the jar and mount it to a Jar Holder. It will fit snugly in the recessed rim.
4. Take another jar apart and discard the lid. 
5. Completely cut out the floor of the jar bottom and mount to the other Jar Holder.
6. Glue the Jar Holders to the Main Unit. The X goes in the high position and the other goes in the lower position. The floor of both jars face upward.
7. ADD MAGNETS OR SCREWS!!
8. Solder.

Magnets or screws are mandatory for safety. A baseplate is integrated into the stand for more surface area and to manage the center of gravity.

Gridfinity is the ultimate organizer for your whole workshop! Learn more at

Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Fusion source file: https://a360.co/3Vuk7H6

Gridfinity Tips!

All storage blocks are compatible with all baseplates!
You can add [6x2mm magnets](https://amzn.to/3UuuJV9) to the corners!
You can also use [M3 screws](https://amzn.to/3VRrS9T) to secure the corners.

Soldering

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Budget Heat Press Insert Tool (Cheap & A bit Janky)

Articulating Arms Helping hands bracket

Yet another flux Dispenser

View 12 new models

Weller ET soldering tip organizer (~5.5mm base )

View 14 new models

TENEX - Solid State Volumetric Display

Gridfinity Soldersucker Holder 22mm OD.3mf

Soldering Iron Holder

Gridfinity SMD/Component Handy Holder

Stickvise part lifter

Weller WLBRK12

Gridfinity Desoldering Needels Holder

Gridfinity Soldering Tools Holder

Solder Tip Holder Gridfinity for Weller WE1010 soldering station

Gridfinity Helping Hands Mount

View 10 new models

View 12 new models

Gridfinity Holder for a Silicone Soldering Mat

Gridfinity Hakko 599B Holder